Safety Vision 56BA-AHD User manual

USER GUIDE
56BA-AHD
70BA-AHD

56BA-AHD/70BA-AHD USER GUIDE
Document Version: 1
Revision: 0
Safety Vision attempts to provide information contained in this
manual based on the latest product information available at the time
of publication. However, because of Safety Vision’s policy of continual
product improvement, Safety Vision reserves the right to amend the
information in this document at any time without prior notice.
This material is confidential and the property of Safety Vision. It is shared
with your company for the sole purpose of helping you with the operation
of the described equipment.
Safety Vision makes no warranty of any kind with regard to this material,
including, but not limited to, the implied warranties of merchantability
and fitness for a particular purpose. Safety Vision shall not be liable for
errors contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this material.
Safety Vision expressly disclaims all responsibility and liability for the
installation, use, performance, maintenance, and support of third-party
products. Customers are advised to make their independent evaluation of
such products.
No part of this document may be photocopied, reproduced, or translated
to another language without the prior written consent of Safety Vision.
Safety Vision®is a registered trademark of Safety Vision, LLC. All other
products or name brands mentioned in this document are trademarks of
their respective owners. For more information about Safety Vision and its
products, go to www.safetyvision.com or call 800-880-8855.
56BA-AHD/70BA-AHD USER GUIDE

TABLE OF CONTENTS
OVERVIEW 1
BEFORE YOU START 1
SUPPLIED HARDWARE 1
HARDWARE COMPONENTS 2
INSTALLATION 3
WIRING 4
INITIAL SETUP
Camera 2 Input 5
SYSTEM OPERATION
System Power 5
APPENDIX A SPECIFICATIONS 6
CLIENT SUPPORT 7
TECH SUPPORT 7
FCC COMPLIANCE STATEMENT 7
56BA-AHD/70BA-AHD USER GUIDE

56BA-AHD/70BA-AHD USER GUIDE
1
OVERVIEW
Suppoting up to two cameras, the Safety Vision 56BA-AHD (5.6-inch screen)
and 70BA-AHD (7-inch screen) 1080p monitors provide views of a single blind
spot or multiple for full coverage. The compact flat screen monitors take
minimal space while providing you with a clear view of your most vulnerable
areas. Neither monitor require a separate control box, allowing for a much
cleaner and easier installation.
BEFORE YOU START
These instructions are intended to ensure that users can use the product
correctly and avoid danger or propety damage.
• Before inseting fasteners into the mounting surface, ensure that the
underside of the mounting surface is clear of equipment that might
be damaged by the screws.
• Use only the correct voltage (12 VDC).
• To reduce the risk of electrical shock, disconnect vehicle battery
before stating the installation.
• To avoid the risk of electric shock, do not disassemble the system
components, and keep cables away from sharp objects.
• Select inconspicuous cable routes that do not interfere with normal
driver or passenger mobility.
• Clean only with a dry cloth.
• Do not allow the power cable to become pinched or damaged.

56BA-AHD/70BA-AHD USER GUIDE
2
SUPPLIED HARDWARE
The following hardware is supplied in the box for installation with each
56BA-AHD/70BA-AHD system:
• SV-LCDBBRKY (monitor mount)
• Five (5) M3 x 12 Phillips drive, washer head self drilling screws
• One (1) roll of black tape
56BA-AHD/70BA-AHD monitors purchased as pat of a SV-LCD56BA-AHDP
or SV-LCD70BA-AHDP kit, will also seperately include:
• One (1) SV-LCDBA3.7M power cable

56BA-AHD/70BA-AHD USER GUIDE
3
1 POWER LED — Indicates that
the monitor has power.
2 DAY/NIGHT SENSOR —
Senses available light and
adjusts monitor brightness
accordingly.
3 MENU BUTTON — Initiates
display of on-screen user
controls for image contrast
and brightness and speaker
volume.
4 + BUTTON (Up button) —
Increases the value for Setup
menu items (e.g. volume).
5 – BUTTON (Down button) —
Decreases the value for Setup
menu items (e.g. volume).
6 POWER/CAM SELECT BUTTON
—Press and hold for 1 second
to turn the monitor on or off;
press briefly to switch image
input.
7 NORMAL/MIRROR SWITCH
—Switches image display to
Normal or Reverse (as it would
appear in a rear-view mirror)
8 BRACKET SLOT — Accepts the
adjustable mounting bracket
9 MONITOR CABLE — Receives
power and camera images
from the camera.
HARDWARE COMPONENTS

56BA-AHD/70BA-AHD USER GUIDE
4
INSTALLATION
1. Select a mounting surface for the monitor, which can be mounted
overhead or elsewhere in the vehicle cabin (including on the floor or
console). The mounting surface should:
• Be level, waterproof, ventilated adequately, and capable of
suppoting the weight of the monitor and mounting bracket
• Not be close to a vehicle speaker (to prevent interference from the
speaker’s magnetic field)
• Not be extremely hot or humid
2. Secure the monitor bracket to the mounting surface with the supplied
screws, the pre-applied high-bond adhesive, or both.

56BA-AHD/70BA-AHD USER GUIDE
5
3. Slide the monitor onto the mounting bracket to the desired height and
tighten the locknut to secure the monitor to the mounting bracket.
4. Adjust the monitor horizontally and vetically, then tighten the handle
screw to lock the monitor into position.
(Installation cont.)

