Salamander EZ1/MS85/ML209 User manual

Salamander EZ-Touch Manual Lift Wall Mounts - EZ1/MS85/ML209 501-764 [12.22] page 1 of 9
USER MANUAL
EZ-Touch Manual Li Wall Mounts
EZ1/MS85/ML209
Consists of:
EZ1/MB16/209
EZ1/MA1
Displays up to 134-197 lbs (61-90 kg)
VESA Mounting: 200 x 200 - 800 x 670
Mount Body
VESA Bracket
EZ1_MS85_ML209 Instructions 12-20-22 - Cover Page
EZ1/MS85/ML209

Salamander EZ-Touch Manual Lift Wall Mounts - EZ1/MS85/ML209 501-764 [12.22] page 2 of 9
PARTS - EZ1/MS85/ML209
ML209
2x
ML209
C
M8 Split Washer (4x)
M4 x 12mm (10x)
M6 x 12mm (10x)
M8 x 10mm (10x)
M8 x 12mm (10x)
303-531- M8 x 65mm (4x)
P-301-170 - Display Spacer (4x)
400-171 - M6 Hex Key
EZ1_ML209 MSSH2 85 Instruction - Hardware
M8 Split Washer (4x)
M4 x 12mm (10x)
M6 x 12mm (10x)
M8 x 10mm (10x)
M8 x 12mm (10x)
303-531- M8 x 65mm (4x)
P-301-170 - Display Spacer (4x)
400-171 - M6 Hex Key
EZ1_ML209 MSSH2 85 Instruction - Hardware
A
B
2x
M8 Split Washer (4x)
M4 x 12mm (10x)
M6 x 12mm (10x)
M8 x 10mm (10x)
M8 x 12mm (10x)
303-531- M8 x 65mm (4x)
P-301-170 - Display Spacer (4x)
400-171 - M6 Hex Key
EZ1_ML209 MSSH2 85 Instruction - Hardware
M8 Split Washer (4x)
M4 x 12mm (10x)
M6 x 12mm (10x)
M8 x 10mm (10x)
M8 x 12mm (10x)
303-531- M8 x 65mm (4x)
P-301-170 - Display Spacer (4x)
400-171 - M6 Hex Key
EZ1_ML209 MSSH2 85 Instruction - Hardware

Salamander EZ-Touch Manual Lift Wall Mounts - EZ1/MS85/ML209 501-764 [12.22] page 3 of 9
How to use this manual
1 Read manual carefully before you install the mount
2 Carry out the actions fully and in the given sequence
3 The mount guarantee is voided if the product is not correctly installed or modified in any way
Warning symbols used
A Sharp edges
B Wear glove
C Physical load
D Two people required
E Entanglement hazard
F Warning: Can cause personal
injury or equipment damage
Intended use
The EZ-Touch Mount is a system that compensates the mass of vertically moving displays to ease
vertical movement of the display.
General warning
The display may only be attached to or removed from the EZ-Touch when the
EZ-Touch is in closed position. The EZ-Touch is under strong spring force. Only operate
the EZ-Touch with an adequately balanced display attached to the display frame.
Do not remove any parts of the EZ-Touch. Only the finishing cover can be removed.
Mounting fasteners
Mounting fasteners are not included with the product. Obtain advice from a specialist.
Setting the springs
Adjust only the outer springs:
• Adjust the height of the outer springs equally
• Make sure that the height of the display is balanced
• Increase the spring tension as much as possible
• Make sure that the display does not move up
Never adjust the inner springs
Disposal of the EZ-Touch
Springs should be unattached before disposal of the EZ-Touch. Sort the EZ-Touch,
the accessories and the packaging for the environmentally friendly recycling.
A
D E F
B C
Never adjust the inner springs!

