RXTEC RX-PSE808G User manual

8-Port Ethernet Gigabit PoE Switch Rev 1.0 12/01/2013 Page 1 / 7
IMPORTANT
This users guide contains information on the limitations regarding product use and function and
information on the limitations as to liability of the manufacturer. Read the entire guide carefully
•Introduction …………………………………………………..
•Power Over Ethernet (PoE) & Features ……..…………..
•Unpacking and Installation ……… .………………………..
•System Requirement……. .………………………………..
•Front Panel /LED….………………………………………….
•Hardware Installation… …………. …………….……….…..
•Technical Specification……………………………………....
•Troubleshooting ………...……………..……..……………...
Page 2
•FCC Warning:
This device has been tested and found to comply with the regulations for Class B digital equipment. Pursuant to Part
15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with users guide, may cause harmful interference to
radio communications. Operation of this devices in a residential area is likely to cause harmful interference, in which
case the user will be required to correct the interference at his/her own expense.
•CE Mark Warning:
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user
may be required to take adequate measures.
•UL Warning:
1> Elevated Operating Ambient Temperature-If installed in a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater then room ambient. Therefore, Consideration should be given to
installing the equipment in an environment compatible with manufacturer’s maximum rated ambient temperature
2> Reduced Air flow-installation of equipment in a rack should be such that the amount of air flow required for safe
operation of the equipment is not compromised.
3> Mechanical Loading-mounting of the equipment in the rack should be such as that a hazardous
Conditions is not achieved due to uneven mechanical loading.
Page 2
Page 3
Page 3
Page 4
Page 6
Page 7
Page 5
Table of Contents
Quick Installation Guide
8-Ports Gigabit 10/100/1000M PoE Switch (af Version 15.4W)

1. Introduction
The 8-Port Gigabit PoE switch is a Power Source Equipment (PSE) and fully compatible with Powered Devices (PD)
that comply with the IEEE 802.3af PoE standard. The 8 -Port Gigabit PoE Switch enables users to attach
IEEE802.3af compliant devices such as wireless Access Points (APS), VOIP phone, IP camera, printer and
Network Attached Storage (NAS) directly to the 8 -port 10/100/1000M Ethernet PoE Switch without requiring additional
power on the network. The unit is designed with home and small business users in mind and is ideal for installations
where AC power is not available or no cost-effective.
No configuration is required and installation is quick and easy. Support for Auto –MDI / MDI-X on all of the ports
eliminates the need for crossover connection to another switch or HUB. Auto -Negotiation on each port senses the
link speed of a network device ( either10/100/1000) and intelligently adjusts for compatibility and optimal performance.
* 1-Year Limited Warranty for switch and 1-Year Limited Warranty for the power adaptor are available
* This device is designed for indoor use. Do not use outdoors.
•Power Over Ethernet (PoE):
Power over Ethernet (PoE) integrates 48V power and data onto one single cable, eliminating the need to have
AC power available at all equipment locations. Power and Data are integrated onto the same cable, supporting
category 5/5e/6 up to 100 Meters. PoE provides power to PoE compatible devices, such as VOIP telephones,
wireless LAN access points, and IP security cameras.
PoE devices are readily in the market, saving up to 50% of overall installation cost by eliminating the need to install
separate electrical wiring and power outlets.
•Features:
8 x 10/100/1000Mbps Auto-negotiation Fast Ethernet RJ-45 ports with 8 ports PoE function ( port 1 ~ port 8)
Compliant with IEEE 802.3af.
Supports PoE power up to 107.8Wfor all PoE ports.
Supports PoE IEEE802.3af compliant Powered Device (PD)
Each port supports auto MDI/MDIX, so there is no need to use cross-over cables.
Full/half duplex transfer mode for each port.
Wire speed reception and transmission.
Up to 2K unicast address entities per device. Self-learning, and table aging.
9216-byte jumbo packet length.
2. Power over Ethernet (PoE) & Features
The 8-Port Gigabit PoE switch is an unmanaged 10/100/1000Mbps Gigabit Ethernet PoE switch designed to enhance
workgroup performance while providing a high level of flexibility. It provides 8 10/100/1000Mbps ports and 8
IEEE802.3af Power over Ethernet (PoE) ports for workstation, It is an ideal solution for small office and home
users to utilize a combination of Gigabit PoE and non-PoE devices.The switch automatically detects
IEEE 802.3afcompliant devices and provides power and data over a single cable.
8-Port Ethernet Gigabit PoE Switch Rev 1.0 12/01/2013 Page 2 / 7

3. Unpacking and Installation
Open the shipping carton of the 8-Port Gigabit PoE switch and carefully unpack its
contents. The carton should Included following items:
One 8-Port Gigabit 10/100/1000M Ethernet PoE Switch .
OneAC to DC PowerAdaptor
Quick Installation Guide.
If any item is found missing or damaged, Please contact your local reseller for replacement.
•Installation:
The installation of the 8-port 10/100/1000M Ethernet PoE Switch requires the following steps:
A computer with a 10/100/1000MBase-T network adapter installed
The surface must support at least 3.0Kg (6.6 lbs) for the switch.
The power adapter should be within 1.5 meters (5 feet) of the switch.
Visually inspect the DC power cord and make sure that is fully secured to the power outlet.
Make sure that there is proper heat dissipation from and adequate ventilation around the
switch. Do not place heavy objects on the switch.
4. System Requirements
8-Port Ethernet Gigabit PoE Switch Rev 1.0 12/01/2013 Page 3 / 7