56BA-AHD/70BA-AHD USER GUIDE
6
WIRING
1 Connect the 13-pin DIN connector on the wiring harness to the 13-pin
DIN connector on the monitor cable.
2 Connect the camera extension cable to the connector labeled as
“Camera 1” on the wiring harness.
3 Connect the individual wires on the wiring harness as follows:
WIRE COLOR DESCRIPTION
Red Ignition
Black Chassis ground
Green (Trigger 1)
Reverse (typically the wire for the backup lights).
• When this wire has 12 VDC, the monitor receives
input from camera 1.
White (Trigger 2)
(Optional)
Vehicle wire that has 12 VDC when a separate event
(such as activating a turn signal) occurs.
• When this wire has 12 VDC, the monitor receives
input from an optional camera 2.
Note
Camera 1 input takes priority over Camera 2 input.
Yellow (Audio) Camera 1 audio

56BA-AHD/70BA-AHD USER GUIDE
7
INITIAL SETUP
1 To initiate display of the main menu, press the MENU button on the front
panel of the monitor. Use the UP and DOWN buttons to increase and
decrease values for menu items.
NOTE: After several seconds of inactivity, the menu is no longer displayed, and
the MENU button must be pressed again to initiate display of the main menu
again.
2 Menu items can be changed as follows:
MENU ITEM FUNCTION
CONTRAST Adjusts the contrast level between dark and light images
BRIGHT Adjusts the brightness intensity level
VOLUME Adjusts the volume of the integrated speaker
Camera 2 Input
By default the 56BA-AHD/70BA-AHD monitors are set to receive one
camera (Camera 1) input only.
To configure the monitor to receive two inputs, ensure a second camera
(Camera 2) is connected, and use the following procedure:
1. Press the -(down) button, then the +(up) button.
2. Repeat step 1 five times (ten total button presses).
3. Press the Menu button.
4. When TO B2 RESET appears on the screen, press the Power button

56BA-AHD/70BA-AHD USER GUIDE
8
The monitor is sensitive to the timing that the -and +buttons are pressed. If
at first TO B2 RESET does not appear on the screen, try again, pressing the
buttons more slowly (or more quickly) and consistently.
When the monitor is powered up again, press the Power button to switch
between cameras 1 and 2.
SYSTEM OPERATION
System Power
In typical installations, the system is placed into standby mode automatically
when the sensor wire for the vehicle ignition is activated, and the monitor
automatically displays camera input when the sensor wire for the vehicle
backup lights is activated. The system can also be powered on and off
manually with the Power button on the front panel of the monitor.

APPENDIX A SPECIFICATIONS
56BA-AHD/70BA-AHD USER GUIDE
9
SCREEN SIZE
56BA-AHD: 5.6”
70BA-AHD: 7"
ASPECT RATIO
56BA-AHD: 4:3
70BA-AHD: 16:9
RESOLUTION
1080p
VIEWING ANGLES U/D/L/R
56BA-AHD: 45°/65°/65°/65°
70BA-AHD: 40°/60°/60°/60°
BRIGHTNESS
56BA-AHD: 200 cd/m2
70BA-AHD: 500 cd/m2
RESPONSE TIME
20 ms (at 77° F [25° C])
CONTRAST RATIO
56BA-AHD: 500:1
70BA-AHD: 800:1
VIDEO INPUT
2 channels
VIDEO MODE
AHD/CVBS (auto)
ONSCREEN DISPLAY CONTROLS
Color, Brightness, Contrast,
Volume, Languages
POWER REQUIREMENT
12/24V DC
POWER CONSUMPTION
≤ 10W
OPERATING TEMPERATURE
-4° F ~ 158° F (-20° C ~ 70° C)
STORAGE TEMPERATURE
-22° F ~ 176° F (-30° C ~ 80° C)
DIMENSIONS W × H × D
56BA-AHD:
6.5 × 4.53 × 1.14 in
(165 × 115 × 29 mm)
70BA-AHD:
7.68 × 4.65 × 2.32 in
(195 × 118 × 59 mm)

CLIENT SUPPORT
The Client Support team serves as the voice of Safety Vision; ensuring an optimal experience
through the entire client relationship. They interact with every department in the company to
accommodate your needs and deliver on every inquiry or request. Whether you want to place an
order, would like more information on a product, or anything in between; our team is here for you.
Hours: 7AM-6PM CST
Phone Number: 713-929-1111
TECH SUPPORT
Our Tech Support team provides training, problem solving, and instruction on all of our solutions
and is available to speak with you on the phone. The team guarantees to respond within one
business day and ensures you are fully equipped to understand and utilize our products to their
maximum capabilities. They’re dedicated to educating you on our solutions step-by-step and are
always available to trouble-shoot any of our solutions.
Hours: 7AM-6PM CST
Phone Number: 713-929-1164
FCC COMPLIANCE STATEMENT
This device has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference in which case the user
will be required to correct the interference at is own expense.
Any changes or modifications in construction of this device which are not expressly approved by
the party responsible for the compliance could void the user’s authority to operate the equipment.
56BA-AHD/70BA-AHD USER GUIDE
10

Copyright © 2022 Safety Vision, LLC All Rights Reserved.
6100 W. SAM HOUSTON PKWY. N.
HOUSTON, TX 77041-5113
MAIN: 713.896.6600
TOLL FREE: 800.880.8855
SAFETYVISION.COM