Rosslare AY-HRMR12B User manual

AY-HR/JR/KR/LR/MR12B
Proximity Readers
Installation Manual
1
1. Introduction
The AY-xR12B Series Proximity Readers (models AY-
HR12B/JR12B/KR12B/LR12B/MR12B) are RFID proximity card readers to
be installed for use with access control systems.
Figure 1: AY-xR12B Series
H J K L M
2. Technical Specifications
2.1 Electrical Characteristics
Power Supply Type Linear type (recommended)
Operating Voltage Range 5 to 16 VDC
Maximum Input Current AY-KR12B
AY-JR12B
Standby: 35 mA
Read: 50 mA
AY-HR12B
AY-LR12B
AY-MR12B
Standby: 35 mA
Read: 100 mA
Tamper Output Open collector, active low, max sink current
16 mA
Max Cable Distance to
Controller
150 meters (500 ft.)
RF Modulation ASK
Output Format Wiegand 26-Bit
Read Range (Max)* AY-HR/LR12B 12 cm (4.7 in.)
AY-JR/MR12B 10 cm (3.9 in.)
AY-KR12B 8 cm (3.2 in.)
* Measured using a Rosslare proximity card or equivalent. Range also
depends on electrical environment and proximity to metal.
2.2 Environmental Characteristics
Operating Environment Suitable for outdoor use (IP68)
Operating Temp. Range -31°C to 63°C (-25°F to 145°F)
Operating Humidity Range 0 to 95% (non-condensing)
Regulatory Approvals USA: UL 294 and FCC Part 15B
Europe: CE Listed
2.3 Physical Characteristics
Model Dimensions
(H x W x D)
Weight
AY-HR12B 109.91 x 74.91 x 15 mm (4.3 x 3.0 x 0.6 in.) 100 g (3.5 oz)
AY-JR12B 119.95 x 41.95 x 14 mm (4.7 x 1.7 x 0.6 in.) 88.5 g (3.1 oz)
AY-KR12B 79.91 x 39.91 x 12.8 mm (3.2 x 1.6 x 0.5 in.) 70.5 g (2.5 oz)
AY-LR12B 144.91 x 42.91 x 20 mm (5.7 x 1.7 x 0.8 in.) 116 g (4.1 oz)
AY-MR12B
88.91 x 88.91 x 15 mm (3.5 x 3.5 x 0.6 in.) 109 g (3.9 oz)
3. Mounting Instructions
Mount the reader with the appropriate screws (not supplied) as
indicated on the template.
To mount the reader:
1. Remove the snap-off cover to access the screw holes.
2. Determine an appropriate mounting position for the reader.
3. Peel off the back of the self-stick mounting label template included
with the unit and place at the desired mounting position.
4. Using the template as a guide, drill two holes for mounting the
reader to the surface. The hole size is indicated on the mounting
template (Figure 2).
5. Drill a 10-mm (7/16") hole for the cable. If mounting on metal,
place a grommet or electrical tape around the edge of the hole.
6. Route the interface cable from the reader to the controller. A
linear type power supply is recommended.
The proximity reader can also be mounted using strong epoxy
glue. After application, the reader should be firmly held in
place until the glue dries.
Card readers are to be used with a listed access control unit whose power
supply is UL Listed Class 2 or equivalent.
Figure 2: Mounting Templates
H J K L M

2
4. Wiring Instructions
The proximity reader is supplied with a 45-cm (18”) pigtail, having a 6-
conductor cable.
To connect the reader to the controller:
1. Prepare the reader cable by cutting the cable jacket back 3.4 cm
(1¼”) and strip the wires 1.3 cm (½”).
2. Prepare the controller cable by cutting the cable jacket back 3.4
cm (1¼”) and strip the wires 1.3 cm (½”).
3. Splice the reader pigtail wires to the corresponding controller wires
and cover each connection (Table 1).
Table 1: Wiring
Color
Wiegand Output
Red DC + Input
Black Ground
Green Data 0
White Data 1
Brown LED Control
Purple Tamper
4. If the tamper output is being utilized, connect the purple wire to
the correct input on the controller.
5. Trim and cover all conductors that are not used.
•The individual wires coming out of the reader are color coded
according to the recommended Wiegand standard.
•When using a separate power supply for the reader, this supply
and the controller's power supply must have a common ground.
•The cable shield wire on the reader should be attached to an earth
ground (best) or signal ground connection at the panel or power
supply end of the cable. This configuration is best for shielding the
reader cable from external interference.
5. Testing
The reader should be tested after wiring it to a power supply and the
controller.
To test the reader:
1. Power up the reader.
The LED and beeper activate three times. This indicates that the
reader is working properly.
2. Present the appropriate type of proximity card to the reader.
The LED momentarily flashes green and a short beep is emitted.
This indicates that the card was read properly by the proximity
reader.
After the card data is processed by the controller, the controller can
then turn the LED green.
Refer to the controller description of the LED operation if the reader
LED is controlled by the controller.

3
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Limited Warranty
The full ROSSLARE Limited Warranty Statement is available in the Quick
Links section on the ROSSLARE website at www.rosslaresecurity.com.
Rosslare considers any use of this product as agreement to the
Warranty Terms even if you do not review them.
Contact Information
United States and Canada
Rosslare Security Products, Inc.
Southlake, TX, USA
Toll Free: [phone]
Local: [phone]
Fax: [phone]
[e-mail]
Europe
Rosslare Israel Ltd.
Rosh HaAyin, Israel
Tel: [phone]
Fax: [phone]
[e-mail]
Latin America
Rosslare Latin America
Buenos Aires, Argentina
Tel: [phone]
[e-mail]
China
Rosslare Electronics (Shenzhen) Ltd.
Shenzhen, China
Tel: [phone]
Fax: [phone]
[e-mail]
Asia Pacific, Middle East, Africa
Rosslare Enterprises Ltd.
Kowloon Bay, Hong Kong
Tel: [phone]
Fax: [phone]
[e-mail]
India
Rosslare Electronics India Pvt Ltd.
Tel/Fax: [phone]
Mobile: [phone]
[e-mail]
www.rosslaresecurity.com
0706-0960166+01