RVS RVS-360-SDS User manual

360° Ultrasonic Detection Sensor System
For RVS-77555 360° HD Camera System
RVS-360-SDS
Instruction Manual
VEHICLE SAFETY -
IT'S ALL WE DO.
TM

Contents
1. Precautions................................................................................................1
2. Hints for Users...........................................................................................3
3. Specifications ............................................................................................3
4. Product Features.......................................................................................3
5. Product Installation....................................................................................4
6. Connection ................................................................................................4
7. Troubleshooting.........................................................................................6

1
1.Precautions
●Storage and Keeping
1. The storage temperature of this device is -40~+80℃, and the operating temperature is
-20~+70 ℃. The humidity is RH90%
2. Never use this device in environments with excessive moisture, dust or smoke.
3. Avoid dropping or striking this device.
4. Avoid using this device in enclosed spaces, areas with excessive vibration or subject to
severe impacts.
5. Never puncture, scratch or use abrasive cleaning materials on this device.
6. Do not place cables where they may be pinched or stepped on.
●Operating Precautions
1. The device is powered by 12 volts from panoramic equipment.
2. Make sure all cables are connected properly. Observe polarity. Improper cable connections
may damage the device.
3. Testing and inspection of the system in accordance with these instructions and a record of
the results should be listed on the daily maintenance report. The units on operating
vehicles must be tested each day prior to the vehicle's operation. Results of this test must
be recorded in the maintenance log.
4. Proper installation requires a good understanding of vehicle/machine electrical systems
and procedures, along with proficiency in the installation.
Warning!
1. Do not open the equipment’s enclosure. This can cause damage, short-circuiting or electrical
shocks that could lead to serious injury or death.
2. The equipment is not an alternative to safe driving practices.
!Special Notice
All specifications are subject to change without notice

2
●Maintenance
1. Remove all the cable connections from the device before cleaning it.
2. Clean the sensor face of any accumulation of dirt, mud, snow, ice, or debris.
3. Visually inspect the attached wiring and cable and verify that they are properly secured
and not damaged. Inspect the Radar Sensor and control box and verify that they are
securely attached to the vehicle.
Caution
Risk of electric shock
Do not open
Caution: to reduce the risk of electric shock,
Do not remove cover (or back).
No user-serviceable parts inside.
Refer servicing to qualified service personnel.
.
CAUTION
You are cautioned that any changes or modifications not expressly approved in this manual
could void your warranty and necessitate repairs.
This symbol is intended to alert the user to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may be of sufficient magnitude to
constitute risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
This symbol is intended to alert the user not to dispose of electrical and electronic
equipment

3
2.Hints for Users
1. When triggered to work, the ultrasonic obstacle detection system will start alerting after a
one-second delay.
2. If reversing at high speed, expect the ultrasonic obstacle detection system to have a
one-second delay before emitting a warning.
3. While reversing, it is indispensable to use the ultrasonic obstacle detection system. However,
the product is meant as an assisting device for safety. We declare that the safety responsibility
is borne by the driver. Make sure to keep the car at proper speed and pay attention to the
surrounding conditions while reversing.
4. There may be improper reception, deviation and error in reflected signal because of difference
in material, angle or size of obstacles.
3.Specifications
1. Number Of Sensors: 12 PCS
2. Color Of Sensors: Black (default); Optional
3. Ultrasonic Frequency: 40KHz
4. Detecting Distance: 0m---5.00m for each sensor
5. Power Supply: DC10-18V
6. Operating Temperature: -20℃~ 70℃RH90% Max.
7. Storage Temperature: -40℃~ 80℃RH90% Max.
4.Product Features
1. The ultrasonic sensor detection system consists of a master controller, extension controller, 12
ultrasonic sensors and accessories.
2. The entire system will work automatically when power is on.
3. The on-screen display will provide real-time information to the vehicle driver about the danger
zones surrounding the vehicle.

4
5. Product Installation
1st step
Install the sensors on a suitable place. The distance between sensor S6 / S7 and S1 / S12 must be
more than 1.5m, and other adjacent sensors should be installed more than 0.5m. Ideally the
sensors should be installed on the vehicle at roughly 0.6m to 0.8m above the ground.
2nd step
Make sure the sensor is installed so that it is firm and steady.
Installation of other parts
Master and extension controller should be placed in a clean and dry place.
6.Connection
1. Please pay attention to the custom wire harness for connection between the ultrasonic sensor
kit and the back-up system. Please read manual for reference and find the following drawing
for correct connection.
2. The master controller should be hooked by the custom wire harness for panoramic equipment.
The port (Data Link) on the bottom-right of the master controller is connected to the bottom-left
port (Data Link) of the extension controller via the 461-10# cable. The sensor input cables
should be plugged in sequences.
3. The controllers are powered by panoramic equipment, which are powered by vehicle power.
Installation Diagram

5
461-10# cable
Notice: *Most problems occurred in testing are usually caused by improper installation of the
sensors, they may be solved in actual application.

6
7. Troubleshooting
Symptoms
Causes
Solutions
No reaction from the system while
power is on.
No power input
Check whether the cable is
properly connected with the
panoramic equipment
No reaction on display while there
are obstacles within the detecting
area.
Improper connection of
the sensor.
Check whether the connection is
properly connected.
There is no obstacle within the
detecting area, but constant
warning prompt occurs.
There may be too much
dirt on sensors causing
some interference.
Clean the sensors.

If you have any questions
about this product, contact:
Rear View Safety, Inc.
1797 Atlantic Avenue
Brooklyn, NY 11233
800.764.1028
Vehicle Safety - It's All We Do.TM