Roxell HaiKoo User manual

00903419 *00903419*009-2720
®
User Guide
EN ENGLISH
Original User Guide

HAIKOO IN LINE -- USER'S GUIDE - EU ROXELL - 0511
0
TABLE OF CONTENTS
GENERAL INFORMATION 1.........................................................
1. OBEY THE LEGAL REGULATIONS AND THE APPLICABLE RULES! 1..................
2. INTENDED USE 1................................................................
3. NOT-INTENDED USE 1............................................................
4. LIABILITY 1.....................................................................
5. PERSONNEL QUALIFICATIONS 1..................................................
6. INFORMATION ABOUT THE RESIDUAL RISKS -- USED SAFETY SIGNS 1...............
7. DISMANTLING, STORAGE, TRANSPORT 2..........................................
8. THE LEVEL OF NOISE EMISSION 2................................................
9. MAIN SWITCH 2.................................................................
10. PROTECTION 2.................................................................
GENERAL SAFETY RULES 3........................................................
OPERATOR’S GUIDE 4/5..............................................................
OPERATOR’S GUIDE “CAGES” 6/7.....................................................
MAINTENANCE INSTRUCTIONS 8...................................................
TROUBLE SHOOTING GUIDE 9/10......................................................
DECLARATION OF INCORPORATION OF PARTLY COMPLETED MACHINERY
EC--DECLARATION OF CONFORMITY

ROXELL - 2313
DISCLAIMER : The original, authoritative version of this manual is the Dutch version produced by
ROXELLbvba.Subsequentchangestoanymanualmadebyanythirdpartyhavenotbeenreviewednorauthenticatedby
Roxell. Such changes may include, but are not limited to, translation into languages other than Dutch, and additions to or
deletionsfromtheoriginalcontent.Roxelldisclaimsresponsibilityforanyandalldamages,injuries,warrantyclaimsand/or
any other claims associated with such changes, inasmuch as such changes result in content that is different from the
authoritative Roxell--published Dutch version of the manual. For current product installation and operation information,
please contact the customer service and/or technical service departments of Roxell. Should you observe any questionable
contentin any manual,pleasenotifyRoxell immediately inwritingto: ROXELLbvba -- Industrielaan 13,9990 Maldegem --
Belgium.

ROXELL - 2720
1
General information
IMPORTANT: These instructions must be read, understood and all points observed by
the user, the responsible and operating personnel.
Obey the legal regulations and the applicable rules
This concerns, among other things, the European regulations and directives transposed into national legislation
and/or the laws, safety and accident prevention regulations that apply in the user's country.
During assembly, operation and maintenance of the installation the legal regulations concerned and the applic
able technical rules must be obeyed.
Intended use
The installation has been designed solely for intensive livestock use and has been developed according to the
applicable rules of good workmanship. Extra loading of the product is therefore prohibited. Any other use is
considered to be improper use. The manufacturer is not responsible for damage resulting there from. The user
bears sole responsibility.
Not-intended use
All use different than described in ” Intended use” is at the responsibility of the end user.
Liability
The (Extended) Warranty will not apply if any of the following has occurred: failure to conduct incoming goods
inspection with regards to the Products, improper handling, transportation, modification or repair; accident,
abuse or improper use; improper assembly, installation, connection or maintenance (having regard to Roxell’s
most current assembly, installation, connection and maintenance manuals); force majeure; negligence, lack of
supervision or of maintenance on the part of customer; normal wear and tear; use of cleansing agents and
disinfectants that are excluded in Roxell’s most current use and maintenance manuals; use of cleansing agents
and disinfectants in violation with the instructions received from the suppliers; or use of the Products in an
ATEXsurrounding.
The (Extended) Warranty shall not apply in the event of a defect caused either by materials or accessories
supplied by or services rendered by Customer; or by an intervention by a person or entity which is not
authorised or qualified for carrying out such intervention. Furthermore, the (Extended) Warranty will only apply
if the Products are used in livestock houses and if all parts or components of the Products are supplied by
Roxell.
Roxell will not be liable for any damages caused due to improper use, assembly, installation, connection or
maintenance of the Products. In this respect, the Customer expressly acknowledges that (i) all use, assembly,
installation, connection or maintenance must be done in accordance with Roxell’s most current assembly,
installation, connection and maintenance manuals and (ii) the electrical installation on which the Products must
be connected must be done in accordance with applicable local legislation on electrical installations.
Furthermore, the Products must be tested both mechanically and electrically in accordance with state of the art
techniques and applicable local legislation.
Personnel Qualifications
User
The person who uses a function or operation of a product for their work or who works on the product. The user
must be able to read the instructions for use and fully understand them. The user has knowledge of the func
tioning and construction of the installation.
Technically trained person
An expert who can assemble and maintain the installation (mechanically/electrically), and resolve malfunc
tions. On the basis of his/her technical training and experience, he/she has sufficient knowledge to be able to
assess activities, recognise possible dangers and rectify dangerous situations.
Storage
Put all parts to be assembled in a room or at a location where the not yet assembled components are protected
against weather influences.

