Rowlinson Triple Bin Store User manual

x 2
No. Components Qty.
1Base plate 6
2End panel 2
3Dividing panel 2
4Back panels 3
5Door 3
6Left lid 1
7Centre lid 1
8Right lid 1
9Lid stay 3
10 Centre front rail 1
11 left/right front rail 2
12
3
4
5
6
7
8
9
10
Triple Bin Store
Assembly Instructions
English SS317
2013 © Rowlinson Garden Products Ltd
If in doubt of any aspect regarding the assembly, use or safety of your bin store please contact us :
Help Line (Normal Office Hours) 01829 261 121
ROWLINSON GARDEN PRODUCTS LIMITED
Green Lane
Wardle Nr. Nantwich
Cheshire
CW5 6BN
We constantly improve the quality of our products, occasionally the
components may differ from the components shown and are only
correct at time of printing. We reserve the right to change the
specification of our products without prior notice.
6. Lids
Determine which lid is which as described below, Position the lids in place. Align the pre-drilled bolt holes and insert a
bolts. Using the 100mm bolts in the end panels and the 150mm bolts in the dividing panels. Secure each bolt with a
washer and a nut. Do not over tighten the nuts. Attach two chains to the inside of each lid using 1 x 12 mm screw per
chain. Position the chains so that they can be looped round the handles of the bin and hooked back on the chain. Attach
the lid stays using 1 x 40mm screws per stay as shown.
Before assembly
•We recommend that time is taken to
read the instructions before starting
assembly, then follow the easy step
by step guide.The instruction sheet
is only a guide to the assembly.
Certain items may not be shown to scale.
•Check all components prior to assembly
•This product should be assembled
by no less than two people.
•Never attempt to erect the assembly
in high winds.
Recommended tools for assembly
•Power drill/screwdriver
•Cross head screwdriver bit
12
Drill
13
11
No. Fixing kit Qty.
12 Hinges 6
13 Slide bolt 3
14 150mm bolt 2
15 100mm bolt 2
16 Nuts 4
17 Washers 4
18 Chain 6
19 60mm screws 18
20 40mm screws 23
21 30mm screws 54
22 12mm screws 6
Important Note: To determine which roof panel is which, look at the front
edge of each lid, the overhang of the cladding at each side is different.
View of the front edges of the three lids
Left Lid Centre Lid Right Lid
Small
overhang
Large
overhang
Large
overhang
Washer
Nut
100mm
40mm
12mm
150mm
Small
overhang
100mm
Nut
Washer
Using the bin store
Position the bin inside
the store, loop the
chains around the
handles of the bin and
attach the S hook to
one of the chain links.

4. Join the two assemblies continued
Attach to the bottom of the dividing panels the remaining two base plates using 2 x 60mm screws per plate. It’s
important to note that these will sit inside just inside the other base plates see diagram below. Attach the front rails as
shown using 8 x 40mm screws.
2. Base plates
Attach two base plates to each assembly using 2 x 40mm screws per plate. Attach the plates as shown in the diagram
below, ensure that the end of each plate is flush with the corners of the side panels.
3. Join the two assemblies
Join the two assemblies together using the third back panel, with the panel at the same height as the other back panels
fix in place using 6 x 60mm screws.
60mm
60mm
1. End panels, dividing panels and back panels
Attach to a back panel one end panel and one dividing panel as shown below using 6 x 60mm screws. Create a second
assembly in the same way ensuring that the end panel and the dividing panel are on the opposite sides compared to
the first assembly.
40mm
40mm
60mm
View of the bottom of the assembly:
Base plates fitted just inside the other base plates
40mm
40mm
30mm
30mm
30mm
Important Note:
when assembling the
second assembly ensure
that the end and dividing
panels are on the
opposite sides compared
to the first assembly.
60mm
40mm
Back
baseplate
5. Doors
Attach the hinges to the frames of the doors as shown below using 3x30mm screws per hinge. Position the doors
between the panels leaving a small gap between the bottom of the doors and the base plates. Secure the hinges to the
outer side panels using 3x30mm screws per hinge. For each door position the two parts of the slide bolt as shown
below and secure using 6x30mm screws for each bolt set.

