Sab Satellite Titan III Combo HD User manual

1
CONTENTS
1. SAFETY .....................................................................................................................................................3
2. INTRODUCTION......................................................................................................................................3
3. FEATURES................................................................................................................................................4
4. REMOTE CONTROL ...............................................................................................................................5
5. FRONT PANEL.........................................................................................................................................7
6. REAR PANEL............................................................................................................................................7
7. CONNECTING YOUR SYSTEM..............................................................................................................8
7.1 TV WITH MOTORIZED SYSTEM (DISEQC1.2).............................................................................................8
7.2 CONNECTING THE NETWORK......................................................................................................................9
8. BASIC OPERATIONS.............................................................................................................................10
8.1 TURN ON STB .........................................................................................................................................10
8.2 POWER....................................................................................................................................................10
8.3 CHANNEL UP/CHANNEL DOWN ................................................................................................................10
8.4 VOLUME UP/VOLUME DOWN-..................................................................................................................10
8.5 NUMBER .................................................................................................................................................10
8.6 MUTE......................................................................................................................................................10
8.7 PAUSE.....................................................................................................................................................10
8.8 RECALL...................................................................................................................................................10
8.9 FAVORITE................................................................................................................................................10
8.10 AUDIO .................................................................................................................................................11
8.11 INFORMATION ......................................................................................................................................11
8.12 EPG .................................................................................................................................................... 11
8.13 TV/RADIO .........................................................................................................................................12
8.14 CHANNEL LIST.....................................................................................................................................12
8.15 SLEEP ..................................................................................................................................................13
8.16 PAGE UP/PAGE DOWN ..........................................................................................................................13
8.17 TEXT..................................................................................................................................................14
8.18 SUBTITLE.............................................................................................................................................14
8.19 FIND ....................................................................................................................................................14
8.20 ZOOM ..................................................................................................................................................14
8.21 TV/SAT ............................................................................................................................................... 14
8.22 MENU..................................................................................................................................................14
8.23 VIDEO FORMAT....................................................................................................................................14
8.24 EXIT .................................................................................................................................................... 14
9. SERVICE..................................................................................................................................................15
9.1 ORGANIZING SERVICE..............................................................................................................................15
9.2 ORGANIZING FAVOURITES .......................................................................................................................17
10. INSTALLATION.....................................................................................................................................17
10.1 SATELLITE INSTALLATION ....................................................................................................................17
10.2 FASTSCAN SATELLITE ..........................................................................................................................19
10.3 AUTO INSTALLATION............................................................................................................................ 19
10.4 SATELLITE GUIDE ................................................................................................................................ 19
10.5 TERRESTRIAL INSTALLATION................................................................................................................20
10.6 CABLE INSTALLATION ..........................................................................................................................20
11. SYSTEM...................................................................................................................................................21
11.1 LANGUAGE ..........................................................................................................................................21
11.2 A/V CONTROL .....................................................................................................................................22
11.3 ETHERNET SETTING..............................................................................................................................22
11.4 TIME SETTING......................................................................................................................................23
11.5 TIMER..................................................................................................................................................24
11.6 PARENTAL CONTROL............................................................................................................................25