ROXELL - 2720
2
Transport
Depending on the size of the parts and according to local circumstances and local legislation, the parts of the
machinehavetobetransportedwithaforklift.
The forklift must be operated by a qualified person and in accordance with the rules of good workmanship.
When lifting the load, always check if the center of gravity of the load is stable.
Dismantling
Dismantle the installation and its components in accordance with the environmental legislation of the country or
the local authorities applicable at that time. All functioning products and exchange parts must be stored and
disposed of in accordance with the applicable environmental regulations.
Environmental information for customers in the European Union
The European legislation requires that equipment marked with this symbol on the product or
packaging must not be collected with unsorted household waste. This symbol indicates that the
waste electrical and electronic equipment (WEEE) cannot be disposed of in the regular household
waste. We highly recommend that you bring your product to an official collection point so that an
expert can remove the waste electrical and electronic equipment. Inform yourself of local legisla
tion on separate collection of waste electrical and electronic equipment. Respect the local regula
tions and never dispose of the product together with household waste.
Information about waste disposal - electrical/electronic material for companies
1IntheEuropeanUnion
If you have used the product for commercial purposes and you want to dispose of it, contact Roxell who will
give you information about the return of the product. It is possible that you will have to pay a disposal charge for
the return and recycling. Small products (and small quantities) can be processed by the local collection agen
cies.
2 In other countries outside the European Union
If you want to dispose of this product, contact the local authorities for information concerning the correct dispos
al procedure.
The level of noise emission
The noise level of the installation in operation does not exceed 70dB(A).
LOTOTO = Lock Out - Tag Out - Try Out
Everyone needs his own lock and tag (label), which can’t be removed by other persons. Inform all the persons
who are influenced by the procedure.
1Toblock
•Localize all sources of energy (electric, hydraulic, pneumatic).
•Switch off.
•Take the relevant installation or the process out of operation and lock it against reuse.
You can do it by placing a padlock or other blocking mechanism (Lock Out).
2Tomark
Attach a sign, label or sticker to the padlock or blocking mechanism to reveal the nature and the expected dura
tion of the work to other persons (Tag Out).
3Tocheck
•Check if the source of energy is switched off.
•Remove any remaining energy.
•Check that the installation or process is actually safe (Try Out).

