Safety Vision LED7B-TQ User manual

USER GUIDE
LED7B-TQ
LED10B-TQ

LED7B-TQ / LED10B-TQ USER GUIDE
Document Version: 1
Revision: 0
Safety Vision attempts to provide information contained in this
manual based on the latest product information available at the time
of publication. However, because of Safety Vision’s policy of continual
product improvement, Safety Vision reserves the right to amend the
information in this document at any time without prior notice.
This material is confidential and the property of Safety Vision. It is shared
with your company for the sole purpose of helping you with the operation
of the described equipment.
Safety Vision makes no warranty of any kind with regard to this material,
including, but not limited to, the implied warranties of merchantability
and fitness for a particular purpose. Safety Vision shall not be liable for
errors contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this material.
Safety Vision expressly disclaims all responsibility and liability for the
installation, use, performance, maintenance, and support of third-party
products. Customers are advised to make their independent evaluation of
such products.
No part of this document may be photocopied, reproduced, or translated
to another language without the prior written consent of Safety Vision.
Safety Vision®is a registered trademark of Safety Vision, LLC. All other
products or name brands mentioned in this document are trademarks of
their respective owners. For more information about Safety Vision and its
products, go to www.safetyvision.com or call 800-880-8855.
LED7B-TQ / LED10B-TQ USER GUIDE

TABLE OF CONTENTS
WHAT’S IN THE BOX? 1
Monitor 2
IR Remote Control 3
INSTALLATION
Before You Start 4
Fan-Shaped Bracket 5
U-Shaped Bracket 7
WIRING 8
Troubleshooting 10
OPERATION
Powering On the Monitor 11
Opening / Closing the Main Menu 11
Enabling/Disabling the Touchscreen 11
Switching between Camera Feeds 12
Viewing a Single Camera Feed 13
Swapping Camera Feeds 14
Zooming In/Out of Camera Feeds 14
Selecting a Single Camera Audio Feed 14
NAVIGATING THE MAIN MENU
Volume 15
Dimmer 16
Camera Feed Sizes and Positions 17
Audio Output Feed(s) 20
LED7B-TQ / LED10B-TQ USER GUIDE

Input 22
Settings 23
Camera 24
Parking Line 25
Language 28
Trigger 29
Auto Scan 30
Power On 31
Standard 32
System 33
Entering / Exiting Standby Mode 35
MAINTENANCE
Operation 36
Cleaning 36
Disclaimer 36
APPENDIX A SPECIFICATIONS 37
CLIENT SUPPORT 38
TECH SUPPORT 38
FCC COMPLIANCE STATEMENT 38
LED7B-TQ / LED10B-TQ USER GUIDE

LED7B-TQ / LED10B-TQ USER GUIDE
1
WHAT’S IN THE BOX?
• Monitor
• Wiring harness
• Fan-shaped mounting bracket
• U-shaped mounting bracket
• Mounting bracket angle adjustment screws
• HDMI adapter
• Sun shield
• Infrared (IR) remote control (CR2025 battery not included)

LED7B-TQ / LED10B-TQ USER GUIDE
2
Monitor
1 HD touchscreen
2 Infrared sensor
3 Power button
4 Light level sensor
5 Speaker
6 HDMI adapter
7 AV input

LED7B-TQ / LED10B-TQ USER GUIDE
3
IR Remote Control
DOWN
Moves cursor down
MUTE
Mutes and unmutes speaker
LANG
Enters the Language menu
AV
This button is not used
MENU
Enters the Main Menu or
returns to the previous menu
MODE
Switches the monitor input
between DVI (HDMI) and
cameras (CAM)
P/N
This button is not used
POWER
Power on or put monitor in
standby mode
REST
Restores factory defaults
SELECT
Enters a selection
UP
Moves cursor up
LEFT
Decreases volume / moves
cursor left
RIGHT
Increases volume / moves
cursor right

LED7B-TQ / LED10B-TQ USER GUIDE
4
INSTALLATION
Before You Stat
• To reduce the risk of electric shock, disconnect the vehicle battery
before installing the monitor.
• Do not install the monitor where it may interfere with safe vehicle
operation or prevent air bag deployment.
• To allow adequate air circulation around the device, leave at least two
inches of space between the monitor and walls, cabinets, or other
objects.
• Route cables where they may not be pinched, stepped on, or interfere
with passenger mobility.
• Do not bend, force, or ovetighten connections.
• Before connecting the monitor, confirm the output voltage of the
power supply is between 10 and 32V DC.
• When connecting the monitor to a power supply, observe polarity to
prevent damage.

LED7B-TQ / LED10B-TQ USER GUIDE
5
Fan-Shaped Bracket
Select a safe position within the observer’s line of sight (for example, on the
dashboard) to install the monitor.
1. Secure the monitor bracket to the mounting surface with the supplied
screws, the pre-applied high-bond adhesive, or both.

LED7B-TQ / LED10B-TQ USER GUIDE
6
2. Slide the monitor onto the mounting bracket to the desired height and
tighten the locknut to secure the monitor to the mounting bracket.
3. Adjust the monitor horizontally and vetically, then tighten the handle
screw to lock the monitor into position.
(Fan-Shaped Bracket cont.)

