Rowlinson Large Chicken Coop User manual

No. Components Qty.
1 Front/back base frame 2
2 Side base frame (75x20x1090mm) 4
3 Plain side panel 1
4 Nest box side panel 1
5 Front apex panel (sliding door) 1
6 Front door 1
7 Back apex panel (hinged door) 1
8 Back door 1
9 Perch 1
10 Roof panel 2
11 Roof ridge 1
12 Floor 1
13 Ramp 1
14 Nest box left side panel 1
15 Nest box right side panel 1
16 Nest box back panel 1
17 Nest box top bar 1
18 Nest box floor 1
19 Nest box dividers 2
20 Nest box lid 1
21 Nest box lid weather strip 1
Large Chicken Coop English SS217E
12
3
12
6
8
Before assembly
•We recommend that time is taken to
read the instructions before starting
assembly, then follow the easy step by
step guide. The instruction sheet is only
a guide to the assembly.
Certain items may not be shown to scale.
•Check all components prior to assembly
•This product should be assembled
by no less than two people
•Drill all components where indicated
5
4
7
11
10
9
13
Recommended tools for assembly
•Cross head screw driver
•Drill
•2mm drill bit
x 2
Drill
Assembly Instructions
14
Turn buttons
7. Fitting the nest box
Slide the nest box dividers into the slots in the box. Hook the bottom of the nest box over the frame of the side panel pivot
the nest box upright and reach inside to turn the turn buttons that hold it in place. Place the nest box lid on top of the nest box.
Slot the nest box lid weather strip into the side panel on top of the lid and secure the strip to the lid using 3 x 25mm screws.
15
16
17
18 19
20 21
22
23
25 24
60mm 60mm
60mm
30mm
Important note
Ensure correct
orientation of the
turn buttons
6. Nest box
Align the back and side panels of the nest box and secure using 4 x 60mm screws. Position the top bar as shown in the di-
agram, ensure the turn buttons are facing out from the nest box. Secure the top bar using 6 x 60mm screws as shown. At-
tach the nest box floor to the bottom of the wall panels using 8 x 30mm screws.
Important information
As timber is a natural material, there are certain weather conditions that may affect the materials properties. In times of excessive dry
spells the material may lose some of its internal moisture causing a certain degree of shrinkage on a panel and in periods of excessive rain
there will be a certain amount of swelling throughout the wooden panels. This process can not be avoided. If you have problems with
certain boards shrinking in dry spells try to decrease the amount of direct sunlight on the building or the amount of air passing over the
building. During hot spells spray water directly onto the panels with the aid of a garden hose.
If in doubt of any aspect regarding the assembly, use or safety of your Chicken Coop please contact us:
Help Line: (Normal Office Hours) 01829 261 121
Email: [e-mail]
ROWLINSON GARDEN PRODUCTS LIMITED
Green Lane
Wardle Nr. Nantwich
Cheshire
CW5 6BN
www.rowgar.co.uk
No. Fixing kit Qty.
22 Hinges 2
23 Handles 3
24 Hook & eye 1
25 Turn buttons 3
27 60mm screws 10
28 50mm screws 32
29 30mm screws 8
30 25mm screws 30
31 12mm screws 8
26 80mm screws 8
Place nest box lid on
top of the nest box. En-
sure the correct orien-
tation of the roof slats
to allow water to run
off the building.
25mm
Slot the nest box weather strip
into the side panel on top of the
lid and secure the strip to the lid
using 3 x 25mm screws.
Biocidal Products Regulation EU 528/2012
Permawood ACQ1900 treated wood is a treated article that incorporates biocidal products: copper hydroxide
and Benzalkoniumchloride. They protect wood against fungal decay /rot/ and insect attack.Keep away from
food, drink and animal feeding stuffs. Avoid breathing dust when cutting treated wood.
2016 © Rowlinson Garden Products Ltd
We constantly improve the quality of our products, occasionally the
components may differ from the components shown and are only
correct at time of printing. We reserve the right to change the
specification of our products without prior notice.

3. Roof
Place a roof panel on each side of the building and secure down using 4 x 50mm screws per roof panel. With both panels
in place, position the roof ridge on top of the panels and secure down using 4 x 60mm screws.
50mm
50mm
50mm
50mm
80mm
80mm
50mm
50mm
Make sure the perch is in
place before securing the
front an back panels.
50mm
50mm
It is recommended to drill pilot
holes with a 2mm drill for each
screw in this section.
Drill
It is recommended to drill pilot holes with a 2mm
drill for each screw in this section.
Drill
4. Floor and ramp
Fix two handles to the front edge of the the floor using 4 x 25mm screws per handle. At the back of the coop, slide the
floor in the opening under the door. Position the hook on the front panel and the eye on the door, secure each part using 4
x 12mm screws, ensuring that when the two parts are screwed on, the hook is able to fit into the eye to hold the door in
the up position. Rest the ramp on the base frame.
Slot the front door
into the runners.
25mm
12mm
5. Nest box turn buttons
Fit two turn buttons to the nest box top bar. Position the turn buttons approximately 70mm from each end and flush to
the top edge. Secure each one in place using 1 x 25mm screws.
2. Wall panels
Position the back door in the opening of the back panel. Fix each hinge to the panel and door using 6 x 25mm screws
Attach the handle to the door using 4 x 25mm screws and the turn button to the panel using 1 x 25mm screw. Place the
side panels onto the base and secure down at each corner using 1 x 50mm screw. Position the front and back panels be-
tween the side panels and secure through the front and back panels with 2 x 80mm screws per corner. Slot the front door
into the runners on the front of the front panel.
1. Base
Connect the front and back base frames together using the four side frames. Secure each end of the side frames to the
legs using 2 x 50mm screws at the end of each side frame.
50mm
Important note
As you attach the front and back panels have the perch in place
resting on top of the bottom frames of the front and back pan-
els.
Also have the front door slotted into the runners before you
move onto the next section.
25mm
25mm
It is recommended to drill pilot holes with
a 2mm drill for each of the 80mm and
50mm screws in this section.
Drill
25mm
70mm
70mm
Have the turn buttons flush to
the top edge of the bar.