ROXELL - 2720
3
Use personal protective equipment.
Ensure you wear personal protective equipment (gloves, dust masks...).
Illuminance - Sufficient lighting
•A minimum illuminance of 200 lux is necessary during usage, maintenance and installation.
•Provide at the installation (portable) emergency lighting in case of power failure.
Electrical equipment, control panels, components and drive units
•To operate control panels, there must be at least 70 cm of free space.
•Control panels must always remain closed. The key of the control panel must be in possession of an author
ized person.
•The necessary measures must be taken by the user to keep out rats, mice and other vermin from the con-
trol panels.
•If electrical equipment, control panels, components and drive units are damaged, the system must be stopped
immediately!
•Electrical equipment, control panels, components and drive units should never be sprayed with water or oth-
er liquid!
•Electrical equipment, control panels, components and drive units should never be covered with any material.
Information about the residual risks - used safety signs
There are three levels of danger, which you can recognize from the signal word
* DANGER
* WARNING
* CAUTION
The nature and source of the imminent danger and possible consequences of not obeying warnings is stated
here!
Symbol Meaning
DANGER indicates a direct imminent danger that can result in a serious or even
fatal accident if the safety measures are not respected.
WARNING indicates a possible imminent danger that can result in a serious ac
cident or damage to the product if the safety measures are not respected.
CAUTION indicates possible, dangerous situations that can result in minor phys
ical injury or material damage if the safety measures are not respected.
This symbol refers to supporting information.
Allowed
Not allowed
This symbol will be used to draw your attention to matters that are of great
importance for your safety. It means: warning - follow the safety instruc-
tions. Disconnect the current and read the safety rules.
In short: be alert. Ignoring these instructions can cause serious injur-
ies or even death.

ROXELL - 2416 HAIKOO IN LINE - -EU
3
GENERAL SAFETY RULES
Winching systeem
Liersysteem voor voer- en drinklijnen
Winching system for feed- and drink lines
Carefully read the following instructions before
USING the system
1. Before you do any repair,ormaintenance works, always disconnect the electricity sup-
ply.
2. Ensure you wear personal protection equipment (gloves, dust masks).
3. The system starts automatically.
Never use your hands at dangerous locations (feed intake boots, drive units, control units
or outlet holes in the tubes) before you have completely switched off the transport system
andmadesurethatnobody can switch it on without your knowledge.
4. Never allow unauthorized persons to enter the house in your absence.
5. Be careful when lowering or winching up the feeding lines/circuits :
-stop immediately at the slightest hitch.
-never stay underneath when lowering or winching up the lines/circuit.
6. If the auger stalls : immediately switch off the system. Carefully read the trouble shooting
guide and strictly follow instructions. Contact a technically trained person.
An auger under tension can cause very serious injuries when released.
7. Regularly check the elbow/trough and/or tube connections. Tighten if necessary.
8. Ensure that the hopper cover (grill) or cover on the 100 kg hopper closes properly.
9. Regularly check that the control unit (pan) and/or the motor handy box are properly
closed.
IMPORTANT
This SYMBOL will be used to draw your attention to matters that are
of GREAT IMPORTANCE for your SAFETY.
It means : WARNING - follow the safety instructions :
disconnect the current - re-read the safety rules.
In short : BE ALERT.IGNORING these instructions can cause SE-
RIOUS INJURIES or even DEATH.
DANGER
Minimax/HaïKoo/Comeo Nr: 002.../009.../001
Automatisch pannen voedersysteem voor vleestkuikens
Automatic pan feeding system for broilers

HAIKOO IN LINE - USER'S GUIDE - EU ROXELL - 0110
4
automatic operation
on control pan
OPERATOR’S GUIDE
For floor feeding - from day-old chicks to broilers
Weeks
0
open feed windows
12 3 45
pans full
(manual operation) closed feed windows
BROILERS
Winch up
EASY START
6
AVOID FEED WASTAGE = ADJUST FEEDER HEIGHT
Lower
Lower
- easy flowing feed : feed level ring in position 1, 2, 3 or 4
- difficult flowing feed : feed level ring in position 5, 6, 7 or 8.
Age of
birds
00900241
4114

