Safco 1851 User manual

B
U
F
L
O
KR
N
M
C
E
A
T
V
W
O
K
S
W
P
Q
V
J
G
O
D
Z
H
Y
I
X
1851-37: 1 of 4; Rev. 3; 09/06
For questions or concerns, please call
Safco Consumer Hot Line 1-800-664-0042
available Monday-Friday 8:00 AM to 4:30 PM (Central Time)
(English-speaking operators)
Safco Products Company, New Hope, MN 55428
ASSEMBLED UNIT
MODEL 1851
Back Panel 1 1850-01§
Left Side Panel 1 1851-03§
Right Side Panel 1 1851-04§
Short Back Panel 1 1851-01§
Top Panel 1 1850-05§
Fixed Shelf 1 1851-06§
Tall Screw Post 16 HFFMFB
Tall Cam 16 HFFMFC
Short Screw Post 4 HMF12B
Short Cam 4 HMF12
Caster Bracket 4 1854-10
Machine Screw, 5/8”L 8 1850-22
Bottom Panel 1 1850-02§
Kick Panel 1 1850-07§
Wood Dowel 8 H8MMDWL
Swivel Caster with Brake 2 8917-24
Swivel Caster without Brake 2 8917-25
Hinge 4 8919-16
Hinge Mount Plate 4 8919-14
Left Door Panel 1 1850-08§
Right Door Panel 1 1850-09§
Handle 2 8962-31
Long Screw, 1”L 4 1850-23
Divider 1 1851-07§
Shelf Peg 24 HSFBNZ
Small Shelf 6 1851-08§
LETTER
CODE DESCRIPTION QTY. PART NO.
PARTS LIST
Sort and count your parts!
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
§Note: When corresponding about parts, be sure to state color:
Gray(GR),Mahogany(MH)orMediumOak(MO).
TOOLS REQUIRED: Short Handled Phillips Screwdriver; Hammer or Mallet (Two People Recommended)
PRODUCT WARRANTY REGISTRATION is available online at: www.safcoproducts.com
ASAS
ASAS
ASSEMBLSEMBL
SEMBLSEMBL
SEMBLYY
YY
Y INSTRUCTIONSINSTRUCTIONS
INSTRUCTIONSINSTRUCTIONS
INSTRUCTIONS
New Hope, MN 55428
Visit us on the web:
www.safcoproducts.com
an LDI Company
1851
Mobile Machine Stand

Insert two O Wood Dowels into both ends of
the N Kick Panel and the X Divider.
1851-37: 2 of 4; Rev. 3; 09/06 Safco Products Company, New Hope, MN 55428
IMPORTANT READ and FOLLOW these instructions carefully!
CHECK ALL PACKAGING - there may be parts in it!
SORT and COUNT your parts - compare with the parts list on page 1.
Work on a smooth and clean surface. Arrange the A Back
Panel, B Left Side Panel and C Right Side Panel with the
holes facing up as shown.
Place the D Short Back Panel
above the A Back Panel with large
holes up and insert J Short Cams
in the Short Back Panel. Arrange
the F Fixed Shelf below the Back
Panel and insert H Tall Cams in the
large corner holes of the Back
Panel and Fixed Shelf.
Insert two H Tall Cams in the two
large holes at the upper end of the
side panels, and insert two I Short
Screw Posts in the holes at the
upper center of each side panel.
Screw six G Tall Screw Posts into the small
holes in the upper, lower and back edges
of each side panel as shown. Fasten two K Caster
Brackets to the bottom end (unfinished edge) of each side
panel using two L 5/8” Machine Screws each.
Place the E Top Panel above the Short Back Panel with the
six small holes upward; screw four G Tall Screw Posts into the
corner holes.
1G
Raise the A Back Panel so it is perpendicular to the
B Left Side Panel. Align the two Screw Posts at the
back end of the Side Panel with the corresponding
holes on the Back Panel. With the arrows on the
Cams pointing toward the Screw Posts, guide the
holes over the Screw Posts and fasten by turning
each of the engaged cams CLOCKWISE as far as
they can turn. Install the D Short Back Panel in a
similar manner.
IMPORTANT: to prevent possible damage during
assembly, a second person should help support the
back panel in its upright position (or prop upright
with appropriate materials).
2
B
A
Position the F Fixed Shelf with the Cord Cutout next
to the A Back Panel, and the side with cams toward
the bottom end of the side panel. Align the two
Screw Posts on the Left Side Panel with the corre-
sponding holes on the edge of the Fixed Shelf. With
the arrows on the Cams pointing toward the Screw
Posts, insert the Screw Posts and fasten by turning
each of the engaged cams CLOCKWISE as far as
they can turn. Insert the screw posts on one end of
the M Bottom Panel into the holes on the bottom
end of the Left Side Panel and fasten the cams .
3
M
F
K
B
A
D
IC
L
BOTTOM
END
CORD
CUTOUT
D
LF
H
O
N
O
A
UNFINISHED
EDGES
E
K
I
X
J
FRONT;
FINISHEDEDGES
H
H

