Ryobi CIDD18V2 Operation manual

18 VOLT COMPACT HAMMER DRILL DRIVER
OWNER’S OPERATING MANUAL
ORIGINAL INSTRUCTIONS
CIDD18V2
CIDD18V2_010099002_SAA_D3.indd A1CIDD18V2_010099002_SAA_D3.indd A1 10/25/2010 12:09:53 PM10/25/2010 12:09:53 PM

1. Keyless chuck
2. Torque adjustment ring
3. Quick mode selector
4. Two-speed gear train
5. Rotation selector (forward/reverse/center lock)
6. Bit storage
7. Switch trigger
8. Battery pack (Not included)
9. Latches
10. Depress latches to release battery pack
11. Reverse
12. Forward
13. Chuck jaws
14. Lock (tighten)
15. Unlock (release)
16. Low speed
17. High speed
18. Drive mode
19. Drill mode
20. Hammer mode
21. To increase torque
22. To decrease torque
23. Bit
24. Bit holder
25. Chuck sleeve
26. Drill bit
DESCRIPTION
Fig. 1
1
234
23
6
7
8
5
CIDD18V2_010099002_SAA_D3.indd A2CIDD18V2_010099002_SAA_D3.indd A2 10/25/2010 12:10:07 PM10/25/2010 12:10:07 PM

5
7
11
12
9
10
10
8
25
14
15
13
4
16
17
LO
HI
Fig. 2
Fig. 3
Fig. 4
Fig. 5
6
23 24
CIDD18V2_010099002_SAA_D3.indd A3CIDD18V2_010099002_SAA_D3.indd A3 10/25/2010 12:10:09 PM10/25/2010 12:10:09 PM

  

 

 

)LJ
)LJ
)LJ





CIDD18V2_010099002_SAA_D3.indd A4CIDD18V2_010099002_SAA_D3.indd A4 10/25/2010 12:10:15 PM10/25/2010 12:10:15 PM

Important!
It is essential that you read the instructions in this manual before
operating this machine.
Subject to technical modifications.
CIDD18V2_010099002_SAA_D3.indd A5CIDD18V2_010099002_SAA_D3.indd A5 10/25/2010 12:10:18 PM10/25/2010 12:10:18 PM

1
English
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result
in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1. WORK AREA
a. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power tools
create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. ELECTRICAL SAFETY
a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adaptor plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk
of electric shock.
f. If operating power tools in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
3. PERSONAL SAFETY
a. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medi-
cation. A moment of inattention while operating
power tools may result in serious personal injury.
b. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
c. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising power
tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
e. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
g. If devices are provided for the connection of
dust extraction and collection facilities, en-
sure these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
4. POWER TOOL USE AND CARE
a. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b. Do not use the power tool if the switch does
not turn it on and off. Any power tool that can
not be controlled with the switch is dangerous and
must be repaired.
c. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing ac-
cessories, or storing power tools. Such preven-
tive safety measures reduce the risk of starting
the power tool accidentally.
d. Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
CIDD18V2_010099002_SAA_D3.indd 1CIDD18V2_010099002_SAA_D3.indd 1 10/25/2010 12:10:18 PM10/25/2010 12:10:18 PM