(for partial brooding)
B
A
(FIXED INTERMEDIATE) CONTROL PAN
Take the grill in both hands at the
height of the arrows (2) and open
the grill. The pan loosens com-
pletely from the grill.
For controlled feeding : have the pans emptied once (to several times) a day.
- do not use it constantly
-useasWARNING!
AVOID DRAUGHTS
AVOID DARKNESS
FEED LEVEL RING IN POSITION 5 (MINIMUM)
* Thelastday:runthetubesemptyandletthebirdsemptythe
pans as much as possible.
* Collect the feed residues by opening all pans, and empty
them.
* Protect electrical components against water.
* Cleanthewholesystembymeansofahigh-pressureclean-
er (max. 100 Bar).
* When using aggressive detergents or disinfectants consult
your supplier.
CLEANING
2
1
Order
22
2
Now the pans can easily
be cleaned one after
another with a high
pressure cleaner (max
100Bar).
= THE MOST USED PAN
CHECK THE SUSPENSIONS OF THE 100 KG HOPPER AND THE CONTROL
UNIT AFTER HEATING UP THE BUILDING. BOTH SUSPENSIONS MUST BE
WELL STRETCHED.
OPERATOR’S GUIDE
Poultry perch system
Pull the lip to the outside
with one hand (B). Push the
pan downward with the oth-
er hand (A).
ROXELL - 0715 HAIKOO IN LINE - -EU
5
Number of birds per pan (heavy birds/light birds) (poor ventilation/good ventilation)
Broilers 50-91 (max 150kg/pan)
0715 00900241

HAIKOO IN LINE - USER'S GUIDE - EU ROXELL - 0110
6
automatic operation
on control pan
OPERATOR’S GUIDE
For cage feeding - from day-old chicks to broilers
Weeks
Age of
birds 0
open feed windows
12 3 45
pans full
(manual operation)
(manual operation)
closed feed windows
BROILERS
Winch up
EASY START
6
AVOID FEED WASTAGE = ADJUST FEEDER HEIGHT
Lower
- easy flowing feed : feed level ring in position 1, 2, 3 or 4
- difficult flowing feed : feed level ring in position 5, 6, 7 or 8.
Feed level not too high
(manual operation)
Lower
CAGES
00903930
4114

ROXELL - 0110 HAIKOO IN LINE -- USER'S GUIDE -- E U
7
Number of birds per pan (heavy birds/light birds) (poor ventilation/good ventilation)
Broilers 50--91 (max 150kg body weight/pan)
0511 00903930
Pulltheliptotheoutsidewithonehand
(B). Push the pan downward with the
other hand (A).
B
A
CONTROL PAN
Take the grill in both hands at the height of
the arrows (2) and open the grill. The pan
loosens completely from the grill.
AVOID DRAUGHTS
AVOID DARKNESS
FEED LEVEL RING IN POSITION 5 (MINIMUM)
CLEANING
2
1
Order
2
2
2
Nowthepanscaneasilybecleaned
one after another with a high
pressure cleaner.
= THE MOST USED PAN
OPERATOR’S GUIDE
* Thelastday:runthetubesemptyandletthebirdsemptythe
pans as much as possible.
* Collect the feed residues by opening all pans, and empty
them.
* Protect electrical components against water.
* Cleanthe wholesystembymeansofahigh--pressureclean-
er (max. 100 Bar).
* When using aggressive detergents or disinfectants consult
your supplier.
CAGES

HAIKOO IN LINE - USER'S GUIDE - EU ROXELL - 0715
8
MAINTENANCE INSTRUCTIONS
DANGER
Switch of
f
the main switch first.
Use personal protective equipment.
3-monthly
6-monthly
Yearly
ACTIONS IN GREY BACKGROUND MUST BE DONE BY A TECHNICALLY TRAINED PERSON.
1. Power unit
- Make fan dust-free X
- Check possible damages to electrical wiring X
2. Poultry intake boot with sensor
- Check sensor X
3. 100kg hopper (lines)
- Check level switch X
4. Suspension
- Check operation of (central) winch X
- Check operation of (central) winch. Grease after cleaning. X
- Check connection of cable X
- Check connection of pulleys X
- Check suspension of tubes and motors X
- Keep suspension cord/cable in tension X
5. Poultry perch cable above the tubes/elbows
- Check cable X
6. Pans
- Check possible damages of pans X
7. Sensors/switches
- Check operation of safety switch or sensor. X
- Check electrical wiring X
8. Control pan
- Remove the pan and clean the inside tube X
- Clean (dry) sensor head and central tube X
- Check switch of control units X
9. Lines/circuits
- Check screws and bolts in the system after the first month and after
each batch. Tighten if necessary. X
- Keep tubes level. X
- Remove all feed from the system when the system will be out of use for a
period. X

