S.Wear Loop R8 User manual

R8

PACKAGE CONTENTS
1.Gift Box 2.Wireless Audio Receiver 3.a Manual
PRODUCT OVERVIEW
BUTTON CONTROL
a. Power On: When off, Press and hold the MFB for 2
seconds .
b. Power off: When on, Press and hold the MFB for 3
seconds .
c. Play/Pause: Press the MFB once in audio mode .

d. Volume+/-:Press the Volume+ or Volume- button once
e. Next /Previous Track: Press and hold the Volume+ or
Volume- button for 2 seconds .
f. Answering phone Call: When you receive an incoming call,
press the MFB button once.
g. End a phone call: During a call, press the MFB button
once .
h. Reject a phone call: When you receive an incoming call,
press and hold the MFB Button for 2 seconds .
i. Number Redial: Press the MFB button twice to redial the
latest phone number .
j.Paring Mode: When the loop R8 is off, Press and hold the
MFB button for 5 seconds until the LED indicator Flashes red
and blue ,activate BT on your phone and set it to search for
loop R8.
LED Indicators
LED Indicator
Status
Red -Solid
Charging
Blue-Solid
Fully Charged
Blue and Red-Flashing
In Paring Mode
Blue-Flashes every 2
Not paired with any device

seconds
Blue-Flashes every 5
seconds
Pairing with a device
Red-Flashing
Low Battery
Pairing with Two BT Devices at the Same Time
You can pair your loop R8 with two devices ,but only one of
them can play music or make phone calls with the R8 at any
time
1.)Follow the previous instructions in the ”Pairing “section
above to pair R8 to your first device.
2.)Turn off the BT function on your first device and follow the
paring instructions above again to pair to your second BT
device .
Note:
●The Receiver will remember previously paired devices and
will attempt to pair with the last connected device
automatically.
Safety and Care

1.)Although the Receiver are equipped with necessary
battery
regulators, it is recommended not to use Quick/Fast Chargers
which tend to over-charge the device and can reduce the
lifespan of the battery substantially.
2.)Do not charge R8 when they are Wet due to sweat or other
Moisture.
3.)Wipe away any excess sweat or moisture before and
during use, any prolonged exposure to sweat can corrode the
Liquipel coating and can penetrate through and damage
internal components.
4.)Keep the receiver away from extreme heat and humidity.
High heat will decrease the lifespan of the Receiver and
battery.
5.)The Receiver should be charged at least once every 6
months.
6.)Clean with a soft cloth, damp with diluted soap water
solution if necessary .Never use chemical cleaners.
7.)Do not drop the Receiver on hard surfaces.
8.)Do not take the Receiver apart
9.)When not use, power the Receiver off and store in a cool,
dry place.

10.)Overcharging or keeping the Receiver in a closed car or
similar environment for long periods will reduce the capacity
and life of the battery. It is not recommended to charge your
Receiver overnight.
WARING：
Using Receiver at high to moderate Volumes for extended
periods of time will result in permanent hearing damage .It is
advised you keep volume levels moderate to low at all times
for your safety.
It is advised to turn the volume on your device all the way
down before connecting your Receiver, then gradually
increase the volume Untill you reach a comfortable listening
level.
Troubleshooting：
Q: My Receiver will not turn on.
A: Please make sure your Receiver is recharged and has
enough power. Plug the Receiver to a charger and check if the
indicator becomes solid red.
Q: Pairing to a BT device doesn’t work.

A: Please do the following:
Make sure the Receiver is turned on and the LED indicator
is flashing blue and red.
Make sure the Receiver and the BT device are close to each
other within 3 feet.
Turn off the Receiver and the BT device, then turn on the
Receiver and then restart BT device. Then retry the pairing
method.
Make sure your Bluetooth device supports A2DP.
Q: After pairing, the Receiver disconnects or these is too
much background noise.
A: Please do the following:
Recharge your Receiver, the power may be too low.
Units are out of range (10 meters maximum). Bring units
closer together.
Remove any object (electrical or magnetic) that may be
interfering or blocking the signal between units.
Q: After pairing and connecting with my BT device, I can not
hear music/audio.
A: Please check the following:

Your BT device is connected to Receiver. The LED indicator
should flash blue once every 5 seconds.
Make sure the volume is at an audible level on both your
Receiver and the BT device.
Make sure the BT device is playing music/audio.
Q: The LED indicator does not show solid red when charging
the Receiver.
A: The Receiver has been discharged for too long. Leave the
unit on charge for about 30 minutes and the LED indicator
should show solid red.