2
English
hands of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tools operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits
etc., in accordance with these instructions and
in the manner intended for the particular type
of power tool, taking into account the working
conditions and the work to be performed. Use
of the power tool for operations different from
intended could result in a hazardous situation.
5. BATTERY TOOL USE AND CARE
a. Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
b. Use power tools only with specifically desig-
nated battery packs. Use of any other battery
packs may create a risk of injury and fire.
c. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery termi-
nals together may cause burns or a fire.
d. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If con-
tact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
irritation or burns.
6. SERVICE
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
SPECIAL SAFETY RULES
■Wear ear protectors. Exposure to noise can cause
hearing loss.
■Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
■Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
SPECIFICATIONS
Voltage 18 V
Chuck 2-13 mm
Switch Variable speed
No load speed (Drill mode):
-Lo speed 0-400 min-1
-Hi speed 0-1550 min-1
Hammer speed (Blows per minute):
-Lo speed 0-5200 min-1
-Hi speed 0-20150 min-1
Max. torque 40 Nm
Weight (not incl. battery pack) 1.38 Kg
MODEL COMPATIBLE BATTERY
PACK
COMPATIBLE
CHARGER
CIDD18V2
BPL-1820
BPL-1815
BCL-1800
BCS618
BCL1418
ABP1801
ABP-1815
ABP-1817
ABP-1813
BCL-1800
BCL1418
BCS618
ACR1800
260022029
OPERATION
WARNING
Do not allow familiarity with products to make
you careless. Remember that a careless fraction
of a second is sufficient to inflict serious injury.
WARNING
Always wear safety goggles or safety glasses
with side shields when operating products.
Failure to do so could result in objects being
thrown into your eyes, resulting in possible
serious injury.
WARNING
Do not use any attachments or accessories
not recommended by the manufacturer of this
product. The use of attachments or accessories
not recommended can result in serious personal
injury.
CIDD18V2_010099002_SAA_D3.indd 2CIDD18V2_010099002_SAA_D3.indd 2 10/25/2010 12:10:18 PM10/25/2010 12:10:18 PM

3
English
APPLICATIONS
You may use this product for the purposes listed below:
■Drilling in all types of wood products (lumber,
plywood, panelling, composition board, and hard
board)
■Drilling in ceramics, plastics, fiberglass, and laminates
■Drilling in metals
■Driving screws
■Hammer drilling in concrete, brick, or other masonry
This product will accept RYOBI One+ 18 V lithium-ion
battery packs and RYOBI One+ 18 V nickel-cadmium
battery packs.
BATTERY PROTECTION FEATURES
RYOBI 18 V lithium-ion batteries are designed with
features that protect the lithium-ion cells and maximize
battery life. Under some operating conditions, these
built-in features may cause the battery and the tool it is
powering to act differently from nickel-cadmium batteries.
During some applications, the battery electronics may
signal the battery to shut down, and cause the tool to
stop running. To reset the battery and tool, release the
trigger and resume normal operation.
NOTE: To prevent further shut down of the battery, avoid
forcing the tool.
If releasing the trigger does not reset the battery and
tool, the battery pack is depleted. If depleted, the battery
pack will begin charging when placed on the lithium-ion
charger.
TO INSTALL BATTERY PACK
See Figure 2.
■Lock the switch trigger by placing the rotation selector
in the center position.
■Place the battery pack on the tool.
■Make sure the latches on each side of the battery
pack snap into place and the battery pack is secured
on the tool before beginning operation.
WARNING
Always remove battery pack from your tool when
you are assembling parts, making adjustments,
cleaning, or when not in use. Removing battery
pack will prevent accidental starting that could
cause serious personal injury.
TO REMOVE BATTERY PACK
See Figure 2.
■Lock the switch trigger by placing the rotation selector
in the center position.
■Depress the latches on the side of battery pack.
■Remove the battery pack from the tool.
WARNING
Battery tools are always in operating condition.
Therefore, switch should always be locked when
not in use or when carrying at your side.
SWITCH TRIGGER
See Figure 3.
■To turn the drill ON, depress the switch trigger.
■To turn it OFF, release the switch trigger.
VARIABLE SPEED
The variable speed switch trigger delivers higher speed
and torque with increased trigger pressure and lower
speed with decreased trigger pressure.
NOTE: You might hear a whistling or ringing noise from
the switch during use. Do not be concerned; this is a
normal part of the switch function.
ROTATION SELECTOR
(FORWARD/REVERSE/CENTER LOCK)
See Figure 3.
The bit rotation is reversible and is controlled by a
selector located above the switch trigger. With the drill
held in normal operating position, the rotation selector
should be positioned to the left of the switch trigger for
forward drilling. The drilling direction is reversed when
the selector is to the right of the switch trigger.
Setting the switch trigger in the OFF (center lock) position
helps reduce the possibility of accidental starting when
not in use.
CAUTION:
To prevent gear damage, always allow the chuck
to come to a complete stop before changing the
direction of rotation.
To stop the drill, release the switch trigger and allow the
chuck to come to a complete stop.
NOTE: The drill will not run unless the rotation selector is
pushed fully to the left or right.
Avoid running the drill at low speeds for extended periods
of time. Running at low speeds under constant usage
may cause the drill to become overheated. If this occurs,
cool the drill by running it without a load and at full speed.
CIDD18V2_010099002_SAA_D3.indd 3CIDD18V2_010099002_SAA_D3.indd 3 10/25/2010 12:10:18 PM10/25/2010 12:10:18 PM