LED7B-TQ / LED10B-TQ USER GUIDE
7
U-Shaped Bracket
Select a safe position within the observer’s line of sight (for example, on the
dashboard) to install the monitor.
1. Secure the monitor U-shaped bracket to the mounting surface with the
supplied screws.
2. Slide the monitor into the U-shaped bracket and thread the 4 angle
adjustment screws through the bracket and into the mounting holes on
either side of the monitor.
3. Adjust the monitor to the desired angle and secure it in place by
tightening each of the 4 angle adjustment screws.

WIRING
LED7B-TQ / LED10B-TQ USER GUIDE
8
1. Connect the 22-pin DIN connector on the wiring harness to the 22-pin
DIN connector on the monitor cable.
2. Connect camera 1 to the Cam1 input on the wiring harness.
3. Repeat the previous step for cameras 2 through 4 as needed.

LED7B-TQ / LED10B-TQ USER GUIDE
9
WIRE DESCRIPTION
VCC Ignition power 10-32V DC
GND Ground
TRI1
Reverse (typically connected to vehicle’s backup lights).
• When activated, the monitor receives input from
camera 1.
TRI2 When activated, the monitor receives input from camera 2.
TRI3 When activated, the monitor receives input from camera 3.
TRI4 When activated, the monitor receives input from camera 4.
TRI5 When the trigger is activated, the monitor displays a Double
Split screen by default; however, this may be customized.
4. Connect the individual wires on the wiring harness as follows:
(Wiring cont.)

LED7B-TQ / LED10B-TQ USER GUIDE
10
Troubleshooting
If a camera does not display when connected to the monitor, users may
troubleshoot by forcing an automatic detection. To force automatic
detection,
1. Open the Main Menu and tap Settings .
2. Tap Standard. The following menu will appear:
3. With Automatic set to Off, tap the . The following window and
progress bar will appear:
NOTE: When the status bar reaches 100%, resolution and video format type will
appear for each camera. Missing information indicates an unrecognized camera.
4. To exit, tap outside the result window.

LED7B-TQ / LED10B-TQ USER GUIDE
11
OPERATION
Powering On the Monitor
Upon turning the vehicle ignition, the monitor will automatically power on. The
H-shaped split screen layout will display by default.
Opening / Closing the Main Menu
• To open the Main Menu, tap the screen anywhere in the bottom fouth
of the screen, as demonstrated in the red box below.
• To exit the Main Menu, tap the screen anywhere above the area in red
box shown below.
Enabling/Disabling the Touchscreen
Within the LED7-TQ and LED10-TQ interfaces, Menu Lock is the term used to
describe whether the touchscreen is usable or not.
• To enable Menu Lock,
1. Ensure the Main Menu is not displayed.
2. Press the physical power button for 3 seconds.
• To disable Menu Lock, press the physical power button for 3 seconds.

LED7B-TQ / LED10B-TQ USER GUIDE
12
Viewing Camera Feeds
Switching between Camera Feeds
To switch between camera feeds and split screen layouts, swipe a finger left
or right across the screen.
1. Camera 1
2. Camera 2
3. Camera 3
4. Camera 4
5. Double Split
6. Triple Split
7. Y-shaped Split 1
8. Y-shaped Split 2
9. H-shaped Split
10. Quad Split
11. PIP Split 1
12. PIP Split 2
13. PIP Split 3
14. Special Picture Split
Cameras display in the following order:
NOTE: Users may only swipe between cameras when the monitor source is set to
Cameras (see the Inputs section).

LED7B-TQ / LED10B-TQ USER GUIDE
13
Viewing a Single Camera Feed
• To view a single camera feed within a split screen layout, tap the
desired camera feed.
• To exit a single camera feed and return to a split screen layout, tap the
camera feed again.

LED7B-TQ / LED10B-TQ USER GUIDE
14
Swapping Camera Feeds
Using two fingers, tap two different camera feeds simultaneously. The two
camera feeds will swap positions.
Zooming In/Out of Camera Feeds
NOTE: Split screen layouts do not support zoom.
• To zoom in on a camera feed,
1. Tap the desired camera feed.
2. Define the zoom area by placing two fingers on the screen and
spreading them apat. A red border will appear.
3. To activate the zoom, tap within the red border.
• To exit the zoom view, tap within the red border or press the physical
power button.
Selecting a Single Camera Audio Feed
Using two fingers, tap within the desired camera feed. An audio icon will
appear at the bottom right of the camera feed. This will designate this camera
feed as the new audio output.

LED7B-TQ / LED10B-TQ USER GUIDE
15
NAVIGATING THE MAIN MENU
Tap an icon (Volume, Dimmer, Display,Input, Settings, or Power)to enter
corresponding submenus.
Volume
Tap the Volume icon to adjust audio levels. The following window will appear:
• To adjust the volume, drag the volume slider bar to the left (decrease)
or right (increase).
• To mute, tap the speaker icon. Tap the icon again to unmute.
To exit, tap away from the volume slider bar.

LED7B-TQ / LED10B-TQ USER GUIDE
16
Dimmer
Tap the Dimmer icon to change camera views. The Dimmer menu will appear
when Auto Dimmer is off (default).
NOTE: See Screen Brightness to toggle Auto Dimmer on.
To change brightness when Auto Dimmer is off, adjust the single slider bar.
To change brightness when Auto Dimmer is on (see Screen Brightness), adjust
the dual slider bars.
• To set the maximum brightness, adjust the slider bar.
• To set minimum brightness, adjust the slider bar.
To exit, tap away from the slider bar(s).