1851-37: 3 of 4; Rev. 3; 09/06 Safco Products Company, New Hope, MN 55428
FRONT
Q
Insert one dowel end of the N Kick Panel into the
Left Side Panel in the holes furthest from the Back
Panel.
4
Push the two P Swivel Casters with Brakes
into the sockets of the Caster Brackets at
the front of the unit. Push the two Q
Swivel Casters without Brakes into the
Caster Brackets near the back side of the
unit.
6
Lift the C Right Side Panel over the assembled
panels. Align the Screw Posts with the correspond-
ing holes on the Back Panel, Bottom Panel and
Fixed Shelf (also guide the Wood Dowels on the
Kick Panel into the holes in the side panel), then
fasten by turning each of the eight cams CLOCK-
WISE as far as they can turn.
5
U RIGHT DOOR PANEL
NOT SHOWN
LEFT
SIDE
PANEL
T
Use a soft hammer or mallet to tap the R Hinges into the
recesses on the T Left Door Panel. Use the pre-installed
screws to fasten the S Hinge Mount Plates into the pre-drilled
holes on the Left Side Panel. If the Hinge and Mount came in
separate pieces, bend the arms of the Hinges and insert the
slots of the arms over the Hinge Mount Plate set screws. Adjust
door position and tighten the set screws. Turn
the unit onto its right side, and repeat with the
U Right Door Panel.
7
R
ARM
SLOT
SET
SCREW
TIGHTEN
SET
SCREW
P
R
S
RS
N
C
FRONT

1851-37: 4 of 4; Rev. 3; 09/06 Safco Products Company, New Hope, MN 55428
With two people, carefully stand the unit upright.
Fasten one V Handle to the outer side of the Left
Door Panel using two W Long Screws. Fasten
the other Door Handle to the outer side of the
Right Door Panel with two more Long Screws.
If necessary, center the Door Panels by adjusting
the set screws on the Door Hinges as needed.
8
Lower the E Top Panel down onto the side panels
and divider. Guide the Dowels in the Divider into the
center holes in the Top Panel, and guide the Screw
Posts into the holes on the upper edges of the side
panels. Fasten by turning each of the four cams
CLOCKWISE until they stop.
10
V
W
E
Position the X Divider with the finished edge toward
the front of the unit, and insert the dowels into the
holes in the center of the F Fixed Shelf.
9
Insert Y Shelf Pegs into the small holes in both
compartments in the configuration you desire using
four pegs per shelf. Place Z Small Shelves onto the
Shelf Pegs.
Prevent the assembled unit from rolling by activating
the brakes on the Swivel Casters with Brakes.
11
Z
Y
V
X
F
BRAKES
FRONT;
FINISHED EDGE