2
11.7 MISCELLANEOUS SETTINGS ..................................................................................................................25
11.8 SOFTWARE UPGRADE ........................................................................................................................... 26
11.8.1 Upgrade By USB.............................................................................................................................. 26
11.8.2 Http Upgrade...................................................................................................................................26
11.8.3 Ftp Upgrade.....................................................................................................................................26
11.8.4 Upgrade by RS232:.......................................................................................................................... 26
11.8.5 Backup to USB.................................................................................................................................27
11.9 DEFAULT SETTING ...............................................................................................................................28
11.9.1 Default Value:..................................................................................................................................28
11.9.2 Delete All Channel:.......................................................................................................................... 28
11.9.3 Save default value ............................................................................................................................ 29
11.10 INFORMATION ......................................................................................................................................29
12. CONDITIONAL ACCESS.......................................................................................................................29
12.1 CA SETTING ........................................................................................................................................29
12.2 COMMONINTERFACE ....................................................................................................................30
13. MEDIA.....................................................................................................................................................30
13.1 RECORD...............................................................................................................................................30
13.2 MOVIE.................................................................................................................................................30
13.3 MUSIC .................................................................................................................................................31
13.4 IMAGE .................................................................................................................................................32
13.5 PVR SETTING ......................................................................................................................................34
13.6 DISK MANAGE .....................................................................................................................................34
13.7 REMOVE USBDEVICE SAFELY! ............................................................................................................35
14. APPLICATION........................................................................................................................................35
14.1 YOUTUBE.............................................................................................................................................35
14.2 RSS READER .......................................................................................................................................36
14.3 WEATHER FORECAST ........................................................................................................................... 37
14.4 GOOGLE MAPS.....................................................................................................................................37
14.5 FTP.....................................................................................................................................................37
14.6 WEB TV .............................................................................................................................................. 37
15. GAME.......................................................................................................................................................38
15.1 TETRIS.................................................................................................................................................38
15.2 SNAKE .................................................................................................................................................38
15.3 OTHELLO .............................................................................................................................................38
16. EPG...........................................................................................................................................................38
17. NEW FEATURES....................................................................................................................................39
17.1 EQUALIZER ..........................................................................................................................................39
17.2 TIME SHIFT ..........................................................................................................................................39
17.3 RECORD...............................................................................................................................................39
18. TROUBLE SHOOTING..........................................................................................................................41
19. SPECIFICATIONS..................................................................................................................................42

3
1. SAFETY
This HD Receiver has been manufactured to satisfythe international safety standards. Please read the following safety
precautions carefully.
MAINS SUPPLY:
100~2
4
0V AC, 50/60Hz
OVERLOADING
: Do not overload wall outlet, extension cord or adapter as this may result in fire or
electric shock.
LIQUIDS:
Keep liquids away f
rom the
HD Receiver
. The apparatus shall not be exposed to dripping
or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
CLEANING:
Disconnect the
HD Receiver
from the wall outlet before cleaning .Use a l
ight damp cloth
(no solvents) to dust the HD Receiver.
VENTILATION:
The slots on top of the
HD Receiver
must be left uncovered to allow proper airflow to
the unit. Do not stand the HD Receiver on soft furnishings or carpets. Do not expose the HD Receiver
to direct sunlight or do not place it near a heater. Do not stack electronic equipments on top of the
HD
Receiver.
ATTACHMENTS:
Do not use any attachments that are not recommended as these may cause
hazard or damage the HD Receiver.
CONNECTION TO T
HE SATELLITE DISH LNB:
Disconnect the
HD Receiver
from the mains before
connecting or disconnecting the cable from the satellite dish.
FAILURE TO DO SO CAN DAMAGE THE LNB.
CONNECTION TO THE TV:
Disconnect the
HD Receiver
from the mains before connecti
ng or
disconnecting the cable from the satellite dish.
FAILURE TO DO SO CAN DAMAGE THE TV.
EARTHING:
The LNB cable MUST BE EARTHED to the system earth for the satellite dish.
LOCATION:
Place the
HD Receiver
indoor in order not to expose to lightening
, rain or sunlight.
2. INTRODUCTION
Thank you for purchasing the HD Receiver.
This HD Receiver is fully compliant with the international DVB standard and thus transmits digital images, sounds,
information guides and teletext directly to your TV through the satellite broadcasting.
Now you can comfortably see and receive digitally transmitted music, news, movie and sports satellite broadcasts in
your office or at your home. You can enjoy interesting games embedded in HD Receiver.
In service search section, both the automatic service search method and themanual search mode are provided. Also it
supports DiSEqC 1.0, 1.2 and USALS, enabling you to move your antenna in order to focus preferred satellite. You
can save up to 6000 TV and Radio services and work around with the favorite, Lock, Delete, Move and Sort functions.
The menu is very modern and supports multiple languages. All functions can be carried out using the remote control
and some of the functions can also be carried out using the front panel. The HD Receiver is easy to use and adaptable
for future advances. Please be aware that new software may change the functions of the HD Receiver.

