RuggedCom RuggedSwitch RS500 User manual

RuggedSwitch
RuggedSwitchRuggedSwitch
RuggedSwitch


RS500
RS500 RS500
RS500
Installation Guide
Installation GuideInstallation Guide
Installation Guide
RuggedCom Inc.
30 Whitmore Road,
Woodbridge, Ontario
Canada L4L 7Z4
Web: www.ruggedcom.com
Tel: [phone]
Fax: [phone]
Toll Free: [phone]

2
 2008 RuggedCom Inc. All rights reserved Rev101
Federal Communications Commission Radio Frequency Interference
Statement
This equipment has been tested and found to comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment This
equipment generates, uses and cad radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference on his own expense
Warning: Changes or modifications not expressly approved by RuggedCom Inc. could void the
user’s authority to operate the equipment.
Trademarks:
Ethernet is a trademark of Xerox Corporation
RuggedSwitch is a registered trademark of RuggedCom Inc
Important:
The R 500 contains no user serviceable parts. Attempted service by unauthorized personnel shall
render all warranties null and void.
The R 500 should be installed in a restricted access location where access can only be gained
by service personnel or users who have been instructed about the reasons for the restrictions
applied to the location and about any precautions that shall be taken; and access is through the
use of a tool or lock and key, or other means of security, and is controlled by the authority
responsible for the location.

3
 2008 RuggedCom Inc. All rights reserved Rev101
Table of Contents
1Product Overview.....................................................................................................................4
1.1 Functional Overview............................................................................................... 4
1.2 Feature Highlights.................................................................................................. 4
1.3 R 500 Front Panel Description ............................................................................... 5
1.4 R 500 Top and Bottom View .................................................................................. 6
2Installation ................................................................................................................................7
2.1 DIN Rail Mounting.................................................................................................. 7
2.2 Power upply Wiring and Grounding ....................................................................... 8
2.2.1 Power upply - DC Input.................................................................................... 9
2.3 HIPOT (Dielectric trength) Testing....................................................................... 10
2.4 Failsafe Output Wiring and pecifications............................................................... 11
3Technical pecifications.........................................................................................................12
3.1 Power upply pecifications ................................................................................. 12
3.2 Failsafe Relay pecifications................................................................................. 12
3.3 Networking tandards upported .......................................................................... 12
3.4 Fiber Optical pecifications................................................................................... 13
3.5 Networking Performance pecifications ................................................................. 13
3.6 Type Test pecifications....................................................................................... 14
3.7 Operating Environment......................................................................................... 15
3.8 Physical Dimensions ............................................................................................ 15
3.9 Agency Approvals ................................................................................................ 16
4Warranty.................................................................................................................................16

4
 2008 RuggedCom Inc. All rights reserved Rev101
1Product Overvie
1.1 Functional Overview
The RuggedS itch

 R 500 is a substation hardened, fiber optical Ethernet switch specifically
designed to operate in harsh environments such as those found in electric utility substations and
harsh industrial environments. The R 500 provides 4 10BaseFL fiber optical ports and one
100BaseFX port.
pecifically tested to the same standards as mission critical protective relaying equipment (i.e.
AN I/IEEE C37.90 and IEC 60255) the R 500 is ideally suited to form the Ethernet network in a
UCA2 (Utility Communications Architecture 2.0) based substation automation network. Because
the R 500 was designed to meet the demands of the substation environment it is also ideally
suited for industrial automation networks based on Industrial Ethernet. The reliability of the R 500
exceeds that of commercial Ethernet switches by having no rotating mechanical parts such as
cooling fans and by utilizing high-temperature solid-state components.
1.2 Feature Highlights
Utility Grade (i.e. substation hardened) per AN I/IEEE C37.90, IEC 60255, and the new IEC
61850-3 (2002), IEC 61000-6-5 standards
Operating temperature: -40° to 85°C (no fan)
Radiated RF Immunity: 35V/m per AN I/IEEE C37.90.2
Power supply options: 24VDC, 48VDC or 110VDC
Failsafe output relay for critical failure or error alarming
4 – 10BaseFL (10Mbps) multimode
1 – 100BaseFX fiber optical port
Full-duplex operation (no collisions)

