SACAGAWEA DESIGNS VK-0002 Manual

© 2018
Order #XXXXX
Plan View
Perspective View
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
VK-0002 Table Top Display

© 2018
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2018
Case 1 of 1
Order #XXXXX
Top View of Each Level
Level 1 Level 2 Level 3
Graphic
Header
Graphic
Sign
Horizontal Extrusions 4A and 5A Horizontal Extrusions 4B and 5B
Vertical Extrusions 2 and 3
Wings
6A and 6B
Setup Hardware
Lights
7A 7B
Base
Plates
Graphics
Connection
Bars
Case Packing

© 2018
Step 1 of 2
Order #XXXXX
Item
1
2
3
4A,4B
5A,5B
6A,6B
7A,7B
Description
Base Plate
44” S40 Vertical Extrusion
44” S40 Vertical Extrusion
27.5” Z33 Horizontal Extrusion
27.5” Z33 Horizontal Extrusion
2.5” S40 Angle-Cut Vertical Extrusion
28.13” Z31 Curved Horizontal Extrusion
Qty.
2
1
1
1,1
1,1
1,1
1,1
Steps:
1) Attach base plates [1] TO vertical extrusions [2] and [3].
2) Connect horizontal extrusions [4A to 4B] and [5A to 5B], using connection bars.
See Straight Connection with Knobs detail.
3) Attach horizontal assemblies [4A/4B] and [5A/5B] between vertical extrusions [2] and [3].
4) Attach [6 to 2] and [6A to 3]. See 2.5” Angle-Cut Extrusion Attachment detail.
5) Connect
[7A] to [7B]. See General Information sheet for instruction.
6) Attach assembly [7A/7B] between verticals [6] and [6A].
7) Attach lights to assembled frame where desired. See Light Connection detail.
1
1
Completed Assembly
Connection
Bar w/ knobs
2
3
4A 4B
5A 5B
7A 7B
6
6A
**
Set Screw
Connector
Back View of Backwall
Insert connector into groove
of vertical extrusion, then
tighten set screw to secure.
Velcro
2.5” Angle-Cut
Extrusion Attachment
*
Light Connection
Connect light to
horizontal where
desired and
tighten in place.
*
Horizontal Placement
Stopper
Set upper horizontals
on top of stopper,
located on verticals.
Slide connection bar between
extrusions, then turn knobs
clockwise to tighten lock.
Straight Connection
with Knobs
Do not over tighten Knobs
Knob
Knob
**
VK-0002 Assembly

© 2018
Step 2 of 2
Order #XXXXX VK-0002 Attachments
2
3
7A
7B
Wing Wing
Graphic Header
Graphic
Sign
Steps:
1) Connect graphic header to Velcro on assembly [7A/7B].
2) Attach wings to A-10 clamps on verticals [2] and [3].
3) Attach graphic sign to vertical [3], using standoffs and screw caps.
See Graphic Sign detail.
Completed Assembly
*
Connector
Graphic Sign
Cap
Graphic
Standoff
Setscrew
Slide connector into groove of extrusion. Tighten
set screw to secure in place. Screw standoff into
connector. Place graphic between standoff and cap
then secure graphic to standoff, using cap.