4
If you have any difficulties concerning the operation of your HD Receiver, please refer to the relevant section of this
manual, including the ‘Troubleshooting’. This Manual will provide you with useful information on using the HD
Receiver.
3. FEATURES
MPEG-Fully DVB-S / DVB-S2 (H.264) HD compliant
6000 channels (TV and Radio) programmable
Multilingual menu text support
Channel switching time less than 1 second
Channel list editing
Favorite channel list editing
True-color On-Screen Display (OSD)
Full Picture In Graphic (PIG) function
Electronic Program Guide (EPG) for on screen channel information
Subtitle supported
Teletext supported by VBI insertion and software emulation
Parental lock facility by channel and program event
Program and Channel information transfer from receiver to receiver
Exciting games embedded
Dolby Digital Bit-Stream output via HDMI
DiSEqC 1.0, 1.1, 1.2 ,USALS and Unicable
HDMI Full HD (1080p) Video/Audio Output
2x USB 2.0 Host
RTC (Real-Time-Clock)
Time Shift
Video Recording
Recording one channel and Time Shifting another channel (optional)
3G Network Function Supported

5
4. Remote Control
You can power on/off the receiver, operate on screen menu, and use a
variety of hot key function.
POWER
To switch your receiver on from standby or standby to on.
MUTE
Used to enable or disable the audio
NUMERIC KEYS
Used to select channels or enter programming parameters
TV / RADIO
Receiver switches between TV and Radio mode.
(ZOOM)
Press key select zoom times, from X1 to X16.
RECALL
Return to the previous menu or status.
TV/SAT
Receiver switches between TV and receive mode.
INFO
To display channel status or various program information of current service.
EPG(Electronic Program Guide)
Display the Programs guide on screen when available.
MENU
Displays the Main Menu on the screen, or return to the previous menu or
status.
EXIT
Cancel the user selection and return to the viewing mode from a menu.
OK
To select menu option, or to updated on entry.
<,> KEY
To adjust volume level, or to move cursor left or right in the menu.
^,v KEY
To change channels, or to move cursor up or down in the menu.
PAGE /PAGE
To move up the cursor to the next or previous page
in the menu or channel list.
●REC
Has different functions per menu.
Teletext
Shows teletext information of the current channel supports.
Subtitle
Subtitle Display.
UHF
In case your TV is connected through RF Modulator (UHF), select output
channel number between CH21 and CH69 with up and down key.
(FIND)
Use to prompt find channels sort by character.
TIMER
Press timer key you can setup up the Standby time.
V ． FORMAT
Press V.FORMAT button to switch the display mode among "AUTO", "By
Native TV","480p", "576P", "720P_50","720P_60,"1080i_50"," 1080i_60" ,"
1080P_50" and" 1080P_60"
FAV(FAVORITE)
To set receiver to the favorite server mode,
display the favorite channel.
FOLDER
Press this button to enter the Record Manager menu directly.
AUDIO(Red Key)
Audio channels setup, to select audio mode; Left, Right , Stereo, Mono.
OPTION(GREEN KEY)
Shows NVOD information of the current channel supports.
SAT
Display the satellite list at normal picture.
Play Mode
Select the play mode in MP3 or JPEG player.

6
USB
To remove the USB Hard Disk safely.
TMS(Time Shift)
Press this button to display Time Shift info bar.
Play
To play the MP3, JPEG, or Record files.
Stop
To stop the Time Shift, recording, or MP3/JPEG player.
PAUSE
Used to select the freeze function.
Press once to freeze the screen picture.
FB
To start Fast Backward function.
FF
To start Fast Forward function.
SB
To start Slow Backward function.
SF
To start Slow Forward function
/ PREV/NEXT
Switch to preview or next file in play mode

