Safeguard Supply LRA-DCRXA User manual

On
Off
Pad On
Pad 12V
Rea
dy
On
Off
Pad On
Pad 12V
Rea
dy
PARTS & FUNCTION
LRA-DCRXA Receiver
LRA-DCRXA Receiver
LRA-PBTXA Push Button
LRA-PBTXA Push Button
Battery compartment Battery cover
Speaker
Zone LED
Flasher
Zone selector
button
Melody
selector button
Volume control
Function Switch
Cancel
POWER
3 x 'C' size
'C
1.
' S
5
i
V
ze
'C
1.
' S
5
i
V
ze
' S
'C1.5iVze
Vibration Pad
On/Off
Vibration out
Indicator
DC Jack
Push button
Indicator
Mounting bracket
Battery compartment
Battery Cover
12V DC
400mA
Lock lever
Mounting holes
1
1
+
1. Use finger to unlock the lock lever
2. Rotate the mounting bracket 90 degrees and lift bracket from front of push button unit.
3. Remove the mounting bracket from the unit.
4. Rotate the Battery cover using a coin.
5. Insert a CR2032 battery to battery compartment provided.
6. Close the battery cover using a coin.
1. Flip to open the battery cover
2. insert 3 ‘C’ size batteries
3. Close the battery cove
LRA-DCRXA + LRA-PBTXA Wireless Chime Receiver with Strobe Manual
•Each LRA-DCRXA (receiver) can pair with a total of four (4) wireless transmitters
•Once four (4) transmitters have been paired to a receiver, you cannot add an additional
transmitter unless you delete a transmitter from the receiver
•There is no limit to the number of receivers you can pair with a transmitter
•The receiver is powered by 3 x c'-sized alkaline batteries or plug-in transformer (not included)
THINGS TO KNOW PRIOR TO USE
PRODUCT FEATURES & SPECIFICATIONS
•Wireless range from transmitter to receiver is up to 1,000 ft.(line of sight)
•Each receiver can pair with a total of two (2) transmitters
•Receiver has three (3) operating modes; a) sound only, b) strobe only & c) sound & strobe
•Assign one (1) of eighteen (18) available melodies to each transmitter
•Strobe has two flashing patterns; a) slow & b) fast
•Operating frequency: 868MHz
•Operating temperature: 32F to 104F
•Product dimensions: 2.5'' L x 1.2'' W x 4.72'' H
•Product weight: .45 lbs
•
Phone: [phone]
email: [email protected]
2260 Moon Station Ct. NW #110 Kennesaw GA 30144

+
When you have changed the code re-pair the telephone signaler.
Open the battery cover Press and hold the button, insert
the battery whilst holding the button for 5
seconds. The LED will flash 5 times when a new
code is generated
Take out the battery
1
+
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Note: Modifications to this product will void the user's authority to operate this equipment.
RoHS
2002/95/EC
CODE MATCHING & TUNE SELECTION
ID
Zone selector
button Melody selector
button
Function Switch
*Chime
*Light & Chime
*Light
Step1: Insert the battery into the transmitter to be used
(doorbell button)
Step 2: Insert the batteries into the receiver (chime unit).
Step 3: Enter pairing mode for the receiver (chime unit). Press &
hold
the ● zone selector button for 3 seconds. The LED in zone #1
will flash.
Step 4: Press the ● zone selector button again to move to the
zone you wish to pair with. Press the ♫ melody selector button
to scroll through the melodies. Once you hear a melody you
prefer, do not press any button as the melody is set for that
zone.
Step 5: Once the zone & melody are selected, trigger the
pusher once to pair. If successful, the receiver (chime unit) will
generate two short tones. Press the ● zone selector button to
exit the pairing mode, the system is now ready to use.
To stop the Chime while the receiver (chime unit) is alerting
press the reset button located on back, upper right-hand corner.
Delete the remote button on the chime memory
First, Press and hold the 'Learning' button for 3 seconds to enter the learning
mode. Press the 'Learn button to select the zone you want to delete. Press and
hold both the 'Learning' and the 'Melody' button 3 seconds. The chime will
generate a tone to indicate the remote on this zone has been deleted.
Change the melody/tone on desired zone
First, Press and hold the 'Learning' button for 3 seconds to enter the learning
mode. Press the 'Learn button to select the zone you want to change. Press the
'Melody' button to select the new melody/tone and then push the remote button.
You will hear a tone to indicate the melody has been changed.
BATTERY LOW INDICATOR
If a zone LED light is blinking, it indicates that the battery is low for this transmitter. You
must replace the battery as soon as possible. If the white flash at the top of the Chime
blinks every 5 seconds, this indicates the receiver batteries are low. You must replace the
batteries of the receiver.
Code Conflict If the bell press coding is the same as another transmitter you must change the code.
25mm
o
/ 7mm
Requires an electric drill for holes to fix the wall bracket
with the provided ram plug and screws.
49mm
4mm
+
+
Push Button Mounting with screws Push Button Mounting with double-sided adhesive
Stick the double-sided
adhesive on the
mounting bracket.
stick the bracket on
the door frame.
Put the bell press to the bracket
Put the push button into the bracket
at a 90 degree angle. Rotate the
push button clockwise until you fell it
locked
LRA-DCRXAReceiver
Wall mounded
Put on the desk Top
58mm
Installation
25mm
o
/ 7mm