Salter Labs SALTER AIRE Plus 8350 User manual

®
SALTER AIRE Plus COMPRESSOR
Model 8350 / 8352 / 8353
Instruction Manual
WARRANTY
Salter Labs warrants the SALTER AIRE PLUS ®Compressor to be
free from defects in workmanship and materials for a period of five
years from the date of purchase. Check with your dealer for more
details. This warranty is limited to the original purchaser of the com-
pressor. Any defective part or assembly will be repaired or replaced,
at the sole discretion and determination of Salter Labs, if the unit
has not been misused or tampered with during the period. Normal
maintenance items and disposable components are not covered by
this warranty. Shipping charges, if any, shall be paid by the pur-
chaser.
THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WAR-
RANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FIT-
NESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DU-
RATION OF THE EXPRESS LIMITED WARRANTY AND TO THE
EXTENT PERMITTED BY LAW AND ANY OTHER IMPLIED WAR-
RANTIES ARE EXCLUDED. THIS WARRANTY DOES NOT COVER
PROVIDING A LOANER COMPRESSOR, COMPENSATING FOR
COSTS INCURRED FOR COMPRESSOR RENTAL, OR FOR LA-
BOR COSTS INCURRED IN REPAIRING OR REPLACING A DE-
FECTIVE PART(S).
Thank you for selecting the SALTER AIRE PLUS ®
Compressor. Salter Labs is an innovative, industry-
leading manufacturer of respiratory care devices.
Please contact your local Salter Labs dealer for infor-
mation about additional products.
®
100 W. Sycamore Road
Arvin, California 93203 USA
Tel: [phone]
800-421-0024 (in CA)
800-235-4203 (outside CA)
Fax: [phone]
800-628-4690 (U.S. & Canada)
Internet: www.salterlabs.com
10
Salter Labs, Salter Aire Plus, NebuTech, and the Salter Labs logo are trademarks of Salter Labs
801562 Rev. G Released 3/2008
0482
Authorized Representative in the E.U.:
MT Promedt Consulting GmbH
Altenhofstrasse 80
D-66386 St. Ingbert
Germany
®
UL
US
C
LISTED

9i
SPECIFICATIONS
Specifications and appearance are subject to change without notice.
Dimensions: 17.0 cm L x 14.5 cm W x 11.2 cm H
(6.7” L x 5.7” W x 4.4” H)
Weight:
Model 8350 1.8 kg (4.0 lb)
Model 8352 1.9 kg (4.2 lb)
Model 8353 2.1 kg (4.6 lb)
Free Flow: 10 lpm minimum
Pressure: 25 psi minimum
Liter Flow: 6 lpm minimum through a Salter
Labs nebulizer
Ambient Temperature: 10 to 40°C (50 to 104°F)
Electrical: Shockproof
Model 8350 115 VAC, 60 Hz, 1.9 A
Model 8352 230 VAC, 50 Hz, 1.0 A (EU)
Model 8353 230 VAC, 50 Hz, 1.0 A (UK)
ACCESSORIES
Model Description
8501 Replacement Air Filters, 5 per pkg.
8504 Replacement Air Filter Cap, 1 each
8660 NebuTech®HDN®Nebulizer, 7’ Tubing - Reusable
8900 Nebulizer with Tee Adapter, 7’ Tubing, Mouthpiece
and Reservoir Tube
8906 Nebulizer, Pediatric Mask, 7’ Tubing
8924 Nebulizer, Adult Mask, 7’ Tubing
8960
NebuTech
®
HDN
®
Nebulizer, 7’ Tubing- Disposable
8966 NebuTech
®
HDN
®
Nebulizer, Pediatric Mask, 7’ Tubing
8984 NebuTech
®
HDN
®
Nebulizer, Adult Mask, 7’ Tubing
8258 Compressor Carrying Bag
TABLE OF CONTENTS
Introduction .................................................................................. 1
Important Safeguards .................................................................. 2
System Components .................................................................... 4
Setup and Operation .................................................................... 5
Setup ...................................................................................... 5
Operation ............................................................................... 5
Cleaning and Storage .................................................................. 6
Compressor Cleaning ............................................................ 6
Nebulizer Cleaning ................................................................. 7
Storage .................................................................................. 7
Maintenance................................................................................. 8
Filter Change ......................................................................... 8
Service ................................................................................... 8
Specifications ............................................................................... 9
Accessories .................................................................................. 9
Warranty ....................................................................................... 10
DEVICE INFORMATION
Record the following information for easy reference regarding
your SALTER AIRE PLUS ® Compressor.
Physician Name
Physician Phone
Dealer Name
Dealer Phone
Purchase Date
Type B Class II IPX0
Off / On
•
/

