SafeWaze 019-11003 User manual

WARNING
This product is part of a personal fall arrest, work positioning, or rescue system. The manufacturer’s instructions must be provided to
users of this equipment. The user must follow the manufacturer’s instructions for each component of the system. The user must read and
understand these instructions before using this equipment. Manufacturer’s instructions must be followed for proper use and maintenance
of this equipment. Alterations to this product, misuse of this product, or failure to follow instructions may result in serious injury or death.
IMPORTANT
Questions regarding the use, care, or suitability of this equipment for your application? Contact SafeWaze.
IMPORTANT
Record initial usage of product on Page 2, and Page 15. Competent Person inspections are required to be documented in the Inspection
Log Table on Page 15.
019-11003
Tripod with 65’ Material Winch
and 65’ 3-Way
2057
User Manual
V1.0 2020 Copyright SafeWaze Page 1

TABLE OF CONTENTS
1 INTRODUCTION....................................................................................3
2 APPLICABLE SAFETY STANDARDS....................................................3
3 WORKER CLASSIFICATIONS...............................................................3
4 PRODUCT SPECIFIC APPLICATIONS..................................................4
5 LIMITATIONS..........................................................................................4
6 COMPATIBILITY OF CONNECTIONS ...................................................5
7 MAKING CONNECTIONS......................................................................6
8 COMPONENTS AND SPECIFICATIONS...............................................7
9 INSTALLATION AND USE....................................................................8-12
10 OPERATION........................................................................................12-13
11 INSPECTION.......................................................................................13-15
12 INSPECTION LOG................................................................................15
13 SAFETY INFORMATION.....................................................................16-17
14 LABELS.................................................................................................17
Do not throw away these instructions!
Read and understand these instructions before using equipment!
User Information
Date of First Use:
Serial#:
Trainer:
User:
User Manual
V1.0 2020 Copyright SafeWaze Page 2

INTRODUCTION
Thank you for purchasing the SafeWaze 019-11003 Conned Space System. This manual must be
read and understood in its entirety, and used as part of an employee training program as required by
OSHA or any applicable state agency.
This manual and any other instructional material must be available to the user of the equipment.
The user must understand how to safely and e󰀨ectively use the 019-11003, and all fall protection
equipment used in conjuction with the 019-11003.
The 019-11003 Conned Space System is designed primarily for workers entering and working in
conned space environments. OSHA denes conned space as any space with limited openings for
entry and exit, is large enough for a worker to enter bodily and perform work, and is not designed for
continuous worker occupancy.
Conned spaces include but are not limited to, utility manholes, silos, undergound utility vaults,
storage containers, pits, and pipelines.
The 019-11003 Conned Space Tripod serves as the support element for entry/egress into conned
spaces, and also the rescue/evacuation of workers if necessary. It can also provide anchorage for fall
protection, work postioning, and personnel riding systems.
APPLICABLE SAFETY STANDARDS
When used according to instructions, this product meets or exceeds all applicable OSHA 1926.502
OSHA 1910.146, OSHA 1926.21, ANSI Z359.1-2007, ANSI Z117.1-2009, ANSI Z359.14-2014,
ANSI A10.32-2012 standards for fall protection. Applicable standards and regulations depend on the
type of work being done, and also might include state-specic regulations. Refer to local, state, and
federal (OSHA) requirements for additional information concerning the governing of occupational
safety regarding Personal Fall Arrest Systems (PFAS).
Worker Classifications
Understand the denitions of those who work in proximity of or may be
exposed to fall hazards.
Qualied Person: A person with an accredidated degree or certication, and with extensive
experience or su󰀩cient professional standing, who is considered procient in planning and reviewing
the conformity of fall protection and rescue systems.
Competent Person: A highly trained and experienced person who is assigned by the employer to
be responsible for all elements of a fall safety program, including, but not limited to, its regulation,
management, and application. A person who is procient in identifying existing and predictable
hazards, and who has the authority to stop work in order to eliminate hazards.
Authorized Person: A person who is assigned by their employer to work around or be subject to
potential or existing fall hazards.
It is the responsibility of a Qualied or Competent person to supervise the job site and
ensure safety regulations are complied with.
User Manual
V1.0 2020 Copyright SafeWaze Page 3