ROXELL - 0715 HAIKOO IN LINE - -EU
9
TROUBLE SHOOTING GUIDE
Switch off the main switch first.
Use personal protective equipment.
DANGER
ACTIONS IN GREY BACKGROUND MUST BE DONE BY A TECHNICALLY TRAINED PERSON.
PROBLEM CAUSE CORRECTIVE ACTION
1.None of the feeder
lines run. No current. Replace defective fuses or reset circuit breakers.
Check current supply to the house.
Defective time clock. Replace defective clock.
Time clock not properly set. Readjust tabs.
2.One/more lines do
not run.
Pans are empty
Wires from motor damaged. Measure current in motor wires. Replace wires if
defective.
Motor protection switched off. See points 3. & 4. Reset motor overload button.
Defective sensor in the control unit, or
sensor not properly adjusted. Check the good operation of the sensor.
Replace if necessary.
Control unit not functioning properly. Put the feed level ring in a higher position. Hang an
extra lamp above it. Check temperature. Control
unit must be the most attractive one, especially the
control unit of the feeder line below the Flex-Auger
control unit.
The control unit does not function
properly when the feed windows are
open
Check the motor suspension. Hang the motor hori-
zontally. Make sure that the main cable is
stretched.
Defective sensor/minimum switch
control unit or 100kg hopper. Check control unit sensor or switch. Replace if necessary.
3.Motor is often
overloaded. Oil on auger overloads the motor. Clean the auger by running repeatedly 25kgs of
feed through the line.
Not enough current supply to the
motors. Check current supply at motor location. Start the motor. Measure start current on motors. Wiring
must be thick enough to guarantee good operation
of the system.
Object blocks the auger. Motor runs,
then stalls. Feed sticks to the tubes. Check if there are no objects in the boot, the control unit and the drop holes of the feeder pans. Remove
any objects.
4.Auger stalls. Anchor bearing worn out or broken. Replace bearing. Gently slide auger back into
thetubes.Don'tletitjumpback:yourfinger or
the bearing could be damaged.
Auger not enough stretched. Shorten the auger.
Object blocks the auger. Remove the object.
5.Tubes / boot wear
rapidly,
much noise when
system runs.
Auger kinked or bent at the wear
point.
Auger end overlaps the anchor end.
Make sure not to kink the auger when using
gripping pliers. Auger must not overlap the anchor
end.
6.Not enough feed
supplied to fill up
the lines.
Flex-Auger drop holes are too small
or point upwards. Make holes wider/turn tubes with holes
downwards.
Flow regulator in boot of feed supply
system blocks passage of the feed. Adjust flow regulator to get a higher capacity.
Flex-Auger capacity is too low. Check the capacity of the Flex-Auger according the
specifications.
Check the installation of the Flex-Auger.
Notenoughtimesetonthetimeclock. Extend operation time per meal.
7.Feed drops
directly on
the adjuster ring
of the grill.
Pan not installed over the hole. Remove the top support. Install the pan ass'y over
theholeandthelips.