INTRODUCTION
Your physician has prescribed a liquid medicine to treat your
respiratory condition. In order to ensure high quality aerosol
nebulization, they have prescribed the SALTER AIRE PLUS ®
Compressor system from Salter Labs.
The SALTER AIRE PLUS ®Compressor generates compressed
air to turn your liquid medication into an aerosol mist that pen-
etrates into your lungs. Used in conjunction with a nebulizer
supplied by Salter Labs, you can be assured that you are us-
ing the finest quality products to deliver your medication.
To maximize your benefit from the SALTER AIRE PLUS ®
system, it is important for you to read and understand the
information in this instruction manual. By following your doctor’s
advice and these simple instructions, your SALTER AIRE
PLUS ®system will become a valuable part of your daily treat-
ment routine.
CAUTION – Use only as prescribed by your physician
with the prescribed medication. Read all warnings and
instructions before use. Improper use can result in se-
rious or fatal illness or injury.
CAUTION – Use only with nebulizers, masks, and tub-
ing supplied by Salter Labs. Other nebulizers, masks,
and tubing may result in improper treatment. One nebu-
lizer is provided with the compressor. Contact your lo-
cal dealer to obtain additional Salter Labs nebulizers.
CAUTION – Federal law (USA) restricts this device to
sale by or on the order of a physician.
1
MAINTENANCE
FILTER CHANGE
Your SALTER AIRE PLUS ®Compressor has an inlet air filter
to remove airborne contaminants. The filter requires periodic
replacement. The compressor comes with a package of extra
inlet filters for this purpose. Contact your local Salter Labs
dealer to obtain additional filters.
Check the inlet filter at least once a month. Follow these steps
to check and replace the filter if necessary.
1. Using a large coin, unscrew the filter cap on the front
panel and pull it out.
2. Remove the filter from the filter cap.
3. The filter should be changed if significant discoloration
is noticed around the middle of the filter or when it be-
gins to turn brown or gray in color. If required, insert a
new filter in the filter cap and discard the dirty filter.
Otherwise, reinsert the existing filter in the filter cap.
4. Screw the filter cap into position.
CAUTION – Compressor damage may result if filters
are reused or substituted with any other material.
SERVICE
Except for instructed user maintenance, all device servicing
must be performed by a Salter Labs authorized service repre-
sentative. There are no user serviceable parts inside the unit.
Contact your Salter Labs dealer or authorized service center if
your unit needs repair.
WARNING – Do not tamper with or attempt to repair
the device. Refer servicing to qualified service person-
nel.
8

IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS BEFORE USING
This electrical device has been designed to be shock-proof.
However, when using this device, especially when children
are present, basic safety precautions should always be fol-
lowed, including the following precautions.
DANGER – To reduce the risk of serious or fatal injury:
· Always unplug the device immediately after using.
· Do not use while bathing.
· Do not place or store the device where it can fall or be pulled
into a tub or sink.
· Do not place in or drop into water or other liquid.
· Do not reach for a device that has fallen into water. Unplug
immediately.
WARNING – To reduce the risk of injury or device damage:
· Use this device only for its intended use as described in
this manual. Use only with nebulizers supplied by Salter
Labs.
· Close supervision is necessary when this device is used
by, on, or near children or invalids.
· Never operate this device if it has a damaged cord or plug,
if it is not working properly, if it has been dropped or dam-
aged, or dropped into water. Return the device to a service
center for examination and repair.
· Turn the compressor off before filling the nebulizer with
medication.
· To prevent possible risk of infection due to contamination,
clean the nebulizer after each use according to its instruc-
tions.
· Never block the air vents on the rear and bottom of the de-
vice or place it where the vents may be blocked. Make sure
there is at least 15 cm (6 in) clearance on all sides of the
unit.
2 7
NEBULIZER CLEANING
Clean the nebulizer after each use. Refer to the cleaning in-
structions supplied with your nebulizer.
1. Ensure that the compressor is turned off and unplugged.
2. Disconnect tubing from the compressor and the nebulizer.
Set the tubing aside.
3. Disassemble and clean the nebulizer according to its in-
structions.
4. After cleaning, reassemble the nebulizer and tubing. Make
sure that the green cone is placed into the nebulizer cup
before assembling the top to the cup.
WARNING – To prevent possible risk of infection due to
contamination, clean the nebulizer after each use ac-
cording to the instructions.
STORAGE
1. Place the tubing and nebulizer in a clean, dry, sealed con-
tainer or bag.
2. Coil the power cord.
3. Store the compressor and nebulizer kit in a clean, dry envi-
ronment. If available, store and transport the device and
accessories in its carrying case. Do not store the com-
pressor on the floor where it can collect dust.
NOTE – The Compressor should be stored and transported
in the following environmental conditions:
Ambient temperature -40 to 70 °C (-40 to 158 °F)
Relative humidity 10 to 100 %
Atmospheric pressure 500 to 1060 hPa (375 to 795
mmHg)