Product Specific Applications
Rescue / Conned Space: The 019-11003 Conned Space System may be used in both Conned
Space and Rescue applications. Rescue systems function to safely remove a worker from a conned
space environment or after exposed to a fall. There are various congurations of rescue systems
depending on the type of rescue required. Structure must withstand loads applied in the directions
permitted by the system of at least 3,000 lbs. No free fall is permitted. Applicable D-rings are dorsal,
chest, and shoulder.
Lanyard Length
(6’ Total)
Deceleration
distance (4’ total)
Height of harness
dorsal D-ring from
worker’s feet
(6’ total)
Safety factor
(2’ total)
Required
distance
from
Anchorage
(18’ total)
Fall Clearance: There must be su󰀩cient clearance below the anchorage connector to arrest a fall
before the user strikes the ground or an obstruction. When calculating fall clearance, account for a
MINIMUM 2’ safety factor, deceleration distance, user height, length of lanyard/SRL, and all other
applicable factors. (See Figure 1)
Limitations
Fall Clearance Diagram
***Diagram shown is an example
fall clearance calculation ONLY. For all applications: worker weight capacity range
(including all clothing, tools, and equipment) is 130-310 lbs
FIGURE 1
User Manual
V1.0 2020 Copyright SafeWaze Page 4

Swing Falls: Prior to installation or use, make considerations for eliminating or minimizing all swing
fall hazards. Swing falls occur when the anchor is not directly above the location where a fall occurs.
Always work as close to in line with the anchor point as possible. Swing falls signicantly increase
the likelihood of serious injury or death in the event of a fall. (See Figure 2)
A
FALL-ARREST
S
W
I
N
G
F
A
L
L
COMPATIBILITY OF CONNECTORS
Connectors are compatible with connecting elements when they have been designed to work together
in such a way that their sizes and shapes do not cause their gate mechanisms to inadvertently
open regardless of how they become oriented. Connectors (hooks, carabiners, and D-rings) must
be capable of supporting at least 5,000 lbs. (22.2 kN). Connectors must be compatible with the
anchorage or other system components (see Figure 4). Do not use equipment that is not compatible.
Non- compatible connectors may unintentionally disengage (see Figure 3). Connectors must be
compatible in size, shape, and strength. Self-locking snap hooks and carabiners are required by
ANSI Z359 and OSHA guidelines. Contact SafeWaze if you have any questions about compatibility.
FIGURE 3 - UNINTENTIONAL DISENGAGEMENT
Non-compliant part
Using a connector that is undersized or irregular in shape (1) to connect a snap hook or carabiner
could allow the connector to force open the gate of the snap hook or carabiner. When force is applied,
the gate of the hook or carabiner presses against the non-compliant part (2) and forces open the gate
(3). This allows the snap hook or carabiner to disengage (4) from the connection point.
3 - gate opens
2 - gate presses
against
non-complaint
part
4 - and parts disengage.
1 -
NOTE: SOME SPECIALITY CONNECTORS HAVE ADDITIONAL REQUIREMENTS.
CONTACT SAFEWAZE WITH QUESTIONS.
FIGURE 2
User Manual
V1.0 2020 Copyright SafeWaze Page 5