7
5. Front panel
POWER KEY: To switch the receiver power on/stand by.
MENU KEY：To enter the Main Menu.
EXIT KEY:
OK KEY: To see TV/Radio channel list, or to confirm in themenu.
V-/V+ KEY: To adjust volume level, or to move cursor left or right in the menu.
P-/P+ KEY: To change channels, or to move cursor up or down in the menu.
Remote Sensor: Detects infrared signal from remote control unit.
POWER Indicator: Lit whilst the receiver is powered on and at standby mode.
Signal Indicator: When received signal is strong, the signal indicator is lit.
Card Slot: One CA Interface for Conax.
Common Interface: One socket for Conditional Access Modules CAM.
USB : USB 2.0 Host, connect to USB hard disk, or flash disk,and 3G dongles.
Display: (LED type) Indicates operating status of receiver.
6. Rear Panel
Please refer to the diagram above for all possible connections of your receiver
Do not connect the unit to the mains socket until all other connections have been made and checked.
LNB IN 13/18V 400mA MAX: This port is to connect the coaxial cable from LNB of your Dish.
RF IN: This port is to connect the coaxial cable from Terrestrial/Cable Antenna.
S/PDIF: Digital Audio interface, connect to AV amplifier S/PDIF input terminal.
USB: USB 2.0 Host, connect to USB hard disk, or flash disk,and 3G dongles.
VIDEO OUT: This RCA connector is used to connect any external video.
AUDIO R/L: These RCA connectors are used to connect any external audio amp or system.
0/12V 50mA: This is used to connect 12V to an external 0V/12V switch.
HDMI: Audio and Video output socket for TV set with HDMI Input Jack only.
RS 232 SERIAL PORT: This is used to connect your receiver to a computer through a serial cable.
Ethernet: Network port, you can get a new software updates from this port.
POWER ON/OFF SWITCH: To switch ON/OFF the receiver power supply.

8
7. Connecting Your System
There are two ways to connect the receiver to your existing TV system. We recommend using one of the following
cases for the best result:
1. If you have a high definition television set, you should use a HDMI cable for best result, Plug oneend of the cable
into the HDMI socket on the receiver, and the other end into thematching socket on your television. In this
case, you do not have to make audio connections because the HDMI connector can output stereo audio or Dolby
Digital audio.
2. Connect one end of RCA cable to the RCA jack on the back of the receiver and the other end to a RCA jack on
your TV.
Finally connect the coaxial cable from the LNB of your Dish to the LNB IN jack on the receiver.
With External Audio / Hi-Fi System
To connect any external Audio Hi-Fi system, the receiver has been provided with RCA connector at the back of the
receiver marked with AV OUT.
Connect an RCA cable from the AV OUT jack on the back of the receiver to the LINE, AUX, SPARE OR EXTRA input
jacks on your Hi-Fi System.
7.1 TV with Motorized System (DiSEqC 1.2)
Connect one end of your coaxial cable to the LNB IN connector on the receiver and the other end to the REC or
Receiver connector on the DiSEqC 1.2 motor.
Connect the coaxial cable from the LNB to the LNB connector on the DiSEqC 1.2 motor.
All our receivers are designed to be DiSEqC 1.0 and DiSEqC 1.2 compatible.
This allows multiple antennas to be connected to the receiver at the same time.
If you have two or more fixed antennas or LNBs, then we recommend you use a DiSEqC 1.0
switch.
Connect the coaxial cable from the first LNB to the LNB 1 or LNB A input connector of the DiSEqC switch.
Do the same for any other LNBs that you have.
Connect one end of a coaxial cable to the RF output connector of the DiSEqC switch,

9
connect the other end to the LNB IN socket on the receiver.
To the digital receiver, you can connect either a single satellite antenna directly or LNB of
multi-feed equipment.
7.2 Connecting the Network
1. Connecting to the LAN:
Connect one end of the Ethernet cable to the product and the other end to the LAN router.
2.Connecting to the Wi-Fi (Wireless LAN):
You can connect the network via theWi-Fi access point or DSL/cable modem.
a. Plug in the wireless USB dongle to the USB port.(Separate purchase required)
b. Set the options for the Wi-Fi.
1. Network Name (SSID): Select the network name of your Wi-Fi access point from the list.
2. Security Type (WEP): This product supports WEP 40/128bit ASCII and WEP 40/128bit HEX. The security
type of the Wi-Fi and the product shall be set the same.
3. Password:When using the security type, you must set the password. Enter the same password in the Wi-Fi
setting menu.
3. Connecting to the 3G:
Connect the network via the 3G dongle. Plug in the USB that has 3G dongle.
Note: 1) Make sure the distance between theWi-Fi access point and the product is not toofar away. This may lower
the quality of service.
2) It is recommended to purchase a wireless USB dongle distributed by RT5370. Other products may not
function or respond.
3) It is recommended to purchase a 3G USB dongle distributed by huawei E1750 , E1550 , E1752 , E173
Other products may not function or respond.
4) We recommend the network connection over a direct LAN.

