Safety 1st 49270 User manual

49MHz Two-Way Intercom Monitor No. 49270
Owner’s Manual
Introduction
Thank you for purchasing the Safety 1st Two-Way Intercom Monitor.
We are confident that this advanced system will help keep you in tune with your baby’s
every sound, offering you two-way communication, clear reception, and portability.
Communication
• Two-way communication feature lets you soothe baby with your own voice or talk
to another adult
• Sound Lights let you see baby’s sound level
Reception
• 49 MHz technology provides superior clarity
• Extended range up to 400' (122 meters)
• Two channels to help minimize interference
Portability
• Both Units can run on battery power while you are on the go
• Parent’s Unit features a handy belt-clip for portability
• Units also run on household electricity – two A/C adapters included
Please read all instructions carefully before using the 49MHz Two-Way Intercom
Monitor. Keep these instructions for your future reference. If you have any
questions, please call our toll-free Consumer Relations number: [phone].
In Canada, please call [phone].
CAUTION:
• THE TWO-WAY INTERCOM NURSERY MONITOR IS NOT INTENDED
TO REPLACE RESPONSIBLE AND PROPER PARENTAL SUPERVISION.
• YOU SHOULD CHECK YOUR CHILD’S ACTIVITY AT REGULAR
INTERVALS AS THIS MONITOR WILL NOT ALERT PARENTS TO THE
SILENT ACTIVITIES OF A CHILD.
• KEEP ALL PARTS OF THIS MONITOR OUT OF REACH OF CHILDREN!
Page 1

Page 2
Safety Instructions
• TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT
EXPOSE THIS PRODUCT TO WATER OR MOISTURE. NEVER
TOUCH THE END OF THE ADAPTER CORD WHEN THE ADAPTER
IS PLUGGED INTO AN ELECTRICAL OUTLET.
• TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE
COVER OR BACK. NO SERVICEABLE PARTS INSIDE. REFER TO
SAFETY 1ST CONSUMER RELATIONS: [phone].
IN CANADA CALL [phone].
This device complies with part 15 of the FCC Rules. Operation is subject to
the following 2 conditions: (1) This device may not cause harmful interfer-
ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
The Baby’s Unit carrier frequency on channel A is 49.830 MHz and on
channel B is 49.845 MHz. The Parent’s Unit carrier frequency on channel A
is 49.875 MHz and on channel B is 49.890 MHz. The field strength is 80 dB
microvolts per meter at 3 meters.
WARNING: Changes or modifications to this unit not
expressly approved by Safety 1st, Inc. could void the
user’s authority to use the equipment.
WARNING

Page 3
Safety Instructions
Contents
HEED WARNINGS: All warnings on the Two-Way Intercom Monitor and operating instructions
should be adhered to.
WATER AND MOISTURE: The Two-Way Intercom Monitor should not be used near water, for
example, near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement, near a
swimming pool, etc.
VENTILATION: The Two-Way Intercom Monitor should be placed so that its location does not
interfere with proper ventilation of the unit. For example, it should never be situated on a bed,
sofa, rug or similar surface that may block ventilation.
HEAT: The Two-Way Intercom Monitor should be kept away from heat sources such as radiators,
heat registers, stoves or other appliances that produce heat.
AC POWER SOURCE: The Two-Way Intercom Monitor should be connected only to the AC Adapters
supplied with the Unit.
POWER CORD PROTECTION: The power supply cord should be routed so that it is not likely to be
walked on or pinched by items placed upon or against it. Pay particular attention to the cord at the
plug, convenience receptacle, and at the point it exits from the AC Adapters.
CLEANING: Use a dry cotton cloth to keep the Two-Way Intercom Monitor free from dust.
Do not use water!
NON-USE PERIODS: The power cords of the Two-Way Intercom Monitor should be unplugged
from the outlet when unused for long periods of time. The batteries should also be removed
during these periods.
OBJECT AND LIQUID ENTRY: Care should be taken so that objects do not fall onto the product,
and liquids are not spilled into the enclosure through the openings.
DAMAGE REQUIRING SERVICE: The Two-Way Intercom Monitor should be serviced by qualified
personnel when:
A: The power supply cord or plug has been damaged.
B: Objects have fallen or liquid has been spilled onto the product.
C: The Monitor has been exposed to rain.
D: The Monitor does not appear to operate normally or exhibits a marked change in its performance.
E: The Monitor has been dropped or the enclosure damaged.
2 AC Adapters
Parent’s Unit
(Requires one 9 volt alkaline
battery to operate in portable
mode. Not included.)
Baby’s Unit
(Requires one 9 volt alkaline
battery to operate in portable
mode. Not included.)