User Manual
V1.0 2020 Copyright SafeWaze Page 6
MAKING CONNECTIONS
Snap hooks and carabiners used with this equipment must be double locking and/or twist lock.
Ensure all connections are compatible in size, shape and strength. Do not use equipment that is not
compatible. Ensure all connectors are fully closed and locked.
SafeWaze connectors (snap hooks and carabiners) are designed to be used only as specied in each
product’s user’s instructions. See gure 4 for examples of inappropriate connections. Do not connect
snap hooks and carabiners:
• To a D-ring to which another connector is attached.
• In a manner that would result in a load on the gate (with the exception of tie back hooks).
• NOTE: Large snap hooks must not be connected to objects which will result in a load on the
gate if the hook twists or rotates, unless the snap hook complies with ANSI Z359.1-2007 or ANSI
Z359.12 and is equipped with a 3,600 lb (16 kN) gate. Check the marking on your snap hook to
verify its compatibility.
FIGURE 4 - INAPPROPRIATE CONNECTIONS
• In a false engagement, where features that protrude from the snap hook or carabiner catch on the
anchor, and without visual conrmation seems to be fully engaged to the anchor point.
• To each other.
• By wrapping the web lifeline around an anchor and securing to lifeline except as allowed for Tie
Back models.
• To any object which is shaped or sized in a way that the snap hook or carabiner will not close and
lock, or that roll-out could occur.
• In a manner that does not allow the connector to align properly while under load.

Components and Specifications
Tripod Safety Chain
Pulleys
019-11003
Tripod with 65’ Material Winch
and 65’ 3-Way
Adjustable Legs
3-Way
Material Winch
Tripod
Interior Headroom 81 in (2057.4 mm)
Distance Between Feet 61 in (1549.4 mm)
Max Diameter Hole 44 in (1117.6 mm)
Working Load 350 lbs (158.76 kg)
Overall Height 84 in (2133.6 mm)
Storage Length 65 in (1651 mm)
Outside Head Diameter 17 in (431.8 mm)
Leg Adjustment Increments 6 in (152.4 mm)
Weight 50 lbs (22.68 kg)
Length/Type 65 ft (19.81 m) Galvanized Steel
Breaking Strength 4200 lbs (1905.08 kg)
Maximum Work Load 310 lbs (140.61 kg)
Minimum Work Load 110 lbs (49.9 kg)
Locking Speed 4 - 5 ft/sec (1.22 - 1.52 m/sec)
Stopping Distance < 54 in (1371.6 mm)
Speed Rescue Mode Approximate 20 ft/min (6.1 m/min)
Gear Ratio 5.5:1
Mechanical Advantage 29 lbs (13.15 kg)
Weight 35 lbs (15.88 kg)
3-Way
Cable 0.19 in (4.83 mm) steel
Weight 32 lbs (14.52 kg)
Lifting Capacity 600 lbs (272.16 kg)
Size 11 in x 8 in (279.4 mm x 203.2 mm)
Handle Length 14 in (355.6 mm)
User Manual
V1.0 2020 Copyright SafeWaze Page 7

Installation and Use
Step 1: Remove tripod from tripod storage/carrying bag.
Step 2: Tripod must be mounted on a stable level surface for each leg, when positioned over
opening, with a Maximum Installation Diameter of 44 inches. Lift tripod to upright position. Press
locking pin above each leg in the tripod head and pull leg away from center point until locking pin
locks into place. Repeat with the remaining legs. (See Image 1)
Step 3: Remove Locking Pins above foot of tripod legs and extend legs to desired height. Re-insert
locking pin at desired height, (See Image 2) and connect safety chains to bottom of tripod legs.
Remove excess slack in the safety chain by adjusting the position of the twist link.
Step 4: This step decribes actions to be taken if attaching / installing a Safewaze 3-Way Retractable,
Material Winch, or Personnel Winch onto the tripod via mounting to one of the tripod legs. This step
must be performed in order to ensure proper routing of component cables through the top of the
tripod. Remove Cotter Pins, Pulley Housing, and pulleys from the top of tripod. (See Image 3 & 4)
Image 1
Image 2
Image 3 Image 4
Locking Pin
Locking Pin
Cotter Pin
Pulley
Pulley Housing Top of Tripod
(With pulleys removed)
User Manual
V1.0 2020 Copyright SafeWaze Page 8