10
8. Basic Operations
8.1 Turn on STB
First, connect to an external 12V adapter to turn on
the unit.
When the STB is first used, there will play the first
channel from the default Channel List. If the STB is not
first used, STB will play the same channel as last time
before turning off.
?Frequently Asked Question
Q: The power of my STB has been turned on and not
in Standby mode, but the TV screen showed
nothing:
A: Make sure the TV set has been set to the correct
video input (not the TV channels). For example, if you
have connected the unit with the Video1 input of the TV
set, the TV set has to be switched to Video1.
Q: The power of my STB has been turn on and not in
Standby mode, but the TV screen showed
nothing except one box with “No Signal” image.
A: That means the channel, which you select, is no
signal. It could be several causes:
1 The channel which you select is not in your
allocate satellite. The simply solution is to change
channel.
2 The signal of current TV channel is too weak. You
can try to change channel to other strong signal
channels. If the problems still exist, please consult
your local dealer or other professionals for
technical service.
3 You use the Dual LNB, and you need Modify LNB
Type
8.2 Power
1 Press [Power] Key can enter the Standby state
2 In Standby state, press [Power] Key again can call
back the unit and go on play the previous channel
3 User can also disconnect the device’s main power
to end the Standby state.
8.3 Channel Up/Channel Down
In full screen, press [CH+/CH-] to change channel.
8.4 Volume Up/Volume Down-
In full screen, press [VOL+/VOL-] to adjust volume.
8.5 Number
In full screen, use number key and press [OK] on the
Remote Control Unit to change channel.
8.6 Mute
1 Press [MUTE] key to mute the sound and the
screen will show up mute OSD.
2 Press [MUTE] key again to restore sound.
8.7 Pause
1 In playing mode, press [Pause] key, the picture will
be paused, but the sound of the channel will still
continues.
2 Press [Pause] key again, the screen’s picture will
skip over to the current playing picture, and the
sound of the channel will corresponding playing.
8.8 Recall
Press [RETURN] key will directly switch to the
previous channel that you played before current
channel.
8.9 Favorite
1 In full screen, press [FAV] key, it will display a
window of “Favorite list” on the left of the screen,
which you can watch like below.
2 In the window of " Favorite list ", you can move
highlight by press [Channel Up/Channel Down]
key to select favorite Channels.

11
3 In the window of ” Favorite list ", you can press
[Left/Right] key to select favorite groups Pressing
[P-/P+] keys can implement the “Page up/Page
down” function
4 Press [Exit] key to exit the current window.
? Frequently Asked Question
Q: Why the screen displays “No Favorite Channel”,
after pressing [FAV] key?
A: It is because that you haven’t set any channels as
“favorite channel”. Please refer to Favorite
.
8.10 Audio
1 In full screen, press [AUDIO] key can open the
“Audio” window on the screen.
2 You can modify the audio track by press [Channel
Up / Channel Down] key and modify the audio
mode by press[left/right] key.
3 Mode: Left/Right/Stereo/Mono
8.11 Information
In full screen, press [INFO] key (press [INFO] key and
[RED] key) can open information screen, in the
window shows the parameters of current channel.
8.12 EPG
1 The STB has an Electronic Program Guide (EPG)
to help you navigate channels through all the
possible viewing options. The EPG supplies
information such as channel listings and starting
and ending times for all available channels.
Press [EPG] key to display EPG screen.
2 Press [Red] key can select the channels by
different group, such as by
Favorite/Satellite/Provider/CAS etc.
3 Press [Green] key to select different display mode
among Now EPG, Next EPG, More and Schedule,
like the following picture:

12
4 Press [Yellow] key in EPG menu can set one
record timer or go to Timer List menu.
5 In EPG menu, when you select one event by high
light item, you can set this event to record timer list
directly by press [REC] button.
6 In EPG menu, press [Exit] to close EPG screen.
8.13 TV/RADIO
In TV mode, pressing [TV/RADIO] key can switch to
Radio mode. In Radio mode, press [TV/RADIO] key to
switch to TV mode.
8.14 Channel List
1 In full screen, press [OK] key can enter “Channel
List”.
2 Press [Red] key to change the different group.
Which you can watch like below.