5
 2008 RuggedCom Inc. All rights reserved Rev101
1.3 RS500 Front Panel Descri tion
Fig. 1.3.1 R 500 Front Panel Detail
ITEM Activity Comments
olid Link Established LINK LED (Yellow)
Blinking – Once per second Tx, Rx Activity
Tx LED (Red) Blinking Tx (Transmit) Activity
Rx LED (Green) Blinking Rx (Receive) Activity
POWER LED (Red) olid Power On
Safety Ground
Stud
Po er
Failsafe
Output
Relay
LED
Indicators
10BaseFL Ports
ST Connectors
Reset
Front Panel Vie
Surge Ground
DC(+)
DC(-)
Normally Open
Common
Normally Closed
LINK/Activity
Tx (Transmit)
Rx (Receive)
POWER LED
100BaseFX Port
MTRJ Connector

6
 2008 RuggedCom Inc. All rights reserved Rev101
1.4 RS500 To and Bottom View
Fig. 1.4.1 R 500 Top and Bottom View
Surge Ground
DC(+)
DC(-)
Safety Ground
Stud
Failsafe Output
Relay
Bottom Vie
Top Vie
DIN Rail Mounting
Bracket
100BaseFX Port
MTRJ Connector
10BaseFL Ports
ST Connectors
Reset
DIN Rail Mounting
Bracket

7
 2008 RuggedCom Inc. All rights reserved Rev101
2Installation
2.1 DIN Rail Mounting
Fig. 2.1.1 R 500 Rail Mounting
DIN RAIL
DIN RAIL
Mounting Latch
Scre Driver Release Action
Release Slot
Release
Direction
RS500 DIN Rail
Mounting & Release
Side Vie Front Vie
DIN RAIL

8
 2008 RuggedCom Inc. All rights reserved Rev101
2.2 Power Su ly Wiring and Grounding
Fig. 2.2.1 R 500 Power upply Inputs
The power supply input is connected as follows:
1. + = DC (+) is connected to the positive (+) terminal if the power source is DC or to the
(Hot) terminal if the power source is AC.
2. - = DC (-) is connected to the negative (-) terminal if the power source is DC or to the
(Neutral) terminal if the power source is AC.
3. Surge Ground is used as the ground conductor for all surge and transient suppression
circuitry internal to the R 500. urge Ground is connected directly to the safety ground
terminal internally.
NOTE: Since the Chassis Ground is connected to the equipment ground bus internally, HIPOT
testing cannot be performed in the field
Surge Ground
DC(+)
DC(-)
Safety Ground
Stud

9
 2008 RuggedCom Inc. All rights reserved Rev101
2.2.1 Po er Supply - DC Input
Fig. 2.2.2 Power upply – DC Input
Note: Ground bus can either be connected to the Ground Stud on the rear of the RS500 chassis,
or the Surge Ground port on the screw-in terminal block

10
 2008 RuggedCom Inc. All rights reserved Rev101
2.3 HIPOT (Dielectric Strength) Testing
HIPOT Dielectric strength testing cannot be performed in the field due to transient/surge
suppression circuitry connected to the R 500 urge/Chassis Ground. All Rugged witch products
are HIPOT tested according to IEC 60255-5 ( ection 6) during final test.

11
 2008 RuggedCom Inc. All rights reserved Rev101
2.4 Failsafe Out ut Wiring and S ecifications
The “Failsafe” output relay is provided to signal critical error conditions that may occur on the
R 500. The contacts are energized upon power up of the unit and remain energized until a critical
error occurs.
Normally Closed Common Normally Open
RS500 Failsafe Relay Outputs
*** Normal contact state prior to power being applied to unit. ***

12
 2008 RuggedCom Inc. All rights reserved Rev101
3Technical Specifications
3.1 Power Su ly S ecifications
Power Su ly Ty e Minimum
In ut
Maximum
In ut
Fuse Rating Maximum Power
Consum tion
24 VDC 18 VDC 36 VDC 5A(F)
48 VDC 36 VDC 59 VDC 3.15A(T)
HI (110 VDC) 88 VDC 150 VDC 3.15A(T)
10 W
NOTES:
1. (T) denotes time-delay fuse
2. For continued protection against risk of fire, replace only with same type and rating of fuse.
3.2 Failsafe Relay S ecifications
Parameter Value (Resistive)
Max witching Voltage 30VAC, 80VDC
Rated witching Current 0.3A @ 30VAC
1A @ 30VDC, 0.3A @ 80VDC
3.3 Networking Standards Su orted
Parameter 10Mb s Ports 100Mb s Ports Notes
IEEE 802.3  10BaseT / 10BaseFL
IEEE 802.3u  100BaseTX / 100BaseFX
IEEE 802.3x   Full Duplex Operation