Step 5: Install the Material Winch onto the tripod by placing the winch onto the pre-installed xture
plate of the tripod. Seat the hook of the winch bracket plate onto the cross bar of the tripod bracket.
(See Images 5 & 6)
Step 6: Rotate the winch assembly forward to allow for installation of the locking pin into the
pre-drilled holes in the winch bracket plate and the tripod bracket. (See Images 7 & 8)
Image 5
Image 7
Image 6
Image 8
Winch Bracket
Plate
Cross Bar of the
Tripod Bracket
Insert Locking
Pin
Hook of Winch Bracket
Plate seated onto
crossbar of Tripod Bracket
Tripod Fixture
Plate
Rotate Forward
Winch Bracket
Plate Hook
Winch
Step 7: Rotate the handle of the winch counter-clock wise to release the steel cable. Continue to
release the cable until enough length allows for the snap hook to be dropped down through the top of
the tripod. (See Image 9 & 10)
Image 9 Image 10
User Manual
V1.0 2020 Copyright SafeWaze Page 9

Step 7: Extend cable and route through top of tripod. To extend the cable from the unit, pull the
function switch button out, and then pull the crank handle base outward from the 3-Way Housing.
(See Image 15a) This places the 3-way unit into it’s Self Retracting Device conguration. Pull out the
required amount of cable to drop through the head assembly of the tripod. Pulling out once again on
the function switch and pushing the base of the crank handle assembly inward places the unit into
Rescue/Recovery mode.(See Image 15b) Drape the cable over the top of the tripod and slide the
snap hook down through the opening in the top of the tripod where the pulley (previously removed in
Step 4) is normally seated. (See Image 16)
Step 5: Install the 3-Way onto the tripod by placing the 3-Way onto the pre-installed xture plate of
the tripod. Seat the hook of the 3-Way bracket plate onto the cross bar of the tripod bracket.
(See Images 5 & 6)
Step 6: Rotate the winch assembly forward to allow for installation of the locking pin into the
pre-drilled holes in the winch bracket plate and the tripod bracket. (See Images 13 & 14)
Image 11
Image 13
Image 12
Image 14
3-Way Bracket
Plate
Cross Bar of the
Tripod Bracket
Insert Locking
Pin
Hook of 3-Way Bracket
Plate seated onto
crossbar of Tripod Bracket
Tripod Fixture
Plate
Rotate Forward
Winch Bracket
Plate Hook
3-Way
User Manual
V1.0 2020 Copyright SafeWaze Page 10

Image 15a Image 15b
Image 16
Pull out on base of
crank handle assembly Push in on base of crank handle assembly
Pull out on function
switch button Pull out on function switch button
Step 8: Re-install the Pulleys, Pulley Housings, and Cotter Pins in the top of the Tripod ensuring the
the 3-Way cable is routed over, and properly seated on the pulley. (See Image 17)
Image 17 Pulley
Pulley 3-Way Cable
Material Winch
Cable
User Manual
V1.0 2020 Copyright SafeWaze Page 11

019-11003 Now Ready for Use
The 019-11005 (3-Way unit) allows for raising and lowering a person up to 310 lbs (140.61 kg) into,
or out of, a conned space envrionment or similar working situation. The 019-11005 (3-Way unit) can
also be used as a Self-Retracting Device. When being utilized as a Self Retracting Device, the snap
hook must be attached to the dorsal D-ring of a full body harness. When being utilized for recovery
operations, the snap hook can be attached to either the dorsal D-ring of a full body harness, or the
front rescue D-ring of a full body harness if so equipped.
019-11005 (3-Way unit)
To operate the 019-11005 (3-Way unit) the crank handle grip should be be extended. Grasp the crank
handle and crank handle grip simultaneously. Pull the crank handle grip outward from the handle and
rotate the handle grip until it extends outward and away from the 3-way housing.(See images 18-20)
The crank handle assembly of the unit determines which function is to be employed by either pulling
the handle outward from the body of the unit or pushing it into the body. The Crank Handle Assembly
position is changed by pulling out on the function switch button and either pushing in or pulling out on
the crank handle assembly. The handle assembly pushed into the body of the unit places the unit in
recovery mode,(See Image 21) whereas pulling the handle assembly out from the unit places in into
Self Retracting Device mode.(See Image 22)
019-11009 Material Winch
Operation of the 019-11009 Material Winch to lower or raise material into the work area is simply
accomplished by use of the crank handle on the unit. Clockwise operation of the crank handle raises
material, and counterclockwise operation lowers material. The 019-11009 Material Winch has a built
in internal brake that will not allow the load to slip when cranking in either direction is stopped.
Operation
User Manual
V1.0 2020 Copyright SafeWaze Page 12