13
3 Press [Green] key to display details information for
EPG Now.
4 Press [Yellow] key you can changethe current
channel’s property, such as FAV/ Lock/ Skip/
Delete/ Rename.
5 Press [Blue] key can open the “Sort” windowlike
below. There are five kinds of sorting ways. You
can press [Channel Up/Channel Down] key to
move highlight and press [OK] key to confirm you
selection.
6 The five kinds of sorting way are:
Default: Sorting by scanning result.
FTA/$: Sort channel through free and
scramble sequence. Free channel will in the
front of channel list and scramble channel will
at the rear of channel list
Lock: Accumulated all locked channels and
list in the last of TV Channel List.
Name (A-Z): Sorting in Alphabetical Order,
ignore “$” symbol.
Name (Z-A): Sorting in Alphabetical Order,
ignore “$” Symbol.
7 Press [Up/Down] key to move highlight and press
[OK] key to play the highlighted channel.
8 Press [Page Up/Down] key to page up and page
Down.
9 Press [Exit] key to exit the channel list.
8.15 Sleep
1 This function can set sleep timer. When you set a
sleep timer and the time arrive, the system will
enter to standby automatically.
2 Pressing [SLEEP] key, it will switch the mode
between Sleep Timer Off /10/30/60/90/120
minutes.
8.16 Page Up/Page Down
In Channel list, press [Page+/Page-] key can page up
and page down the channel list.

14
8.17 TEXT
1 Press [TTX] key in full screen, you can open
teletext page on the channel which has teletext
information.
2 If the channel has no teletext information, it will
show “No Teletext Data” on the screen.
8.18 Subtitle
1 Press [SUBTITLE] key in full screen you can select
the subtitle language or off on the channel which
has subtitle.
2 If you set the Auto subtitle option as ON in
Miscellaneous settings menu, the subtitle will be
showed automatically.
8.19 Find
1 Press[Find] key in full screen can open the “Find”
window like above. You can
press[Up/Down/left/right ]key to move
highlight and press[OK]key to input the
selected symbol or letter into the dialogue.
2 After input each character, the program list
on the left will search the channel
according your input, and list the matched
channel.
3 Move highlight to “OK”and press [OK]
key can close“Find”window and you can
select channel from the channels list
directly.
8.20 Zoom
1 The [ZOOM] key allows you to magnify a certain
area on the images
2 Press [ZOOM] key again, the image will enlarge
rotate as x1, x2, x4, x6, x8, x12, x16.
3 In “x2 ~ x16” image, using [Up/ Down/ Up/ Down]
keys to move the image center area you want to
see.
4 In zoom mode, press [Exit] to close “Zoom”
window.
8.21 TV/Sat
Press [TV/Sat] key can switch between TV mode and
STB mode
8.22 Menu
Press [MENU] key can open themenu, exit the current
menu to last menu or close the window.
8.23 Video Format
Press [V. Format] key under Full Screen playback for
1st, it will show the current system outputting video
resolution, continuously press this key, system will
switch its outputting video resolution by sequence
“ 480i-> 480P-> 576i-> 576p-> 720P-> 1080i->1080p”.
8.24 Exit
1 Press [EXIT] key can exit the current menu to last
menu or close the window.

15
9.Service
When you press [Menu] key to enter menu, there will
display the picture like below:
1 Press[Left/Right] key you can select the submenu
of Organizing services and Organizing favourites.
2 Press [OK] key to enter the “Organizing Service”. If
Menu Lock is “On”, it will display an dialogue for
user to key in password. The default Password is
“0000”.
3 Press [Menu] key to go back to main menu.
9.1 Organizing Service
When you enter to “Organizing Service” menu, there will
display the screen like below.
1 You can move highlight by press [Channel
Up/Channel Down] key and [OK] key to select the
programs which you want to edit.
2 You can press [Page Up/Page Down] key to
implement the Page Up/Page Down function.
3 You can use [Red] key to switch different Group.
4 You can press [Green] key to select the programs
by different select mode.
5 Press color key can implement the corresponding
function in “Organizing Services”.
Groups
1 Press [Red] key can open the “Groups” window
like above
2 You can press [Up/Down] key to move highlight
and press [OK] key to select group.
3 Press [Menu] key to close “Groups” List.
Options
1 Press [Green] key can open the “Options” window
like above.
2 You can press [Up/Down] key to move highlight
and press [OK] key to confirm the select mode.
3 Press [Menu] key to close “Options” List.
Move