2. Observe the nebulizer as the air flow begins. If you cannot
visually observe an aerosol mist coming out of the nebu-
lizer, replace it with another Salter Labs nebulizer.
3. Begin treatment by placing the nebulizer mouthpiece be-
tween your teeth. Close your mouth. Inhale deeply and
slowly as the aerosol begins to flow. Hold your breath for
several seconds, then exhale slowly.
4. If a Salter Labs aerosol mask is being used, position the
mask over your nose and mouth. Inhale deeply and slowly
through your mouth as the aerosol begins to flow. Hold
your breath for several seconds, then exhale slowly.
5. Continue treatment until aerosol mist is no longer coming
out of the nebulizer. Press the power switch to the off posi-
tion to turn the compressor off. Remove and clean the nebu-
lizer according to its instructions.
CAUTION – In high humidity conditions, water buildup
can occur in the compressor tubing. If this occurs, turn
the compressor on and run it for several minutes before
connecting the medication container.
CAUTION – Cold temperature may result in poor com-
pressor performance. Allow the unit to warm to room
temperature for best results.
CLEANING AND STORAGE
COMPRESSOR CLEANING
In order to maintain its performance, clean your SALTER AIRE
PLUS ®Compressor every two to three days.
1. Ensure that the compressor is turned off and unplugged.
2. Wipe the compressor with a clean, damp cloth. This
will keep the unit dirt and dust free.
CAUTION – Do not spray any fluid into the air vents of
the compressor. Fluids may cause damage to internal
components and could lead to a malfunction.
6 3
WARNING (continued)
· Do not operate the compressor while it is enclosed in a
carrying case or bag.
· If the device abruptly stops operating, check that the power
cord connection is secure. Also, see note below.
· Keep the cord away from heated surfaces.
· Never drop or insert any object into any opening or hose.
· Never use this device while sleeping or drowsy.
· Do not use outdoors. This device is for indoor use only.
· Do not tamper with or attempt to repair the device. There
are no user serviceable parts inside the unit. Except for
instructed user maintenance, all device servicing must be
performed by a Salter Labs authorized service center.
· Do not use this device in the presence of a flammable an-
aesthetic mixture with air or with oxygen or nitrous oxide.
· This device may generate, use, and radiate radio frequency
energy and, if not installed and used in accordance with
these instructions, may cause harmful interference to other
devices in the vicinity. However, there is no guarantee that
interference will not occur in a particular installation. If this
device does cause harmful interference to other equipment,
which can be determined by turning the device off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving device. In-
crease the separation between the equipment.
- Connect the device to an outlet on a circuit differ-
ent from that which the other device(s) are con-
nected.
- Consult your Salter Labs dealer or authorized
service center for help.
NOTE – The compressor employs an automatic reset thermal
limiter that shuts off the entire device if the motor over-
heats. The compressor will restart when the motor cools
to an acceptable level.
SAVE THESE INSTRUCTIONS

SYSTEM COMPONENTS
4
SETUP AND OPERATION
Follow these simple steps to prepare your SALTER AIRE PLUS
®
Compressor for operation. The instructions below describe use with
a nebulizer. If an aerosol mask is to be used, follow the assembly
instructions that come with the mask.
NOTE – Always wash your hands before you begin treatment.
NOTE – Always have at least two Salter Labs nebulizers on-
hand available for use.
SETUP
1. Remove the compressor from its (optional) carrying case. Place
the compressor on a level, sturdy surface. Make sure you can
reach the controls when seated. Press the power switch to the off
position.
CAUTION – Never block the air vents on the rear and bottom
of the device or place it where the vents may be blocked. Make
sure there is at least 15 cm (6 in) clearance on all sides of the
unit.
2. Plug the power cord into a power outlet.
3. Unpack the Salter Labs nebulizer and connect one end of the
tubing to the compressor’s outlet.
4. Assemble the nebulizer according to its instructions. Make sure
that the green cone has been placed into the nebulizer cup before
assembling the top to the cup.
CAUTION – Do not use a nebulizer if its green cone is miss-
ing. Utilize a new nebulizer if necessary.
5. Add the prescribed liquid medication to the top of the nebulizer
using an eyedropper, premeasured unit dose, or ampoule.
6. Attach the mouthpiece to the nebulizer.
7. Connect the tubing to the bottom inlet on the nebulizer.
OPERATION
1. Press the power switch to the (on) position to start the com-
pressor.
5
Mouthpiece
NebuTech™
HDN™
Nebulizer
Docking
Port
Tubing
Air Inlet Filter
Flow Outlet
ON / OFF
Switch
Power Cord
•