User Manual
V1.0 2020 Copyright SafeWaze Page 13
Inspection
USER MUST KEEP INSTRUCTIONS AVAILABLE FOR REFERENCE. Record Date of First Use.
Prior to each use, inspect system for possible deciencies including, but not limited to,
corrosion, deformation, pits, burrs, rough surfaces, sharp edges, cracking, rust, paint buildup,
excessive heating, alteration, and missing or illegible labels. User MUST IMMEDIATELY remove the
019-11003 from service is defects or damage are found, or if exposed to forces of fall arrest.
Inspect work area to ensure that location is free of any damage including, but not limited to,
debris, cracking, rot, decay, structural deterioration, rust, and free from any hazardous materials.
User must conrm that work area to be utilized will support the application specic loads as
referenced within this instruction manual. Work area MUST be stable.
At least annually, a Competent Person other than the user must inspect the 019-11003 Conned
Space System.
Image 18
Image 21 Image 22
Image 20
Image 19
Pull Out on Crank Handle
Grip Crank Handle Grip in
Extended Conguration
Rotate Crank Handle Grip
With the handle pushed in, the unit functions in recovery mode. By turning the crank handle
clockwise, the cable is lowered. Turning the crank handle counterclockwise will raise the individual
up. When the crank handle is pulled out from the unit, it functions as a Self Retracting Device.
Crank Handle assembly pulled
out in Self Retracting Device
Conguration
Crank Handle assembly pushed
in in Rescue/Recovery
Conguration

019-11009 Material Winch inspection:
1. Crank handle must move freely, and must not interfere with any other component. Locking
mechanism must operate properly with no slippage of cable.
2. The cable from the unit should pay out and retract smoothly when rotating the handle in
the corresponding clockwise or counterclockwise direction.
3. Inspect entire length of winch cable for any damage including, but not limited to, fraying,
crushing, bird caging, chemical exposure, heat/welding spatter, and kinking. User should
always wear gloves when inspecting winch cable to prevent injury in the event of cable
damage.
019-11005 (3-Way unit) inspection:
1. Crank handle must move freely, and must not interfere with any other component.
User Manual
V1.0 2020 Copyright SafeWaze Page 14
Competent Person inspections must be recorded in the inspection table included in this manual as
well as the inspection table labels on each product individually. The Competent Person must place
his/her initials in the block which corresponds with the month and year that the inspection is
performed. All individual labels on equipment will be initialed in the same manner.
While conducting inspections, the Competent Person must consider all applications and hazards that
the equipment may have been subjected to while in use.
Prior to each use, the user must inspect and verify that each individual component of the 019-11003
system is safe for use.
019-11000 Aluminum Tripod inspection:
1. Inspect for bent or deformed tripod legs.
2. Inspect that all locking pins for tripod legs are present and functional.
3. Inspect triopod pulley assembly for any missing for damaged components including,
pulleys, cotter pins, and pulley housings.
4. Ensure that tripod feet are clear of any debris and undamaged so that they can pivot
freely.
5. Inspect tripod chain for any kinks, broken links, corrosion, chemical exposure or any other
damage.
6. Inspect entire unit for any bends, cracks, corrosion, chemical exposure, or any factor that
may e󰀨ect integrity of the tripod unit.

