Rukket Sports HAACK NET PRO WITH SPIDER STEEL NETTING User manual

WHAT’S INCLUDED
QUESTIONS? GIVE US A CALL! (1-855)-478-5538
V1
Please call us if you have any questions or concerns at 1-855-4RUKKET
Please read our product safety warnings before setup
Our video instructions provide the best guidance for setting up your Haack Net Pro with Spider Steel Netting.
They can be viewed online at
HAACK NET PRO WITH SPIDER STEEL NETTING
ASSEMBLY INSTRUCTIONS
Rear Facing Net Hook (Black)
Fiberglass Rod
T-Shaped Connector
Front Facing Net Hook (Red)
Middle Base Connecting Tube
Left Base ConnectingTube
Right Base ConnectingTube
Metal Fiberglass Connector
Elastic Rope
Fiberglass Rod
Plug for Fiberglass Support Rod
Left Base Elbow
Right Base Elbow
Left Front BaseTube
Right Front BaseTube
Metal Stakes
Net
Spring Button
Target
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.
O.
P.
Q.
R.
S.

QUESTIONS? GIVE US A CALL! (1-855)-478-5538
V1
Prior to each use
- Please use adult supervision and follow the instructions when setting up and using the net.
- Regular use or abuse will eventually strain the netting and may break it, as well as extended
exposure to outdoor elements will eect the lifetime of the net.
- Do not stand behind the net.
- This net is not intended for personal protection.
- Inspect the netting and frame for damage or wear. If damage or wear is found, do not use net until new netting can
be used so the balls do not break through the net. Replacement nets can be purchased at Rukket.com
- Make sure the frame and net are assembled correctly and on a at surface, at least ten (10) feet from structures and
vehicles.
- The user should be positioned directly in front of the net(at least 10-12 feet to avoid injury of ball rebound).
- Failure to follow these precautions could result in serious injury or damage to property.
1. Assemble the base.
Note: The buttons and holes for the rear pieces are all on the top of
the pipes, while the buttons and holes for the legs are on the sides
facing inward.
2. Lay out the net so that the four sleeves are on top of the net and
the net’s black border is near the base frame. The “Rukket Sports”
and “Rukket.com”logos will be facing outward when your net is
fully assembled.
3. Assemble the berglass poles. 4. Run both berglass poles through the sleeves.
Product Safety Warning
9. Attach all 4 clips of the target to the red loops on all four corners
of the frame of the net.
HAACK NET PRO WITH SPIDER STEEL NETTING
ASSEMBLY INSTRUCTIONS

QUESTIONS? GIVE US A CALL! (1-855)-478-5538
V1
7. Hang the net by looping the top-front red loops over the red
knobs on the fronts of the side arms. Loop the front-bottom loops
over the red hooks at the ends of the frame legs.
8. Attach the two upper-rear red loops to the black knobs on the
backs of the side arms.
5. Lift one of the berglass poles upright and insert
the end closest to the base into the receiving post in
the base. Repeat on the other side.
6. Attach the upper side arms to the tops of the berglass poles
with the red knob pointing forward. You can bend the berglass
pole down to the left or right if
the top is too high to reach.
rukket
sports
9. Attach all 4 clips of the target to the red loops on all four corners
of the frame of the net. Slide buckles on target to add slack to
target. Target should not be tight.
rukket
sports
To contact us or for warranty
information, please go to:
https://rukket.com/pages/contact-us
Replacement Nets can be found
at Rukket.com
9. Attach all 4 clips of the target to the red loops on all four corners
of the frame of the net.
HAACK NET PRO WITH SPIDER STEEL NETTING
ASSEMBLY INSTRUCTIONS