16
1 Select the channels which you want to edit in
channel list by press [OK] key or other select
mode.
2 Then press [Right] key to move the high light to
right toolbar.
3 Select Move icon by press [Channel Up/Channel
Down] key and [OK] key.
4 Move the channels to the position which you want
and press [OK] key to confirm. Like the following
picture:
Lock
1 Select the channels which you want to edit in
channel list by press [OK] key or other select
mode.
2 Then press [Right] key to move the high light to
right toolbar.
3 Select Lock icon by press [Channel Up/Channel
Down] key and [OK] key.
4 Lock the channel by press [OK] key.
Like the following picture:
Delete
1 Select the channels which you want to edit in
channel list by press [OK] key or other select
mode.
2 Then press [Right] key to move the high light to
right toolbar.
3 Select Delete icon by press [OK key to delete
channel one by one.
4 When you high light in channel list ,you can press
[OK] key to select more channels ,and repeat b
and c step to deleted.
Skip and rename
Follow the same way you can set the channel’s Skip or
give the new name for high light channel.
Find
1 Press[Find] key can open the “Find” window like
above. You can press[Up/Down/left/right]key to
move highlight and press [OK] key to input the
selected symbol or letter into the dialogue.

17
2 After input each character, the program list on the
left will search the channel according your input,
and list the matched channel.
3 Move highlight to “OK” and press [OK] key can
close “Find” window and you can select channel
from the channels list directly.
9.2 Organizing Favourites
This menu is helpful in adding and deleting services to
and from the favorite group.
1 FAV List
To choose the FAV List by press “FAV” button.
2 Add
To add services into favorites, Mark the desired services
by press “ OK ” button in Service List, press to
choose Add mode and press “ OK ” button.
3 Remove
To remove services from favorites, Mark the desired
services by press “ OK ” button in Favorite List, press
to choose Remove mode and press “ OK ” button.
4 Move
You can reorder and move the service to the preferred
position in Favorite List.
5 Rename
Select the desired FAV List by press “FAV” button, using
, buttons to choose Rename mode and press
“ OK ” button to display keyboard, and rename it.
6 Group, Options and Find functions
Please refer to the “Organizing Services” part in this
manual.
10.Installation
1 Press [Left/Right] key to select menu pages
among Satellite Installation,FastScan
Satellite,Auto installation,Satellite
Guide,Terrestrial Install,Cable Installation.
2 Press [OK] key to enter the “Installation”. If Menu
Lock is “On”, it will display an dialogue for user to
key in password. The default Password is “0000”.
3 Press [Up/ Down] key to select menu items. Press
[menu] key to go back to main menu.
10.1 Satellite Installation
Satellite
1 Satellite: Press[OK]key to enter the Satellite list.
2 Press [Up/ Down] key to select satellite. Press
[Page] key to page up or page down.
LNB Type
In this item, press[Left/Right]key can switch among
“Standard”, “User” and “Universal” , ”Unicable” mode.

18
DiSEqC
DiSEqC: You can press [OK] and [Up/ Down] key to
switch options. There are several options for your
selection:
a) Disable: without DiSEqC.
b)1/2, 2/2: two ports DiSEqC
c)1/4, 2/4, 3/4, 4/4: 4 ports DiSEqC
d)1/8, 2/8… 8/8: 8 ports DiSEqC
e)1/16, 2/16….16/16: 16 ports DiSEqC
Positioner
Positioner：In “Positioner” item, you can press
[Left/Right]key to switch “Off / DiSEqC 1.2 / USALS”
functions.
22K
You can use [Volume Up/ Volume Down] key to switch
“ON / Off”. When this item is switched to “ON”, receiver
will receive TV and radio input signal from 22K port. If
the item is switched to “Off”, the receiver will receive all
signal from 0K port.
!Notice
When you choose LNB type “Universal”, you can not
modify 22K.
Polarity
In “Polarity” item, [Left/Right]key to switch “Auto / H / V”
functions.
LNB Power
In “LNB POWER” item, you can press [Left/Right] key to
switch: ” On/Off” functions.
TP Edit
When you enter to “TP Edit” menu, there will display the
screen like below:
1 In “Satellite” item, press[Left/Right]key to switch
satellite that you want to scan or press[OK]key to
enter satellite list for selection.
2 In “TP Index” item, you not only can use
[Left/Right]key to select transponder but also can
use[Add] and [Delete]functions.
When you press[Green] key, it will display “New
TP” in “TP Index” item; You should set the
parameters of “TP Frequency” and “Symbol Rate”
for this new transponder. The parameters of “TP
Frequency” and “Symbol Rate” can set by number
keys. The available range are “3000~13450 MHz”
and “1000~45000Ks/s”.
When you press[Yellow] key, there will show up a
warning message for reminding whether you will
delete the current transponder or not. If you select