2. With the crank handle pushed into unit in recovery mode, the cable from the unit should
pay out and retract smoothly when rotating the handle in the corresonding clockwise or
counterclockwise direction.
3. With the crank handle pulled out from the unit in Self Retracting Device mode:
a. Pull the lifeline sharply to test locking function
b. Lifeline should lock and subsequently retract smoothly and completely back into unit
without hesitation or stoppage.
c. Inspect entire length of lifeline for any damage including, but not limited to, fraying,
crushing, bird caging, chemical exposure, heat/welding spatter, and kinking. User
should always wear gloves when inspecting lifeline to prevent injury in the event of
cable damage.
User Manual
V1.0 2020 Copyright SafeWaze Page 15
Inspection Log
Product lifetime is indenite as long as it passes pre-use and Competent Person inspections. User
must inspect prior to each use. Competent Person other than the user must complete formal
inspection at least annually. Competent person to inspect and initial table below:
Date of First Use:_______________
Date Inspection
Items Noted Corrective Action Initials
If equipment fails inspection
IMMEDIATELY REMOVE FROM SERVICE

User Manual
V1.0 2020 Copyright SafeWaze Page 16
Safety Information
Failure to understand and comply with safety regulations may result in serious
injury or death. Regulations included herein are not all-inclusive, are for
reference only, and are not intended to replace a Competent Person’s
judgement or knowledge of federal or state standards.
Do not alter or misuse equipment.
Workplace conditions, including, but not limited to, ame, corrosive chemicals, electrical shock, sharp
objects, machinery, abrasive substances, weather conditions, and uneven surfaces, must be
assessed by a Competent Person before fall protection equipment is selected.
The inspection of the workplace must anticipate where workers will be performing their duties, the
routes they will take to reach their work, and the potential and existing fall hazards they may be
exposed to. Fall protection equipment must be chosen by a Competent Person. Selections must
account for all potential hazardous workplace conditions. All fall protection equipment should be
purchased in new and unused condition.
Fall protection systems must be selected and installed under the supervision of a Competent Person,
and used in a compliant manner. Fall protection systems must be designed in a manner compliant
with all federal, state, and safety regulations. Forces applied to anchors must be calculated by a
Competent Person.
Harnesses and connectors selected must be compliant with manufacturer’s instructions, and must be
of compatible size and conguration. Snap hooks, carabiners, and other connectors must be
selected and applied in a compatible fashion. All risk of disengagement must be eliminated. All snap
hooks and carabiners must be self-locking and self-closing, and must never be connected to each
other.
A pre-planned rescue procedure is required in the event a fall occurs. The rescue plan must be
project-specic. The rescue plan must allow for employees to rescue themselves, or provide an
alternative means for their prompt rescue. Store rescue equipment in an easily accessible and clearly
marked area.
Training of Authorized Persons to correctly erect, inspect, disassemble, maintain, store, and use
equipment must be provided by a Competent Person. Training must include the ability to recognize
fall hazards, minimize the likelihood of fall hazards, and the correct use of personal fall arrest
systems.
NEVER use fall protection equipment of any kind to hang, lift, support, or hoist tools or equipment,
unless explicitly certied for such use.
Equipment subjected to forces of fall arrest must immediately be removed from use.
WARNING

