Salsbury Industries 18-51000 Series User manual

18” Wide Standard Lockers –18-51000 Series
Single Tier Installation Instructions
Thank you for selecting Salsbury’s 18” wide standard single tier lockers. These instructions are intended to assist you in assembling the lockers. Assembly of the various locker
components will be with #10 - 24 x 3/8” long slot less screws and #10 nuts (provided). Loosely fasten a screw and a nut into every set of mating holes with the screw heads positioned on
the outside of the locker or on the exposed surface.
One Wide Locker Assembly
Step 1: Attach the top shelf, bottom shelf, and the first single coat hook to the back
panel.
Step 2: Turn the back panel on its back with the shelves pointing upward. Attach the
first side panel, the left rear leg, and the hat shelf to the assembly from Step 1. Attach
a single coat hook with a double bend to accommodate the coat rod.
Step 3: Attach the second side panel and the right rear leg to the assembly of Step 2.
Attach a double bend for the third single coat hook and install the coat rod as shown
on page 3. The locker chassis is now complete.
Step 4: Attach the pre-assembled door frame onto the assembly of Step 3.
Step 5: Tighten all fasteners checking for squareness of the locker while tightening.
Attach optional sloping hood, end bases or front base (see pages 4 and 5).
Step 6: Place the locker in the installed location and anchor to the floor, wall, or to
both. Individual job conditions will dictate the type of fastening anchors to use (not
provided).
Step 7: Fasten all lockers in a row together by installing fasteners provided through
the side panels. Installation is now complete.

18” Wide Standard Lockers –18-51000 Series
Single Tier Installation Instructions
Three Wide Locker Assembly
Step 1: Attach a top shelf, a bottom shelf, and the first single coat hook to a back
panel.
Step 2: Turn the back panel on its back with the shelves pointing upward. Attach the
first side panel, the left rear leg, and the first hat shelf to the assembly of Step 1.
Attach a single coat hook with a double bend, this will accommodate the coat rod).
Step 3: Attach the second top shelf, the second bottom shelf, and an additional single
coat hook to the second back panel as in step 1.
Step 4: Simultaneously attach the assembly of Step 3 (second Step 1 assembly), the
second side panel, and the second hat shelf to the assembly of Step 2. Attach two
additional single coat hooks with a double bend and install a coat rod as shown on
page 3.
Step 5: Attach the third top shelf, the third bottom shelf, and an additional single coat
hook to the third back panel as in steps 1 and 3.
Step 6: Simultaneously attach the assembly of Step 5 (third Step 1 assembly), the
third side panel, and the third hat shelf to the assembly of Step 4. Repeat the Step 4
coat hooks instructions to attach additional coat hooks and coat rods.

18” Wide Standard Lockers –18-51000 Series
Single Tier Installation Instructions
Three Wide Locker Assembly (continued)
Step 7: Attach the last side panel and the right rear leg to the assembly of Step 6. On
15” deep lockers attach the last single coat hook. Attach a double bend and install the
last coat rod. The locker chassis is now complete.
Step 8: Position the pre-assembled door frames onto the assembly of Step 7 then
fasten one by one.
Step 9: Tighten all fasteners checking for squareness of the locker while tightening.
Attach optional sloping hoods, end bases or front bases (see pages 4 and 5).
Step 10: Place the locker in the installed location and anchor to the floor, wall, or to
both. Individual job conditions will dictate the type of fastening anchors to use (not
provided).
Step 11: Fasten all lockers in a row together by installing fasteners (provided) through
the side panels. Installation is now complete.
Coat Rod Installation

18” Wide Standard Lockers –18-51000 Series
Single Tier Installation Instructions
Sloping Hood Installation (Optional)
Step 1: Assemble the top panel to the rear panel with #10 - 24 x 3/8” slot less screws
and #10 nuts (provided). Position the flange of the top panel behind the rear panel.
Step 2: Assemble the side panels to the top panel and rear panel with #10 - 24 x 3/8”
long slot less screws and #10 nuts (provided).
Step 3: Attach the sloping hood to the top of the locker with #10 - 24 x 3/8” slot less
screws and #10 nuts (provided).

18” Wide Standard Lockers –18-51000 Series
Single Tier Installation Instructions
Front Base Installation (Optional)
Position the front base between the front legs of the locker with the flange upward.
Assemble to the locker with #10 - 24 x 3/8” slot less screws and #10 nuts (provided).
End Base Installation (Optional)
Position the appropriate end base (right or left) behind the corresponding side legs
(right or left) of the locker with the flange upward. Assemble to the locker with #10 - 24
x 3/8” slot less screws and #10 nuts (provided). Repeat for the other side.