RVS 718-7 User manual

Reverse With Condence ™ 1
OEM Frameless Rear View Replacement
Mirror Monitor with 7.3" Dual Display
Instruction Manual

Rear View Safety
2
Introduction.............................. 03
SafetyInformation.............................. 04-06
Before Beginning Installation . . . . . . . . . . . . . . . . . . . . . . 07
Installation Guide. . ........................... . 08
ViewingOptions.................................09
Wiring.................................10
TouchScreen. ..................................11
Menu . . . . . . . . . . .....................12
Grid Lines. . . . ................. . . . . . . . 13-14
Specications . . ................. . . . . . . . . 15
Warranty.......................... . . . . . 16
Disclaimer.......................... . . . . . 17
TABLE OF CONTENTS

Reverse With Condence ™ 3
NOTE! Please read all of the installation instructions
carefully before installing the product. Improper
installation will void manufacturer’s warranty.
Congratulations on purchasing a RearView Backup
Camera System!
With this manual you will be able to properly install and
operate the unit.
The Backup Camera System is intended to be installed as a
supplement aid to your standard rear view mirror that already exists
in your vehicle. The Backup Camera System should not be used as a
substitute for the standard rear view mirror or for any other mirror
that exists in your vehicle.
In some jurisdictions, it is unlawful for a person to drive a
motor vehicle equipped with aTV viewer or screen located forward of
the back of the driver’s seat or in any location that is visible, directly
or indirectly, to the driver while operating the vehicle.
INTRODUCTION

Rear View Safety
4
Please read the entire manual and follow the instructions and
warnings carefully. Failure to do so can cause serious damage and/or
injury, including loss of life. Be sure to obey all applicable local
trac and motor vehicle regulations as it pertains to this product.
Improper installation will void manufacturer’s warranty.
• The Rear View Camera System is
designed to help the driver safe-
ly detect people and/or objects
helping to avoid damage or injury.
However, you the driver, must use it
properly. Use of this system is not a
substitute for safe, proper or legal
driving.
• Never back up while looking at the
monitor alone. You should always
check behind and around the vehi-
cle when backing up, in the same
way as you would if the vehicle did
not have the RearView Camera
System.Ifyoubackupwhilelooking
only at the monitor, you may cause
damage or injury. Always back up
slowly.
•The Rear View Camera System is
not intended for use during exten-
sive back-up maneuvers or backing
into cross trac or pedestrian walk-
ways.
•Please, always remember, the area
displayed by the Rear View Camera
Systemislimited.Itdoesnotdisplay
the entire panorama that is behind
you.
USAGE:
SAFETY INFORMATION

Reverse With Condence ™ 5
•Electric shock or product
malfunction may occur if this
product is installed
incorrectly.
• Use this product within
the voltage range specied. Failure
to do so can cause
electronic shock or product
malfunction.
•Take special care when
cleaning the monitor.
•Make sure to rmly ax the prod-
uct before use.
• If smoke or a burning smell
is detected, disconnect the
system immediately.
•Where the power cable may touch
a metal case, cover the cable with
friction tape. A short circuit
or disconnected wire may cause a
re.
• While installing the Rear View
System be careful with the wire
positioning in order to avoid wire
damage.
• The Rear View System should only
be used when the vehicle is in
reverse.
• Do not watch movies or
operate the monitor while driving;
as it may cause an
accident.
• Do not install the monitor
where it may obstruct drivers
view or obstruct an air bag
device.
• Dropping the unit may cause
possible mechanical failure.
INSTALLATION:
SAFETY INFORMATION

Rear View Safety
6
SAFETY INFORMATION
If you have questions about this product, contact:
Rear View Safety
1797 Atlantic Avenue
Brooklyn, NY 11233
Tel: [phone]
IN NO EVENT SHALL SELLER OR MANUFACTURER BE
LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF
ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM
ANY DEFECTIVE PRODUCT ORTHE USE OF ANY PRODUCT.