HAIKOO IN LINE - USER'S GUIDE - EU ROXELL - 0715
10
PROBLEM CAUSE CORRECTIVE ACTION
8.Windows are open
and feed level is
too low.
Some windows are actually closed. Adjust height of feeder line until all windows
completely open and close simultaneously.
9.Windows are
closed and feed
level is too high.
Adjuster ring set too high. Adjust height. See OPERATOR'S GUIDE.
Not all windows are closed or
completely closed. Adjust height of feeder line until all windows completely open and close simultaneously.
10.Windows are
closed and feed
level is too low.
Adjuster ring set too low. Adjust height. See OPERATOR'S GUIDE.
Feeder line not winched up high
enough. Winch up feeder line higher until all pans simultaneously are clear of the litter.
11.Hopper 1 is
empty while the
feed
level in the
second hopper
corresponds with
the position of
the level switch
Birds massively move to one side of
the house, i.e. depending upon the
position of the sun.
A. The problem occurs sporadically :
You can solve the problem by changing the
round hole in the Flex-Auger tube above
hopper 1 into a rectangular one. Install two
outlet drops above hopper 1 (see fig. 3.) if
necessary, so that more feed drops into
hopper 1. Install the level switch low in hopper
2 (see fig. 2.). Install and adjust drop tubes to
all hoppers high enough.
B. The problem occurs regularly :
Installalevelswitchhighineachhopper.
Install the level switch low in the last hopper.
Install and adjust the drop tube high, so that
the feed in tube A (over switch level) is carried
to hopper 2.
Drop tube installed and
adjusted high.
Level switch installed
low.
Hopper 1
Hopper 2
FIGURE 1. FIGURE 2.
A
Hopper 2
Case a.
Large feed reserve (A) in
case b.
Hopper 1
FIGURE 3.

Inbouwverklaring betreffende niet voltooide machines (Richtlijn 2006/42/EG, Bijlage II.1.B)
Declaration of incorporation of partly completed machinery (Directive 2006/42/EC, Annex
II.1.B)
Fabrikant/Manufacturer:
Roxell, Industrielaan 13, 9990 Maldegem
Tel: [phone]
Fax: [phone]
Verklaart geheel onder eigen verantwoordelijkheid dat het product:
Declares on its own responsibility that the product:
MiniMax/HaiKoo/CoMeo Nr: 001…/002…/009…
Automatisch pannen voedersysteem voor vleeskuikens.
Automatic pan feeding system for broilers.
Waarop deze verklaring betrekking heeft, in overeenstemming is met:
-de volgende richtlijnen: 2006/42/EG (Machinerichtlijn); 2014/30/EU (Elektromagnetische
Compatibiliteit).
-de geharmoniseerde Europese Normen: EN ISO 13857; EN 349; EN ISO 12100; EN 60204-1;
EN 61439-1; EN 61439-2
Het is verboden bovengenoemd product in gebruik te stellen voordat de machine waarin het wordt
ingebouwd in overeenstemming met de bepalingen van de Machinerichtlijn is verklaard.
Tevens verbindt de fabrikant (of zijn gemachtigde) zich om op met redenen omkleed verzoek van de
nationale autoriteiten de relevante informatie over deze niet voltooide machine door te geven. De
wijze van doorgifte is digitaal. De wijze van informatieverschaffing laat de intellectueel-
eigendomsrechten van de fabrikant van de niet voltooide machine onverlet.
(NL)
Relating to this declaration is in accordance with
-The following directives 2006/42/EC (Machinery Directive); 2014/30/EU (Electromagnetic
Compatibility).
- The harmonised European standards: EN ISO 13857; EN 349; EN ISO 12100; EN 60204-1;
EN 61439-1; EN 61439-2
This product must not be put into service until the machinery into which it is to be incorporated
has been declared in conformity with the provisions of the Machinery Directive.
The manufacturer (or its agent) also undertakes, at the duly reasoned request of the national
authorities, to provide the relevant information concerning this partly completed machinery. The
method of transmission will be digital. The manner in which the information is provided does not
prejudice the manufacturer’s intellectual property rights concerning the partly completed
machinery.
(EN)
Plaats, Datum / Place, Date: Maldegem, 01/01/2020
………………………………..
Dhr. Gino Van Landuyt
Managing Director
“This part may only be filled out if all built-in subparts are delivered by Roxell”
EG-verklaring van overeenstemming (Richtlijn 2006/42/EG, Bijlage II.1.A)
EC-declaration of conformity (Directive 2006/42/EC, Annex II.1.A)
Wij/We_________________________________________________
(naam installateur/name fitter)
_____________________________________________________________________
_____________________________________________________________________
(volledig adres en land/complete address)
Verklaren geheel onder eigen verantwoording de
Declare completely on own justification that
________________________________________________________
(naam machine/name machinery) (nummer CE-label/number CE-label)
In een installatie te hebben ingebouwd geheel volgens de Roxell-voorschriften en in
overeenstemming met de bepalingen van de Machinerichtlijn.
Has been incorporated in conformity with the provisions of the Machinery Directive and the
prescriptions of Roxell bvba.
________________________________________________________
(plaats, datum/place, date) (naam, handtekening/name, signature)
De EG-verklaring van overeenstemming / inbouwverklaring betreft uitsluitend de machine of niet
voltooide machine in de toestand waarin zij op de markt is gebracht, met uitsluiting van de later
bijvoorbeeld door de verdeler en/of installateur en/of eindgebruiker toegevoegde componenten
en/of verrichte bewerkingen.
The EC-declaration of conformity / declaration of incorporation relates exclusively to the machinery
or partly completed machine in the state in which it was placed on the market and excludes
components which are added and/or operations carried out thereafter for instance by the distributor
and/or the installer and/or the final user.
00105304
SPECIMEN

