Salamander UNIFI HUDDLE LITE UHL40A User manual

Salamander Uni Huddle Lite, Cafe, Single Mount 1 of 8 501-735 [11.21]
TIP HAZARD WARNING!
For use with video monitors weighing 175lbs (80kg) or less. Use with
heavier televisions may result in instability causing tip over resulting in
death or serious injury.
UNIFI HUDDLE LITE, CAFE - SINGLE MOUNT
UHL40A ASSEMBLY INSTRUCTIONS
LIMITED WARRANTY FOR COMMERCIAL VIDEO DISPLAY STANDS, MOUNTS AND HUDDLE
Salamander is proud to stand behind our products with industry-leading warranties. Should you ever encounter
any problem with your Salamander product, let us know. We are here to make it right. 1.860.761.9500
Full warranty including limitations and warranty claim information may be found at
www.salamandercommercial.com/warranty

Salamander Uni Huddle Lite, Cafe, Single Mount 2 of 8 501-735 [11.21]
warnings
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THIS FURNISHING
WARNING! – Failure to comply with these instructions may result in accident involving serious personal
injury. Failing to follow these instructions can result in the product being damaged or being destroyed or
voiding of the warranty.
WARNING! – For use with video monitors weighing 175lbs (80kg) or less. Use with heavier televisions
may result in instability causing tip over resulting in death or serious injury.
CAUTION!
• Close supervision is necessary when this furnishing is used by or near children, invalids,
or disabled persons
• Use this furnishing only for its intended use as described in these instructions.
Do not use attachments not recommended by the manufacturer.
• Do not use outdoors
• For Commercial Use Only
Weight Capacities – Max Load: D1/337AM1 - 175 lbs (80kg)
***** SAVE THESE INSTRUCTIONS *****
Accessories and Spare Parts
Please contact Salamander Designs 860.761.9500 or www.salamanderdesigns.com

Salamander Uni Huddle Lite, Cafe, Single Mount 3 of 8 501-735 [11.21]
1. ATTACH LEG AND MOUNT
301-265 (2x)
1/4-20 Joint Connector Nut
Modesty Panel fastens into
Support Post front channels
300-540 (4x)
Joint Connector Bolt
5/16-18 X 50 MM
300-518 (4x)
300-365
Support Posts
1/4-20 x 3/8 Button
Head Socket Cap Screws
Leveler
3/8-16 x 1.5” Stem

Salamander Uni Huddle Lite, Cafe, Single Mount 4 of 8 501-735 [11.21]
2. INSTALL CAMERA SHELF (OPTIONAL)
Attach the tech shelf and/or speaker/camera bracket by using the hardware in the locations shown above.
The weld nuts are to be located inside of the tech shelf mount post slot. Both the tech shelf and speaker/
camera bracket can be positioned either above or below the display.
Use Double-Sided Tape (M) to
secure device from sliding o shelf.
300-542 (2x)
Connector Bolt
5/16 18 x 1.5 Camera
Shelf
Camera
Mount Post
300-485 (2x)
1/4-20 x 1/2” Button Head
Socket Cap Screw
300-468 (2x)
1/4 Flat Washer
301-930
Speaker Bracket
301-010 (2x)
5/16-18 x 3/4”
Button Head Screw
300-520
Weld Nut, 1/4-20

Salamander Uni Huddle Lite, Cafe, Single Mount 5 of 8 501-735 [11.21]
3. MARK WALL FOR INSTALLATION
D. Line up the mounting holes in the desk with
the marked holes on the wall.
D
Mounting Locations
B
A
9.125
FLOOR
48” Desk Width
C37”
35.25”
B
A
9.125
FLOOR
48” Desk Width
C
28”
26.25”
Sitting Huddle LiteStanding Huddle Lite
A. Determine the location for the table and mark a vertical line indicating the center of the
table on the wall at 37” for standing table models or 28” for seated table models.
B. Draw 2 level horizontal lines through the line at 37” and 35.25 for standing tables or 28”
and 26.25 for the seated model.
C. From the centerline on both horizontal lines measure and mark 9.125” in 4 places
D. Verify locations with Table before installing wall fasteners.

Salamander Uni Huddle Lite, Cafe, Single Mount 6 of 8 501-735 [11.21]
Drill 1/2” diameter hole. Hold metal channel
flat alongside plastic straps and slide chan-
nel through hole.
Hold ends of straps between thumb and
forefinger and pull toward you until channel
rests flush behind wall. Slide plastic cap along
straps with either hand with flange of cap is
flush with wall.
Snap straps at wall by pushing side to
side,snapping of straps level with flange
of cap.
Move cabinet to wall and attach bracket.
Insert bolt through Bracket and tighten
until snug against wall.
Install wall fasteners to marked location on wall & fasten cabinet.
4. install WALL FASTENERS (most applications)
A B
C D
WOOD: Locate two framing studs using a stud finder device.
MASONRY: Place brackets in desired location.
Use a 3/16” [5mm] drill bit and drill holes 2.5” [64mm] deep.
4B. install WALL FASTENERS (ALTERNATE)
B
A
301-055
3/8 x 2” Alligator Wall Anchors
300-470
5/16” Flat Washer
301-730
5/16 x 2.5” Lag Bolt

Salamander Uni Huddle Lite, Cafe, Single Mount 7 of 8 501-735 [11.21]
5. COMPLETE WALL INSTALLATION
A. Place panel mount stretcher in position shown.
B.Mark two mounting points in slotted mounting location.
C.Remove stretcher and drill two 1/2” holes.
D. Attach stretcher to mount posts using four 303-524 screws as shown
below. Install the two wall fastener bolts through panel mount stretcher
into wall fastener.
303-524 (4x)
Socket Head Cap Screw
5/16-18 x 1”

Salamander Uni Huddle Lite, Cafe, Single Mount 8 of 8 501-735 [11.21]
6. install display brackets
Fasten the brackets using fasteners (length and size recommended by the display
manufacturer). Using improper screw length and size can damage the display.
NOTE: An assortment of screws and optional spacers have been provided in the PL100 kit.
Optional spacers are provided for additional clearance between the mount and the display,
if necessary.
6. install display
With the brackets now attached to the display, attach the display to the display
mount by inserting the shoulder washers through the upper, large diameter portion
of the teardrop shaped holes and gently allowing the four shoulder washers to seat
at the bottom of the teardrop shaped holes.