Reverse With Condence ™ 7
Before drilling please check that no cable or wiring is on the other side
of the wall. Please clamp all wires securely to reduce the possibility
of them being damaged while vehicle is in use. Keep all cables away
from hot/moving parts and electrical noisy components.
We recommend doing a benchmark test before installation
to insure that all components are working properly.
Step 1: Choose the monitor and camera locations.
Step 2: Install all cables in vehicle, when necessary a 0.8 (20mm)
hole should be drilled for passing camera cable through vehicles
walls. Install split grommets where applicable.
Step 3: Once all cables and wiring have been properly routed, perform
a system function test by temporarily connecting the system.
BEFORE YOU BEGIN

Rear View Safety
8
INSTALLATION GUIDE
4 5
HOW TO INSTALL MIRROR MONITOR
Remove the original mirror
Car factory original mirror The plate on the windshield
CAUTION!
NOTE: Always use caution, DO NOT force the mount. We will not be responsible for broken windshields. If you
are not sure how to remove or re-install the mirror seek trained, qualied help.
Dangerous Ok
Windshield
Windshield
Dangerous Ok
1. 2.
Different cars have different brackets. It depends
on your vehicle maker and manufacturer.There are
many methods to remove the original rear view
mirror, however, please don’t force the mirror off
the bracket.
The manufacturer will not be responsible for
damage caused to your car by wrong installation of
the mirror.
Install mirror monitor on the plate
Install rear view mirror along this directionTake down your original mirror, and make
the mirror monitor ready
windshield
Please make sure to install the mirror to
the end of the bottom without any loose
Contrarotate the xed rear view mirror
Torque is about 0.8-1.3 N.m
windshield
windshield
Original Mirror Installation
4 5
HOW TO INSTALL MIRROR MONITOR
Remove the original mirror
Car factory original mirror The plate on the windshield
CAUTION!
NOTE: Always use caution, DO NOT force the mount. We will not be responsible for broken windshields. If you
are not sure how to remove or re-install the mirror seek trained, qualied help.
Dangerous Ok
Windshield
Windshield
Dangerous Ok
1. 2.
Different cars have different brackets. It depends
on your vehicle maker and manufacturer.There are
many methods to remove the original rear view
mirror, however, please don’t force the mirror off
the bracket.
The manufacturer will not be responsible for
damage caused to your car by wrong installation of
the mirror.
Install mirror monitor on the plate
Install rear view mirror along this directionTake down your original mirror, and make
the mirror monitor ready
windshield
Please make sure to install the mirror to
the end of the bottom without any loose
Contrarotate the xed rear view mirror
Torque is about 0.8-1.3 N.m
windshield
windshield
4 5
HOW TO INSTALL MIRROR MONITOR
Remove the original mirror
Car factory original mirror The plate on the windshield
CAUTION!
NOTE: Always use caution, DO NOT force the mount. We will not be responsible for broken windshields. If you
are not sure how to remove or re-install the mirror seek trained, qualied help.
Dangerous Ok
Windshield
Windshield
Dangerous Ok
1. 2.
Different cars have different brackets. It depends
on your vehicle maker and manufacturer.There are
many methods to remove the original rear view
mirror, however, please don’t force the mirror off
the bracket.
The manufacturer will not be responsible for
damage caused to your car by wrong installation of
the mirror.
Install mirror monitor on the plate
Install rear view mirror along this directionTake down your original mirror, and make
the mirror monitor ready
windshield
Please make sure to install the mirror to
the end of the bottom without any loose
Contrarotate the xed rear view mirror
Torque is about 0.8-1.3 N.m
windshield
windshield
1 2
3
Original mirror Windshield plate
1)Take down original mirror
2) Install rear view mirror
3)Tighten rear view mirror
4 5
HOW TO INSTALL MIRROR MONITOR
Remove the original mirror
Car factory original mirror The plate on the windshield
CAUTION!
NOTE: Always use caution, DO NOT force the mount. We will not be responsible for broken windshields. If you
are not sure how to remove or re-install the mirror seek trained, qualied help.
Dangerous Ok
Windshield
Windshield
Dangerous Ok
1. 2.
Different cars have different brackets. It depends
on your vehicle maker and manufacturer.There are
many methods to remove the original rear view
mirror, however, please don’t force the mirror off
the bracket.
The manufacturer will not be responsible for
damage caused to your car by wrong installation of
the mirror.
Install mirror monitor on the plate
Install rear view mirror along this directionTake down your original mirror, and make
the mirror monitor ready
windshield
Please make sure to install the mirror to
the end of the bottom without any loose
Contrarotate the xed rear view mirror
Torque is about 0.8-1.3 N.m
windshield
windshield
Caution: Do not force mount