Salamander EZ-Touch Manual Lift Wall Mounts - EZ1/MS85/ML209 501-764 [12.22] page 4 of 9
Mounting EZ-Touch Mount Body to Wall
Unpack the EZ-Touch and remove the plastic cover and two foam blocks.
Locating your mount
WOOD CONSTRUCTION:
locate two framing studs (minimum of 16” (405 mm) apart) at the desired location using a stud
finder device.
MASONRY:
a minimum width of 16” (405 mm) is required between fasteners.
Packing Foam
Block (2x)
Plastic Cover
Plastic Cover
Packing Foam
Block (2x)
Remove Plastic Cover and Foam Blocks
Installation of EZ1/MS85/ML209 Mount Body
Prepare Mounting Site
The EZ-Touch was designed to be installed on a 16” on center 2” x 4” wood stud, or metal studs, using
high-quality hollow wall anchor installed in the center of the stud
or a solid concrete wall.
WARNING: INSTALLING THE MOUNT IN UNDERRATED OR DAMAGED CONCRETE CAN LEAD TO
SERIOUS INJURY OR DAMAGE TO PRODUCT! When installing into concrete only install the mount in a
solid concrete wall made of 2500 PSI (17.3 MPa)
or stronger concrete. Never install the mount into cracked, chipped or flaking concrete.
WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! It is the installers responsibility to make sure the structure to which
the EZ-Touch is being installed is capable of supporting three times the combined weight of the EZ-Touch
and all
attached equipment is not to exceed the following weight capacities:
EZ1/MB16/152: 90-152lbs / 40-69kg

Salamander EZ-Touch Manual Lift Wall Mounts - EZ1/MS85/ML209 501-764 [12.22] page 5 of 9
406
16”
300
11.8"
LOCK SCREW HOLE
19
3/4"
Determine mounting height
See below for recommended mounting height for 55” Display. Other displays can be calculated by adding
half the height dierence to the top and half the height dierence to the bottom of the example shown.
42.5in
1079mm
16.00in
406mm
79.50in
2019mm
33.34in
847mm
91.82in
2332mm
Mounting
Bracket
Hole Position
Adjustable Range
Approx Lowest
Screen Position
MSSH2 85 Instruction - Determine Mounting Height
Mounting bracket level to wall
Unpack the EZ-Touch Take the wall bracket out (A) of the box. Note the slotted/slanted holes for
level wall mounting.

Salamander EZ-Touch Manual Lift Wall Mounts - EZ1/MS85/ML209 501-764 [12.22] page 6 of 9
Make sure screws are unlocked
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Lift the mount onto bracket
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm

Salamander EZ-Touch Manual Lift Wall Mounts - EZ1/MS85/ML209 501-764 [12.22] page 7 of 9
Lock mount with screws
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Level vertically with feet at the bottom

Salamander EZ-Touch Manual Lift Wall Mounts - EZ1/MS85/ML209 501-764 [12.22] page 8 of 9
Attach brackets to mount and display
Hang display onto horizontal bracket and level
M8 x 10mm (4x)
M4 x 12mm (10x) or
M6 x 12mm (10x) or
M8 x 12mm (10x)
P-301-170 (4x)
ML209 (2x)
M8 Split Washer (4x)
303-531 (4x)
EZ1_ML209 MSSH2 85 Instruction - Attach Brackets to Display
M6 x 12mm (4X)

Salamander EZ-Touch Manual Lift Wall Mounts - EZ1/MS85/ML209 501-764 [12.22] page 9 of 9
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Set balance
Never adjust the inner springs!
Balancing: Springs are always fully tightened for safety. Use a drill driver and 10mm socket,
rotate counter clockwise (loosen) evenly. Do three seconds left and three seconds right until the mount is
evenly balanced to support display weightlessly.
It may be necessary to tighten if balanced
point is exceeded.
SALAMANDER WARRANTY
LIMITED WARRANTY FOR COMMERCIAL VIDEO DISPLAY STANDS AND MOUNTS

Salamander warrants against manufacturing defects for two (2) years from the date of purchase. Salamander will repair or replace, at our option, any product
defective in materials or craftsmanship. Batteries are not covered by the warranty.
Full warranty including limitations and warranty claim information may be found at www.salamandercommercial.com
Subject to printing errors and technical amendments.
Lock display with safety lock screws from the bottom
M8 x 10mm (4x)
M4 x 12mm (10x) or
M6 x 12mm (10x) or
M8 x 12mm (10x)
10mm