Front Panel
5. Front Panel/LED/PoE Network
●: Light ☼: Blinking Slowly O: Inactive ＊: Blinking Fast
Power LED LED on: Power ON / LED off: Power off.
Speed (1-8) ●: 100Mbps, ☼: Link for 10Mbps. ＊: 1000Mbps
LINK/ACT (1-8 ) ●: Link in full duplex mode and no activity ＊: Activity ongoing
☼: Link in half duplex mode and no activity O : Link down
PoE (1 to 8) LED on: The PoE power device (PD) is connected and the port is supplying power successfully
LED off: no PoE power device (PD) connected
LED Display
Interface Port
Port 1 –8 PoE 10/100/1000Mbps Ethernet PoE Port 1 –Port 8. 8P8C RJ-45.
Rear Panel
1DC Power Input jack: DC Input 48VDC 2.5A 5.5mm/2.5mm
2Power ON / OFF switch.
8-Port Ethernet Gigabit PoE Switch Rev 1.0 12/01/2013 Page 4 / 7

6. Hardware Installation
A: Power: Connect theAC Power Cord to the 8-Port Gigabit PoE switch and then to a
power outlet.
DC Power Cord
DC power
Supply
B: Up-Link Connect a CAT-5, 5e 6 RJ-45 network cable or 50/62.5um Fiber cable from
the Computer or Router to port 1 –8.
Setup your Networking
8-Port Ethernet Gigabit PoE Switch Rev 1.0 12/01/2013 Page 5 / 7

7. Technical Specifications
Standard IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3x Full Duplex Flow Control
IEEE 802.3ab 1000Base-T Gigabit Ethernet (twisted-pair copper)
IEEE 802.3af Power over Ethernet
Protocol CSMA/CD
Data Transfer Rate Ethernet: 10Mbps (half-duplex), 20Mbps (full-duplex)
Fast Ethernet: 100Mbps (half-duplex), 200Mbps (full-duplex)
Gigabit Ethernet: 2000Mbps (full duplex)
Network Cables 10Base-T: 2-pair UTP Cat 3, 4, 5 up to 100 meters.
100Base-T : 2-pair UTP Cat 5, 5e up to 100 meters.
1000Base-T: 4-pair UTP Cat5e 6, up to 100meters.
Number of Ports 8 x 10/100/1000Mbps auto-MDIX RJ-45 ports with 8 PoE enabled ports.
PoE power on RJ-45 Power +: pin 3 & pin 6 : Power –” pin 1 & pin 2.
AC to DC power
supply Input: 110V ~ 240VAC, 50Hz ~ 60Hz. Output: 48VDC 2.5A.
Power Consumption 8.0 watts ( max with no PD device connected)
107.8watts ( 7 PoE ports 15.4W/port)
Temperature Operation: 0℃~ 40 ℃or 32℉~ 104 ℉
Storage Temperature: -10℃~ 70 ℃or 14℉~ 158 ℉
Humidity Relative Humidity: 5% -95%
Dimensions 210 mm W x 171 mm D x 43.2 mm H
EMI FCC Class B, CE Mark Class B
Safety 100VAC to 240VAC power supply UL listed.
Filtering Address
Table 2K entries per device
Packet Filtering
Forwarding Rate 10Mbps Ethernet: 14,880/pps
100Mbps Ethernet: 148,800/pps
1000MBase-T Ethernet: 1,488,000/pps.
MAC address
Learning Automatic update
Transmission Method Store –and –Forward
8-Port Ethernet Gigabit PoE Switch Rev 1.0 12/01/2013 Page 6 / 7

8. Troubleshooting
1> After connecting the Switch to a power outlet, the LEDs do not turn on.
Check the connection of the power cord to the Router and the power outlet.
Check that the power outlet is receiving power.
2> When I connect a computer to the Switch's port, the Link/ACT LED turns on, but
the 100Mbps LED remains off.
When the 100Mbps LED is off, the computer's connection speed is 10Mbps.
3> After I connect my PCs to the Switch, I am unable to share files.
1. Check the LEDs on the Switch. Make sure the Link/ACT LED is on.
2. Check the network cable. The minimum length of the cable is 1.5 meters and the
maximum length of the cable is 100 meters.
3. Disable any software firewall program.
4. Verify that you have file sharing enabled. Please contact your Operating System
support for more information.
4> After I connect my PCs to the Switch, I can only get onto the Internet from one
computer.
The Switch was not designed to share Internet between multiple computers. You need to
get an Internet router.
5> Where is the uplink port located on the Switch?
Since all the ports on the Switch areAuto-MDIX, any of the ports can be used as an
uplink port. If you still encounter problems or have any questions regarding the 8-Port
Gigabit PoE switch please contact supplier’s Technical support department.
8-Port Ethernet Gigabit PoE Switch Rev 1.0 12/01/2013 Page 7 / 7