Reverse With Condence ™ 9
VIEWING OPTIONS
Viewing Options
The view can be changed with triggers or manually with the wire
control.

Rear View Safety
10
WIRING
Wiring
Black to GND
Red to ignition +12V
5 pin female to left camera
5 pin female to right camera
5 pin female to front camera
5 pin female to backup camera
trigger line 1
trigger line 2
Green to back car singal
Wire control

Reverse With Condence ™ 11
TOUCH SCREEN
Touch Screen Operation
10 11
TOUCH BUTTONS OPERATION
full display screen: short press to enter into “menu setting” interface
split screen: unusable
reversing: long press to enter into “backup guide line” setting
left and right: unusable
Non-trigger state: channel switch
Non-trigger state:
Trigger state:
Trigger state: unusable
1
1
3
4
2
5
234 5
MENU SETTING
In “ full display screen” state, short press “ ” to enter into menu setting interface .“ ” and “ ” are to
change the gure of each setting.
About “WIRE CTR DELAY”
This function is used with wire control switch.
1. If "WIRE CTR DELAY" is setted "OFF", this function is same as the touch buton "CH" .
2.If "WIRE CTR DELAY'' is setted as other parameters, you switch one video screen to another one by wire control
switch, once the delay time is up, the screen will be automatically back to the pre-switching video screen.
“
”
BRIGHTNESS 50
{
{
{
short press to enter into “menu setting” interface
Non-trigger and reversing trigger state:Turn on/off screen
The others state: unusable In menu setting state: Parameter down
In menu setting state: Parameter up
1) Non-Trigger/Reversing trigger state: Turn on/o screen | All other
states: Not used
2) Menu State: Parameter down
3) Non-Trigger State - Full screen display: Short press to enter "Menu set-
ting" interface / Split Screen: Not used
Reversing Trigger State - Reversing: Short press to enter into "menu set-
ting" interface / Long press to enter into "Grid Line" setting
Left/RightTrigger State: Not Used
4) Menu State: Parameter Up
5) Non-Trigger State: Channel switch /Trigger state: Not used

Rear View Safety
12
MENU
Menu
10 11
TOUCH BUTTONS OPERATION
full display screen: short press to enter into “menu setting” interface
split screen: unusable
reversing: long press to enter into “backup guide line” setting
left and right: unusable
Non-trigger state: channel switch
Non-trigger state:
Trigger state:
Trigger state: unusable
1
1
3
4
2
5
234 5
MENU SETTING
In “ full display screen” state, short press “ ” to enter into menu setting interface .“ ” and “ ” are to
change the gure of each setting.
About “WIRE CTR DELAY”
This function is used with wire control switch.
1. If "WIRE CTR DELAY" is setted "OFF", this function is same as the touch buton "CH" .
2.If "WIRE CTR DELAY'' is setted as other parameters, you switch one video screen to another one by wire control
switch, once the delay time is up, the screen will be automatically back to the pre-switching video screen.
“
”
BRIGHTNESS 50
{
{
{
short press to enter into “menu setting” interface
Non-trigger and reversing trigger state:Turn on/off screen
The others state: unusable In menu setting state: Parameter down
In menu setting state: Parameter up
In full display mode, short press menu to toggle options and use the
arrow keys to change parameters.
Wire Ctr Delay
This setting controls function of the wire control switch
1) If setting is o, the wire control switch functions the same as the CH
button
2) If the setting is on the wire control switch changes the view, but the
view returns to previous state after delay time.