EG-verklaring van overeenstemming (Richtlijn 2006/42/EG, Bijlage II.1.A)
EC-declaration of conformity (Directive 2006/42/EC, Annex II.1.A)
Fabrikant/Manufacturer:
Roxell, Industrielaan 13, 9990 Maldegem
Tel: [phone]
Fax: [phone]
Verklaart geheel onder eigen verantwoordelijkheid dat het product:
Declares on its own responsibility that the product:
Winching system Nr: 00102368 / 00102087
Liersysteem voor voer- en drinklijnen; manueel en gemotoriseerd
Winching system for feed- and drink lines; manual and motorised
Nummer CE-label/number CE-label :______________________________________________
Waarop deze verklaring betrekking heeft, in overeenstemming is met:
-de volgende richtlijnen: 2006/42/EG (Machinerichtlijn); 2014/30/EU (Elektromagnetische
Compatibiliteit).
-de geharmoniseerde Europese Normen: EN ISO 13857; EN 349; EN ISO 12100;
gemotoriseerd: EN 60204-1; EN 61439-1; EN 61439-2
De EG-verklaring van overeenstemming / inbouwverklaring betreft uitsluitend de machine of niet voltooide
machine in de toestand waarin zij op de markt is gebracht, met uitsluiting van de later door bijvoorbeeld de
verdeler en/of installateur en/of eindgebruiker toegevoegde componenten en/of verrichte bewerkingen.
(NL)
Relating to this declaration is in accordance with
-The following directives 2006/42/EC (Machinery Directive); 2014/30/EU (Electromagnetic Compatibility).
-The harmonised European standards: EN ISO 13857; EN 349; EN ISO 12100;
motorised: EN 60204-1; EN 61439-1; EN 61439-2
The EC-declaration of conformity / declaration of incorporation relates exclusively to the machinery or partly
completed machine in the state in which it was placed on the market and excludes components which are
added and/or operations carried out thereafter for instance by the distributor and/or the installer and/or the
final user.
(EN)
Plaats, Datum / Place, Date: Maldegem, 01/01/2020
………………………………..
Dhr. Gino Van Landuyt
Managing Director
00105502
SPECIMEN


























































ROXELLbvba‐Industrielaan13,9990Maldegem(Belgium)
Tel.+3250729172‐[email protected]‐www.roxell.com

ROXELLUSAInc.‐ 720IndustrialParkRoad,AndersonMO64831(USA)
Tel.+14178456065‐[email protected]‐www.roxell.com

ROXELLMalaysia‐No.49,JalanPermata2/KS9,TamanPerindustrianAirHitam,41200Klang,Selangor(Malaysia)
Tel.+60331231767‐[e-mail]‐www.roxell.com

ROXELLРоссия‐ООО«Рокселл»ОГРН1157746055026
125167,Россия,городМосква,Ленинградскийпроспект,дом37,корпус9,помещение653
Телефон:+74959833015‐Адресэлектроннойпочты:info.russi[email protected]‐www.roxell.com