4
English
INTERNAL SPINDLE LOCK
The internal spindle lock allows the user single-handed
control of chuck adjustments and bit changes. Squeezing
the chuck body stops the chuck jaws from turning. For
bit changes and chuck adjustments, squeeze the chuck
body and turn.
KEYLESS CHUCK
See Figure 4.
The drill has a keyless chuck to tighten or release drill
bits in the chuck jaws. The arrows on the chuck indicate
which direction to rotate the chuck body in order to LOCK
(tighten) or UNLOCK (release) the drill bit.
WARNING
Do not hold the chuck with one hand and use the
power of the drill to tighten the chuck jaws on the
drill bit. The chuck body could slip in your hand,
or your hand could slip and come in contact with
the rotating drill bit. This could cause an accident
resulting in serious personal injury.
TWO-SPEED GEAR TRAIN (HI-LO)
See Figure 5.
The drill has a two-speed gear train designed for drilling
or driving at LO (1) or HI (2) speeds. A slide switch is
located on top of the drill to select either LO (1) or HI (2)
speed. When using drill in the LO (1) speed range, speed
will decrease and unit will have more power and torque.
When using drill in the HI (2) speed range, speed will
increase and unit will have less power and torque. Use
LO (1) speed for high power and torque applications and
HI (2) speed for fast drilling or driving applications.
NOTE: If you have difficulty changing from one gear
range to the other, turn the chuck by hand until the gears
engage.
CAUTION:
Never change gears while the tool is running.
Failure to obey this caution could result in
serious damage to the drill.
QUICK MODE SELECTOR
See Figure 6.
The Quick Mode Selector allows you to quickly switch
from drill mode to drive mode.
In general, drill mode should be used for drilling and
other heavy duty applications. Drive mode should be
used for driving screws.percussion mode should be used
for impact drilling.
TORQUE ADJUSTMENT
See Figure 7.
When using the drill-driver for various driving
applications, it becomes necessary to increase
or decrease the torque in order to help prevent the
possibility of damaging screw heads, threads, workpiece,
etc. In general, torque intensity should correspond to the
screw diameter. If the torque is too high or the screws too
small, the screws may be damaged or broken.
The torque is adjusted by rotating the torque adjustment ring.
The torque is greater when the torque adjustment ring
is set on a higher setting. The torque is less when the
torque adjustment ring is set on a lower setting.
The proper setting depends on the type of material and
the size of screw you are using.
BIT STORAGE
See Figure 2.
When not in use, bits provided with the drill can be
placed in the storage areas located on the base of the
drill.
SELECTING DRIVE OR DRILL SETTING
See Figure 5-6.
Using the chart below, choose correct speed and mode,
the type of bit, fastener, and material you will be using.
■Choose your APPLICATION
■Choose the correct SPEED: (1/LOW or 2/HIGH)
■Choose the correct MODE: (DRIVE, DRILL, OR
HAMMER)
CIDD18V2_010099002_SAA_D3.indd 4CIDD18V2_010099002_SAA_D3.indd 4 10/25/2010 12:10:18 PM10/25/2010 12:10:18 PM