19
“Yes”, the current transponder will be deleted, and
the total account of transponder will reduce 1
correspondingly.
When you press [Blue] key, there will show up a
warning message for reminding whether you will
delete all transponders or not. If you select “OK”,
all transponders will be deleted.
3 For the existed transponder, you also can use
number keys to modify the parameters of “TP
Frequency” and “Symbol Rate”.
4 When you complete your modification, Press [Red]
key, it will show up a dialog to ask you scan mode,
program type, scan type and NIT Search on/off.
After you set up, press [OK] key to start scanning.
5 In the “TP Scan” item, press [Exit] key to exit the
scanning and save the current parameters.
Single Scan
1 Press [Red] key, it will show up a dialog to ask you
scan mode (means you want to scan all channels
or only scan free channels), program type (means
you want to scan all channels or only scan
TV/Radio channels), scan type (means preset
scan, that is searching the existed TP. Automatic
Scan means blind scan. It is no need existed TP
info) and NIT Search on/off. After you set up, press
[OK] key to start scanning.
2 Press [White] key into the blind scanning
immediately.
TP Scan
Press [Green] key to scan current TP’s programs.
Auto DiSEqC
Press [Blue] key to run Auto DiSEqC function, it can find
the satellite connect to which port automatically.
Blind Scan
Press [White] key can directly into blind scan mode to
scan the current satellite.
10.2 FastScan Satellite
In this menu, you can search the channels fast by select
the provider and press OK button on Start Search item.
10.3 Auto installation
“Auto Installation” is a very new and convenient function.
It will automatically detect all dishes connecting to this
machine and scan the available services belonging to
the satellite matched according to satellites and
transponders data in current database. You don’t have
to input any parameter of your antenna settings. Just
press “ OK ” button to enter this “Auto Installation” menu
then it starts scanning and shows you the result at the
end of scanning.
10.4 Satellite Guide
When you enter to “Satellite Guide” menu, you will see
the screen like below:

20
“Satellite Guide” is use for user to enter local longitude;
local latitude and satellite longitude. By the evaluation
from the receiver evaluate the antenna azimuth and
antenna elevation; user can follow this guidance to
adjust antenna.
1 You can use number keys to input parameters in
“Local Longitude”, “Local Latitude” and “Satellite
Longitude”.
2 You can use [Left/Right] key to select east or west
in “Local Longitude” and “Satellite Longitude”,
select north and south in “Local Latitude”.
3 Moving highlight to “Start” item and press [OK]
key. The lower column on the screen will calculate
the corresponding value automatically.
4 Orientation means the angle between south and
satellite.
5 Press [Exit] key to draw back to “Main” Menu.
10.5 Terrestrial Installation
Press [OK] key to enter the selected item.
1 You can select the Bandwidth according different
country.
2 You can set the Tuner Power ON/OFF.
3 Press [Red] key can directly into blind scan mode
to scan the current programs.
4 Press [Green] key to enter the following menu.
Scan Mode.
1 There are two modes. You can scan channel
bychannel or by frequency”.
2 When scan bandis UHF and region is “France”,the
range of Ch No. is from 21 to 69. When scan
3 band is VHF and region is “France”, the range of
Ch No. is from 1 to 9. (it’s according to region)
4 Press [Red] key to enter blind scan menu, or press
[Green] key to enter TP scan menu.
5 Press [Exit] key to exit the scanning.
10.6 Cable Installation
Press [OK] key to enter the selected item.
1 You can select the Scan Mode, Manual Scan or
Blind Scan.