13
 2008 RuggedCom Inc. All rights reserved Rev101
3.4 Fiber O tical S ecifications
Parameter Ports 1 to 4
10Mb s Ports
U link
100Mb s Port
Multi-Mode Single-Mode* Multi-Mode Single-Mode*
peed tandard 10BaseFL 100BaseFX
Connector Type T MTRJ LC
egment Length 2 km 15 km 2 km 15 km
Optical Wavelength 820nm 1310nm 1300nm 1310nm
Cable ize
Core/Cladding 62.5/125µm 9/125µm 62.5/125µm 9/125µm
Optical Tx Power
Min/Max (dBm Peak) -13.5/-7.6 -23/-15 -16/-11 -15/-8
Optical Rx ensitivity
(dBm Average) -34.4 -38 -33.5 -31
Max Optical Rx Power
(dBm Peak) -8.2 -3.0 -11 -5
Typical Optical
Power Budget (dB) 22 18 17 16.5
* Available as an option
3.5 Networking Performance S ecifications
Parameter 10Mb s Ports
(10BaseFL)
100Mb s Ports
(100BaseFX)
Notes
Latency 16us + frame time 5us + frame time
Filtering Rate 14 880 148 800 Frames/sec
MAC Address Table 8192
VLAN Address Table 4096

14
 2008 RuggedCom Inc. All rights reserved Rev101
3.6 Ty e Test S ecifications
Electrical Safety Levels Comments
Dielectric Withstand 2 kV rms for 1 minute AN I/IEEE C37.90 (1989)
IEC 60255-5 ( ection 6)
High Voltage Impulse 5 kV peak IEC 60255-5 ( ection 8)
Insulation Resistance 500 VDC for 1 minute IEC 60255-5 ( ection 6
Electrical Environment Levels Comments
High Frequency Disturbance
(Oscillatory)
2.5 kV @ 1MHz for 2s AN I/IEEE C37.90.1
IEC 60255-22-1
IEC urge 4 kV / 2 kV IEC 61000-4-5
(Level 4)
IEC Fast Transient 2 kV / 1 kV IEC 61000-4-4
(Level 4)
AN I/IEEE Fast Transient 4 kV AN I/IEEE C37.90.1
IEC Radiated RFI Immunity 10 V/m IEC 61000-4-3
AN I/IEEE Radiated RFI
Immunity
35 V/m AN I/IEEE C37.90.2
E D
(Electrostatic Discharge)
15 kV (air discharge)
8 kV (contact)
IEC 61000-4-2
(Level 4)
Atmos heric Environment Levels Comments
Temperature (Dry Cold) -40°C IEC 60068-2-1
Test Ad: 16 hrs @ -40°C
Temperature (Dry Heat) 85°C IEC 60068-2-2
Test Bd: 16 hrs @ 85°C
Humidity 95%
Non-condensing
IEC 60068-2-30
Test Db: 6 cycles, 55°C, 95%
Humidity

15
 2008 RuggedCom Inc. All rights reserved Rev101
3.7 O erating Environment
Parameter Range Comments
Ambient Operating
Temperature
-40 to 85°C Ambient Temperature as
measured from a 30cm
radius surrounding the
center of the R500
enclosure.
Ambient Relative Humidity 5% to 95% Non-condensing
Ambient torage
Temperature
-40 to 85°C
3.8 Physical Dimensions

16
 2008 RuggedCom Inc. All rights reserved Rev101
3.9 Agency A rovals
Agency Standards Comments
cC Aus, CE C A C22.2 No. 60950, UL 60950, EN 60950
EN 61000-6-2 Approved
FCC FCC Part 15, Class A Approved
4Warranty
RuggedCom warrants this product for a period of five (5) years from date of purchase. For
warranty details, visit http://www.ruggedcom.com/ or contact your customer service representative.
hould this product require warranty or service contact the factory at:
RuggedCom Inc.
30 Whitmore Road,
Woodbridge, Ontario
Canada L4L 7Z4
Phone: [phone]
Fax: [phone]
Parameter Value Comments
Dimensions 8.0 x 6.84 x 2.43 inches
(203,20) x (173,74) x (61,72) mm
(Length x Width x Height)
with mounting brackets
installed
Weight 5 lb (2.25 Kg)
Enclosure 18 gauge Galvanized teel