User Manual
V1.0 2020 Copyright SafeWaze Page 17
Age, tness, and health conditions can seriously a󰀨ect the worker should a fall occur. Consult a
doctor if there is any reason to doubt a user’s ability to withstand and safely absorb fall arrest forces
or perform set-up of equipment. Pregnant women and minors must not use this equipment.
Physical harm may still occur even if fall safety equipment functions correctly. Sustained post-fall
suspension may result in serious injury or death. Use trauma relief straps to reduce the e󰀨ects of
suspension trauma.
Safety Information (cont)
Labels
322 Industrial Court Concord, NC 28025
[phone]
www.safewaze.com
019-11000
019-11001
019-11002
019-11003
019-11004
MATERIALS: Aluminum, Zinc Plated Steel
CAPACITY: 130-310 lbs. (59-140 kg)
WORKING LOAD
350 lbs. (159 kg) maximum
MEETS
ANSI Z359.4 & ANSI Z117.1
OSHA Requirements
01161a
CONFINED SPACE TRIPOD
1 2 3 4 5
Inspection
Year
WARNING: User must read and
understand all instructions provided
with this product at time of
shipment prior to use. Misuse of
this product or failure to follow
instructions may result in serious
injury or death. Make only
compatible connections.
USE: Tripod must be used on
generally level and solid footing.
Tripod leg chains should be
adjusted to remove slack to avoid
tripping hazard. Load must be
maintained inside chain perimeter
to prevent tipping. Do not allow
components of any fall arrest,
rescue, or personal suspension
system to contact sharp edges or
abrasive surfaces during use. Avoid
chemical, thermal, and/or electrical
hazards.
INSPECTION: Tripod must be
inspected prior to each use. This
product must be inspected by a
competent person at least every 6
months or more frequently in harsh
environments. Do not use if
inspection reveals damaged
components or defective condition
01161b
322 Industrial Court, Concord, NC 28025
P: [phone] or F: [phone]
WWW.SAFEWAZE.COM
Ø 138mm
3-WAY SELF RETRACTING
LANYARD, RESCUE
& DESCENT DEVICE
3-WAY SELF RETRACTING
LANYARD, RESCUE
& DESCENT DEVICE
ANSI Z359.14, ANSI Z359.4 & ANSI A10.32
OSHA 1910.66 & OSHA 1926.502
Inv #:019737
Fall Arrest Systems •Confined Space •Engineering •Rescue Systems
Ø 152.5mmInv #: 019733
019-11005
019-11005
WARNING: User must read and understand all
instructions, provided with this product at time of
shipment, prior to use.
DO NOT ATTEMPT TO SERVICE OR REPAIR THIS
UNIT! CONTACT SAFEWAZE™ FOR SERVICE OR
REPAIR INFORMATION.
USE: This is a single person fall arrester device. User
must ensure that any connection to anchorage is
properly secured prior to use. Full Body Harness is
required for use with this device. Avoid lifeline contact
with sharp or abrasive edges. Avoid chemical, thermal
and/or electrical hazards. This product is not suitable
for use with horizontal lifelines and horizontal
positioning. Fall clearances must be calculated by a
Competent Person prior to use. Avoid swing fall
hazards. Fall clearance calculation for this device is
based upon unit installed in an overhead vertical
position in-line with the user. Not to be used for leading
edge applications. For use by trained persons only.
INSPECTION: Device must be inspected prior to each
use. Inspect device per instructions to include Locking
Function Test (sharp pull test), retraction test, label
legibility, any evidence of damage or defects, or
missing components or parts. Inspect housing,
connectors, fasteners and full length of lifeline
component for any damage or defects. This product
must be inspected in accordance with the
manufacturer’s instructions. Unit must be removed
from service if exposed to fall arrest forces. Fall
indicator is a swivel indicating snap hook; immediately
remove unit from service if swivel indicating snap hook
is deployed.
Specifications:
Working length: 65 ft (19.81 m)
Material: 3/16 in galvanized steel cable; steel
hardware; solid aluminum housing
Capacity range: 130-310 lbs (58.96 kg-140.61 kg)
Average arresting force: 900 lbs (408.23 kg)
Max arrest force: 1800 lbs (816.47 kg)
Max arresting distance: 54 in (137.16 cm)
Free fall limit: 24 in (60.96 cm)
Class B unit
65 ft Cable 3-Way Recovery Unit
1 2 3 4 5
Inspection
Year
MUST FOLLOW ALL MANUFACTURER’S INSTRUCTIONS
INCLUDED WITH THIS EQUIPMENT. DO NOT REMOVE LABEL.
INSERT MFG DATE AND SERIAL # HERE
WARNING
INSTALLATION
INSPECTION
65’ MATERIAL WINCH
DO NOT REMOVE LABEL
WARNING: USER MUST READAN FOLLOW INSTRUCTIONS SUPPLIED WITH THIS
EQUIPMENTAT TIME OF SHIPMENT. FAILURE TO DO SO MAY RESULT IN SERIOUS
INJURY OR DEATH. AVOID CONTACT WITH HAZARDS INCLUDING, BUTNOT LIMITED
TO, HEAT, CHEMICALS, ELECTRICITY, AND SHARP ORABRASIVE EDGES AND
SURFACES. MAKE ONLY COMPATIBLE CONNECTIONS. REFER TO INSTRUCTIONS
FOR APPROPRIATE INSTALLATION AND CONNECTION METHODS.
INSPECTION: User must inspect the unit prior to each use. A Competent Person must
perform an inspection of this unit at least annually. If equipment fails inspection IMMEDIATELY
REMOVE FROM SERVICE. Refer to the user instruction manual for complete inspection
procedures.
Attach the winch as specified in the user instructions. User must ensure that the cable end
connector is properly attached to the load. Rotate the handle of the winch counter clockwise to
lower the material, and rotate clockwise to raise material. Winch operator must maintain a
minimum of 15 lbs on the winch cable at all times while in use. Winch operator must remain in
visual or audible contact with personnel in a confined space at all times. This winch is
designed for lowering and hoisting MATERIAL only. Do not use this winch for lowering or
hoisting personnel. Refer to users manual for complete installation and use details.
[phone] www.safewaze.com
019771
019-11009
1 2 3 4 5
Inspection
Year
01161c