Reverse With Condence ™ 13
GRID LINES
Generally, to help drivers estimate the distance from obstacles, there are
three lines for reference- red, yellow, and green.Those three lines are dis-
played on the monitor when car is reversing. The green line is 9.9 feet
from the back of the car and the yellow line is 6.6 feet away. The distant
red line is 3.3 from the backside of car while the closed red line is 1.3 feet
from the car. Both reference lines on the left and right should leave 0.65
feet from the car.
Grid Lines
9.9 feet
6.6 feet
3.3 feet
9.9 feet
6.6 feet
3.3 feet
1.3 feet
The accuracy of the grid lines can vary based on how you angle your cam-
era. Therefore to compensate for inaccurancies, you can adjust the grid
lines.
Adjustment

Rear View Safety
14
GRID LINES
Grid Lines
Counterclockwise Clockwise
Short Press: Next item
Longe press: save setting and exit
Left Up Down Right
Short Press: Next item
Long Press: Save the setting and exit
ReversingState:Longpress"Menu"toenterguide
adjustment mode. We adjust left guide line rst.
Use the arrow keys to rotate the guid line coun-
terclockwise and clockwise.
Short press "Guide Line Set" to switch to next
item. Adjust line with arrow keys. Press "Guide
Line Set" to adjust right grid line.
Right position Wrong Position
Display on the monitor

Reverse With Condence ™ 15
SPECIFICATIONS
Screen Size 7.3"TFT-LCD Display
Aspect Resolution 1280 (H) X 390 (V)
Working Voltage DC10V-DC16V
Signal System PAL/AUTO/NTSC
OperatingTemperature -20°C ~ +65°C
Mirror monitor with 7.3" dual display
Ultra reective - acts as mirror as well as monitor
4 Channel - can attach up to four cameras
Adjustable distance grid lines for backing up reference
Sleek frameless design

Rear View Safety
16
WARRANTY
ONE YEAR WARRANTY
REAR VIEW SAFETY, INC. WARRANTS THIS PRODUCT AGAINST MATERIAL DEFECTS FOR A
PERIOD OF ONE YEAR FROM DATE OF PURCHASE. WE RESERVE THE RIGHT TO REPAIR OR
REPLACE ANY SUCH DEFECTIVE UNIT AT OUR SOLE DISCRETION. REAR VIEW SAFETY, INC.
IS NOT RESPONSIBLE FOR A DEFECT IN THE SYSTEM AS A RESULT OF MISUSE, IMPROPER
INSTALLATION, DAMAGE OR MISHANDLING OF THE ELECTRONIC COMPONENTS. REAR VIEW
SAFETY, INC. IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES OF ANY KIND.
THISWARRANTY ISVOID IF: DEFECTS IN MATERIALS ORWORKMANSHIP OR DAMAGES
RESULT FROM REPAIRS OR ALTERATIONS WHICH HAVE BEEN MADE OR ATTEMPTED BY
OTHERS OR THE UNAUTHORIZED USE OF NONCONFORMING PARTS; THE DAMAGE IS DUE
TO NORMAL WEAR AND TEAR, THIS DAMAGE IS DUE TO ABUSE, IMPROPER MAINTENANCE,
NEGLECT OR ACCIDENT; OR THE DAMAGE IS DUE TO USE OF THE REAR VIEW SAFETY, INC.
SYSTEM AFTER PARTIAL FAILURE OR USE WITH IMPROPER ACCESSORIES.
WARRANTY PERFORMANCE
DURINGTHE ABOVEWARRANTY PERIOD, SHOULDYOUR REAR VIEW SAFETY PRODUCT
EXHIBIT A DEFECT IN MATERIAL ORWORKMANSHIP, SUCH DEFECTWILL BE REPAIREDWHEN
THE COMPLETE REAR VIEW SAFETY, INC. PRODUCT IS RETURNED, POSTAGE PREPAID AND
INSURED,TO REAR VIEW SAFETY, INC. OTHER THAN THE POSTAGE AND INSURANCE
REQUIREMENT, NO CHARGEWILL BE MADE FOR REPAIRS COVERED BYTHIS WARRANTY.
WARRANTY DISCLAIMERS
NOWARRANTY, ORAL ORWRITTEN, EXPRESSED OR IMPLIED, OTHERTHE ABOVEWARRANTY
ISMADEWITHREGARDTOTHISREARVIEWSAFETY,INC.REARVIEWSAFETY,INC.DISCLAIMS
ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR
PURPOSE AND ALL OTHER WARRANTIES IN NO EVENT SHALL REARVIEW SAFETY. INC.
LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL, OR PUNITIVE DAMAGES OR FOR
ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGEDTO BE AS A
CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING,
BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS.