5
English
1. APPLICATION 2. SPEED 3. MODE
• Lag screws up to 9.5 mm dia. by 38.1 mm long
• Hole saw up to 50.8 mm
• Spade bits up to 38.1 mm
• Drill bits up to 12.7 mm
• Drilling into metal
• Concrete screws
1/LOW DRILL MODE
(TORQUE ADJUSMENT NOT ACTIVE)
2/HIGH
• Drill bits up to 6.4 mm
• Deck or wood screws up to 63.5 mm long
• Self tapping screws
1/LOW DRIVE MODE
• Deck or wood screws up to 63.5 mm long
• Small screws or delicate work that requires more control 2/HIGH
• Masonry bit up to 12.7 mm
1/LOW HAMMER MODE
(TORQUE ADJUSMENT NOT ACTIVE)
2/HIGH
INSTALLING BITS
See Figure 8.
■Lock the switch trigger by placing the rotation selector
in the center position.
■Open or close the chuck jaws to a point where the
opening is slightly larger than the bit size you intend
to use. Also, raise the front of the drill slightly to keep
the bit from falling out of the chuck jaws.
■Insert the drill bit.
■Tighten the chuck jaws on the drill bit.
WARNING:
Make sure to insert the drill bit straight into the
chuck jaws. Do not insert the drill bit into the
chuck jaws at an angle then tighten. This could
cause the drill bit to be thrown from the drill,
resulting in possible serious personal injury or
damage to the chuck.
NOTE: Rotate the chuck body in the direction of the
arrow marked LOCK to tighten the chuck jaws. Do not
use a wrench to tighten or loosen the chuck jaws.
REMOVING BITS
See Figure 8.
■Lock the switch trigger by placing the rotation selector
in the center position.
■Open the chuck jaws.
NOTE: Rotate the chuck body in the direction of the
arrow marked UNLOCK to loosen the chuck jaws. Do
not use a wrench to tighten or loosen the chuck jaws.
■Remove the drill bit.
DRILLING
■Check the rotation selector for the correct setting
(forward or reverse).
■Secure the material to be drilled in a vise or with
clamps to keep it from turning as the drill bit rotates.
■Hold the drill firmly and place the bit at the point to be
drilled.
■Depress the switch trigger to start the drill.
■Move the drill bit into the workpiece, applying only
enough pressure to keep the bit cutting. Do not force
the drill or apply side pressure to elongate a hole. Let
the tool do the work.
WARNING:
Be prepared for binding at bit breakthrough.
When these situations occur, drill has a tendency
to grab and kick opposite to the direction of
rotation and could cause loss of control when
breaking through material. If not prepared, this
loss of control can result in possible serious
injury.
■When drilling hard, smooth surfaces, use a center
punch to mark the desired hole location. This will
prevent the drill bit from slipping off-center as the hole
is started.
■When drilling metals, use a light oil on the drill bit to
keep it from overheating. The oil will prolong the life
of the bit and increase the drilling action.
■If the bit jams in the workpiece or if the drill stalls,
stop the tool immediately. Remove the bit from the
workpiece and determine the reason for jamming.
CIDD18V2_010099002_SAA_D3.indd 5CIDD18V2_010099002_SAA_D3.indd 5 10/25/2010 12:10:18 PM10/25/2010 12:10:18 PM

6
English
NOTE: This drill has an electric brake. When the switch
trigger is released, the chuck stops turning. When the
brake is functioning properly, sparks will be visible
through the vent slots on the housing. This is normal and
is the action of the brake.
MAINTENANCE
WARNING
When servicing, use only identical RYOBI
replacement parts. Use of any other parts may
create a hazard or cause product damage.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may
result in serious personal injury.
Do not abuse power tools. Abusive practices can damage
tool as well as workpiece.
WARNING
Do not attempt to modify this tool or create
accessories not recommended for use with
this tool. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing
as waste. The machine, accessories
and packaging should be sorted for
environmental-friendly recycling.
SYMBOL
Safety Alert
V Volts
min-1 Revolutions or reciprocations per minute
Direct current
Please read the instructions carefully before
starting the machine.
Recycle unwanted
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.
CIDD18V2_010099002_SAA_D3.indd 6CIDD18V2_010099002_SAA_D3.indd 6 10/25/2010 12:10:19 PM10/25/2010 12:10:19 PM

TECHTRONIC INDUSTRIES (AUSTRALIA) PTY. LTD.
Level 1. 666 Doncaster Road,
Doncaster, Victoria 3108
Australia.
Tel: [phone] Fax No.: 613 9840 6133 www.ryobi.com.au
CIDD18V2_010099002_SAA_D3.indd 7CIDD18V2_010099002_SAA_D3.indd 7 10/25/2010 12:10:19 PM10/25/2010 12:10:19 PM