Sabinetek SmartMike Classic User manual

Bluetooth Microphone
SmartMike Classic
Product Model:S630

Downloading the app
To utilize all functions of the device, please download the MetAudio app.
Method 1：Search MetAudio in the Apple/Google Play store
Method 2：Scan the below QR code to download

SmartMike Classic x1
Earpiece x1
USB-C Charging Cable x1
Windfoam x1
Deadcat x1
Instruction Manual x

Product Specifications
Weight: 14 g
Bluetooth Chipset: Qualcomm CSR
Bluetooth effective distance: 15m
Microphone Type: Omnidirectional condenser mic capsule
Recording Bandwidth: 20Hz-20KHz
Sampling Frequency: 44.1KHz
Frequency range: 20Hz-20KHz
Built-in battery: 115 mAh
Charge time: <2 hours
Input voltage: 5V
Charging port: USB-C

Device Instructions
Turn on：
While powered off, hold for 3s to turn on and enter pairing state.
Turn off：
While powered on, hold for 3s to turn off.
Manual pairing：
While powered off, hold for 5s to enter manual pairing state.
Recording：
While in the app’s recording interface, single click to
start/stop recording.
Calls：
Single click to take/hang up calls, hold for 1s to refuse
an incoming call
Music：
While playing music, double click to play/pause music. Omnidirectional
microphone
Power
button
USB-C
charging port
Indicator
light
3.5mm
audio jack

Bluetooth Connection
5
Connecting for the first time
Place your phone within 1m of SmartMike Classic.
Hold the power button for 3s. SmartMike Classic will turn on and enter Bluetooth pairing state.
The indicator light will flash rapidly in blue.
On your phone’s Bluetooth list, search for “SmartMike Classic” and click on it to connect via Bluetooth.
After connection is successful, SmartMike Classic’s indicator light will flash slowly in blue.
Automatic re-connecting
This applies to those who have already established a Bluetooth connection with SmartMike
Classic and their mobile phone.
With your phone’s Bluetooth turned on, turn on SmartMike Classic.
SmartMike Classic’s indicator light will change from rapid flash to slow flash in blue, indicating
that the reconnection is successful.
Manual pairing
This applies to those who have already established a Bluetooth connection with SmartMike
Classic and their mobile phone.
Hold the power button for 5s. SmartMike Classic will turn on and enter manual pairing state.
The indicator light will flash rapidly in blue.
On your phone’s Bluetooth list, search for “SmartMike Classic” and click on it to establish
Bluetooth connection.

Please use the USB-C charging cable to connect the device with a
USB charging port or a computer.
(1) Low battery warning：While battery is lower than 10%, indicator
light will flash slowly in red
(2) During charging：Indicator light will glow red
(3) Charge complete：Indicator light will glow green
Charging The Device
6

Precautions
7
1. Do not disassemble;
2. Do not expose the device to excessive heat, such as prolonged exposure to
the sun, near a fire source or similar environments;
3. The battery cannot be replaced by yourself. If you need to replace it, please
contact professional maintenance personnel;
4. Do not modify the device by yourself, do not use an external antenna alone or
use other transmitting antennas;
5. Please use a soft dry cloth to clean the equipment;
6. Do not expose device to water or other liquids;
7. Direct or indirect losses caused by violation of the rules of use are not
covered by warranty;
8. Do not swallow product or accessories;
9. If you have any questions or problems about this equipment that are not
covered in this manual, please contact us

FCC Warning Message
8
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.