Reverse With Condence ™ 17
DISCLAIMER
DISCLAIMER
REAR VIEW SAFETY AND/OR ITS AFFILIATES DOES NOT GUARANTEE OR PROMISE THAT THE
USER OF OUR SYSTEMSWILL NOT BE IN/PART OF AN ACCIDENT OR OTHERWISE NOT COLLIDE
WITH AN OBJECT AND/OR PERSON. OUR SYSTEMS ARE NOT A SUBSTITUTE FOR CAREFUL
AND CAUTIOUS DRIVING OR FORTHE CONSISTENT ADHERENCETO ALL APPLICABLETRAFFIC
LAWS AND MOTOR VEHICLE SAFETY REGULATIONS.THE REAR VIEW SAFETY PRODUCTS ARE
NOT A SUBSTITUTE FOR REARVIEW MIRRORS OR FOR ANY OTHER MOTORVEHICLE
EQUIPMENT MANDATED BY LAW. OUR CAMERA SYSTEMS HAVE A LIMITED FIELD OF VISION
AND DO NOT PROVIDE A COMPREHENSIVEVIEW OFTHE REAR OR SIDE AREA OFTHEVEHICLE.
ALWAYS MAKE SURETO LOOK AROUNDYOURVEHICLE AND USEYOUR MIRRORSTO CONFIRM
REARWARD CLEARANCE AND THAT YOURVEHICLE CAN MANEUVER SAFELY. REARVIEW
SAFETY AND/OR ITS AFFILIATES SHALL HAVE NO RESPONSIBILITY OR LIABILITY
FOR DAMAGE AND/OR INJURY RESULTING FROM ACCIDENTS OCCURRING WITH VEHICLES
HAVING SOME OF REAR VIEW SAFETY PRODUCTS INSTALLED AND REAR VIEW SAFETY AND/
OR ITS AFFILIATES, THE MANUFACTURER, DISTRIBUTOR AND SELLER SHALL NOT BE LIABLE
FOR ANY INJURY, LOSS OR DAMAGE, INCIDENTAL OR CONSEQUENTIAL, ARISING OUT OFTHE
USE OR INTENDED USE OF THE PRODUCT. IN NO EVENT SHALL REAR VIEW SAFETY AND/OR
ITS AFFILIATES HAVE ANY LIABILITY FOR ANY LOSSES WHETHER DIRECT OR INDIRECT, IN
CONTRACT,TORT OR OTHERWISE INCURRED IN CONNECTIONWITH THE SYSTEMS,
INCLUDING BUT NOT LIMITEDTO DAMAGED PROPERTY, PERSONAL INJURY AND/OR LOSS OF
LIFE. NEITHER SHALL REAR VIEW SAFETY AND/OR ITS AFFILIATES HAVE ANY
RESPONSIBILITY FOR ANY DECISION, ACTION OR INACTIONTAKEN BY ANY PERSON IN
RELIANCE ON REAR VIEW SAFETY SYSTEMS, OR FOR ANY DELAYS, INACCURACIES AND/OR
ERRORS IN CONNECTIONWITH OUR SYSTEMS FUNCTIONS.

Rear View Safety
18
If you have any questions
about this product, contact:
Rear View Safety, Inc.
1797 Atlantic Avenue
Brooklyn, NY 11233
800.764.1028
Vehicle Safety - It's All We Do.TM