WARRANTY
SAFEWAZE™
322 Industrail Court
Concord, NC 28025
PHONE: [phone]
FAX: [phone]
EMAIL: [email protected]
Web: safewaze.com
User Manual
V1.0 2020 Copyright SafeWaze

Manual del usuario
V1.0 2020 Copyright SafeWaze Pág. 1
ADVERTENCIA
Este producto forma parte de un sistema personal de parada de caídas, posicionamiento de trabajo o rescate. Las
instrucciones del fabricante se le deben entregar al usuario de este equipo. El usuario debe seguir las instrucciones del
fabricante de cada componente del sistema. Antes de usar este equipo, el usuario debe leer y entender estas instrucciones.
El usuario debe seguir las instrucciones del fabricante para usar y mantener correctamente este equipo. Alterar o usar
incorrectamente este equipo, o no seguir las instrucciones, puede causar lesiones graves o muerte.
IMPORTANTE
Si tiene dudas sobre el uso, cuidado o idoneidad de este equipo para sus propósitos, comuníquese con SafeWaze.
IMPORTANTE
Registre el uso inicial del producto en la página 2 y en la página 15. Las inspecciones de la persona competente se deben
documentar en la tabla de registro de inspecciones de la página 15.
019-11003
Trípode con cabrestante de material de 65 pies
y dispositivo triple de 65 pies
2057

Manual del usuario
V1.0 2020 Copyright SafeWaze Pág. 2
ÍNDICE DE MATERIAS
1. INTRODUCCIÓN.............................................................................................. 3
2. NORMAS DE SEGURIDAD APLICABLES ....................................................... 3
3. DENOMINACIONES DE USUARIOS .............................................................. .3
4. CONFIGURACIONES ESPECÍFICAS DEL PRODUCTO................................. 4
5. LIMITACIONES................................................................................................. 4
6. COMPATIBILIDAD DE CONEXIONES............................................................. 5
7. FORMACIÓN DE CONEXIONES ..................................................................... 6
8. COMPONENTES Y ESPECIFICACIONES....................................................... 7
9. INSTALACIÓN Y USO................................................................................. 8-12
10. OPERACIÓN.............................................................................................. 12-13
11. INSPECCIÓN............................................................................................. 13-15
12. REGISTRO DE INSPECCIONES ................................................................... 15
13. INFORMACIÓN DE SEGURIDAD ............................................................. 16-17
14. ETIQUETAS.................................................................................................... 17
Datos del usuario
Fecha de la primera vez que usó el equipo:
Nro. de serie:
Capacitador:
Usuario:
¡No deseche estas instrucciones!
Antes de usar este equipo, el usuario debe leer y entender estas instrucciones.