4. Join the two assemblies continued
Attach to the bottom of the dividing panels the remaining two base plates using 2 x 60mm screws per plate. It’s
important to note that these will sit inside just inside the other base plates see diagram below. Attach the front rails as
shown using 8 x 40mm screws.
2. Base plates
Attach two base plates to each assembly using 2 x 40mm screws per plate. Attach the plates as shown in the diagram
below, ensure that the end of each plate is flush with the corners of the side panels.
3. Join the two assemblies
Join the two assemblies together using the third back panel, with the panel at the same height as the other back panels
fix in place using 6 x 60mm screws.
60mm
60mm
1. End panels, dividing panels and back panels
Attach to a back panel one end panel and one dividing panel as shown below using 6 x 60mm screws. Create a second
assembly in the same way ensuring that the end panel and the dividing panel are on the opposite sides compared to
the first assembly.
40mm
40mm
60mm
View of the bottom of the assembly:
Base plates fitted just inside the other base plates
40mm
40mm
30mm
30mm
30mm
Important Note:
when assembling the
second assembly ensure
that the end and dividing
panels are on the
opposite sides compared
to the first assembly.
60mm
40mm
Back
baseplate
5. Doors
Attach the hinges to the frames of the doors as shown below using 3x30mm screws per hinge. Position the doors
between the panels leaving a small gap between the bottom of the doors and the base plates. Secure the hinges to the
outer side panels using 3x30mm screws per hinge. For each door position the two parts of the slide bolt as shown
below and secure using 6x30mm screws for each bolt set.

x 2
No. Components Qty.
1Base plate 6
2End panel 2
3Dividing panel 2
4Back panels 3
5Door 3
6Left lid 1
7Centre lid 1
8Right lid 1
9Lid stay 3
10 Centre front rail 1
11 left/right front rail 2
12
3
4
5
6
7
8
9
10
Triple Bin Store
Assembly Instructions
English SS317
2013 © Rowlinson Garden Products Ltd
If in doubt of any aspect regarding the assembly, use or safety of your bin store please contact us :
Help Line (Normal Office Hours) 01829 261 121
ROWLINSON GARDEN PRODUCTS LIMITED
Green Lane
Wardle Nr. Nantwich
Cheshire
CW5 6BN
We constantly improve the quality of our products, occasionally the
components may differ from the components shown and are only
correct at time of printing. We reserve the right to change the
specification of our products without prior notice.
6. Lids
Determine which lid is which as described below, Position the lids in place. Align the pre-drilled bolt holes and insert a
bolts. Using the 100mm bolts in the end panels and the 150mm bolts in the dividing panels. Secure each bolt with a
washer and a nut. Do not over tighten the nuts. Attach two chains to the inside of each lid using 1 x 12 mm screw per
chain. Position the chains so that they can be looped round the handles of the bin and hooked back on the chain. Attach
the lid stays using 1 x 40mm screws per stay as shown.
Before assembly
•We recommend that time is taken to
read the instructions before starting
assembly, then follow the easy step
by step guide.The instruction sheet
is only a guide to the assembly.
Certain items may not be shown to scale.
•Check all components prior to assembly
•This product should be assembled
by no less than two people.
•Never attempt to erect the assembly
in high winds.
Recommended tools for assembly
•Power drill/screwdriver
•Cross head screwdriver bit
12
Drill
13
11
No. Fixing kit Qty.
12 Hinges 6
13 Slide bolt 3
14 150mm bolt 2
15 100mm bolt 2
16 Nuts 4
17 Washers 4
18 Chain 6
19 60mm screws 18
20 40mm screws 23
21 30mm screws 54
22 12mm screws 6
Important Note: To determine which roof panel is which, look at the front
edge of each lid, the overhang of the cladding at each side is different.
View of the front edges of the three lids
Left Lid Centre Lid Right Lid
Small
overhang
Large
overhang
Large
overhang
Washer
Nut
100mm
40mm
12mm
150mm
Small
overhang
100mm
Nut
Washer
Using the bin store
Position the bin inside
the store, loop the
chains around the
handles of the bin and
attach the S hook to
one of the chain links.