AC-9V IN
CHANNEL
AB
Page 4
AC Adapters
Features and Components - Baby’s Unit
Features and Components - Parent’s Unit
The AC Adapters are low voltage power sources that allow you to use your household
electricity to run the Parent’s and Baby’s Units. They connect to the AC Adapter jacks
in the Parent’s Unit and in the Baby’s Unit, and plug into any standard electrical outlet.
CAUTION: These Adapters were made with a specific design for this Safety 1st
Two-Way Intercom Monitor. They cannot be used with any other appliance. Never
use a different type of Adapter with this monitor.
1 On/Volume Dial
2 Power On (green)/Low Battery (amber)
LED Indicator
3 Two-Way Activation Button
4 Two-Way Mode LED (red) Indicator
5 Channel Selector
6 Antenna
7 Microphone
8 Speaker
9 AC Adapter Jack
10 Battery Compartment Door
1 On/Volume Dial
2 Power On (green)/Low Battery (amber) LED Indicator
3 Push to Talk Button
4 Channel Selector
5 LED Sound Lights (4)
6 Microphone
7 Antenna – turns 90° clockwise
to facilitate horizontal belt clip
8 AC Adapter Jack
9 Belt Clip
10 Battery Compartment
(1 screw in door)
4
5
2
3
6
13
10
AC-9V IN
CHANNEL
AB
CHANNEL
AB
7
2
8
9
5
WARNING: Never touch the end
of the adapter cord when the adapter is
plugged into an electrical outlet.
1 7
6
8
10
9
3 1
4

Page 5
Baby’s Unit:
For best results, place the Baby’s Unit on a table near the crib or bed. It should be
facing the baby’s head as close to the crib as possible, but out of baby’s reach.
To Use Baby’s Unit:
STEP 1 To use household power, plug the round end of adapter cord into the jack on the
Baby’s Unit, then plug the adapter into an electrical outlet.
NOTE: Battery power is available when one 9 volt alkaline battery (not included) is
installed in the Baby’s Unit. However, it is not recommended to use the battery power for
extended periods when household power is available.
STEP 3 Turn Unit on by using On/Volume Dial. Power On LED should illuminate solid green.
STEP 4 Set Baby’s Unit to channel“A”. If you hear interference, switch both Units to channel “B”.
NOTE: If you experience a power failure, the Baby’s Unit WILL NOT
automatically switch to battery power. You must disconnect the AC Adapter
from the Baby’s Unit and insure that (1) 9 volt alkaline battery (not included)
is installed for battery power.
To Install Battery (for use in Portable Mode):
(One 9 volt alkaline battery required, not included)
STEP 1 Locate battery compartment door on bottom of the Baby’s Unit as
shown in Figure A. Using Phillips head screwdriver, remove the screw to take
off the battery compartment door.
STEP 2 Snap 9 volt alkaline battery onto the battery clip, and return to battery
compartment as shown in Figure B. Replace battery compartment door and
secure with Phillips screwdriver, taking care not to over tighten.
NOTE: Power On/Low Battery LED Indicator illuminates (amber) when batteries
need replacing.
Parent’s Unit
To Use Parent’s Unit:
STEP 1 To use household power, plug the round end of adapter cord into the
AC Adapter Jack on the Parent’s Unit, then plug the adapter into an electrical
outlet. Turn the On/Volume Dial to “ON” and set at an appropriate volume level
to hear baby at all times. The Power On LED Indicator on the Parent’s Unit
should be illuminated solid green.
NOTE: If you experience a power failure, the Parent’s Unit WILL NOT
automatically switch to battery power. You must disconnect the AC
Adapter from the Parent’s Unit and ensure that one 9 volt alkaline
battery (not included) is installed for battery power.
NOTE:If you experience static or noise interference, you may need to change
channels on both Units.
STEP 2 To clip over waist band or belt, as shown in Figure E, rotate antenna 90°.
To Install Battery (for use in Portable Mode):
(One 9 volt alkaline battery required, not included)
STEP 1 Locate battery compartment door on back of the Parent’s Unit as
shown in Figure C. Using Phillips head screwdriver, remove the screw to take off
the battery compartment door.
STEP 2 Snap 9 volt alkaline battery onto the battery clip, and return to battery
compartment as shown in Figure D. Replace battery compartment door and
secure with Phillips screwdriver, taking care not to over tighten.
NOTE:Power On/Low Battery LED Indicator illuminates (amber) when batteries need replacing.
NOTE:If you experience static or noise interference, you may need to change channels
on both Units.
Operating your 49MHz Two-Way Intercom Monitor
Follow these instructions to operate your 49 MHz Two-Way Intercom Monitor. Reference the
illustrations on page 4 for the location of all features described in these instructions.
AC-9VIN
AC-9VIN
AC-9VIN
AC-9VIN
A
B
C
D
E