Sams ADVIN-1 Instruction manual

ADVIN-1
SDI / multiformat analog logo inserter
Copyright © 1999 - 2014 Sams elektronik d.o.o.
Published: 15. july 2008.
Updated: 03. november 2014.
Z10-3 edition 1
Code: 004.100
ENGLISH
Sams elektronik d.o.o.
48 Zivka Davidovica st.
11050 Belgrade
Serbia
Tel/Fax: [phone]
[phone]
[email protected]
www.sams.rs
Read the instructions before using the device.
Keep this manual for periodic usage.
USER MANUAL FOR USE AND MAINTENANCE

ADVIN
Inserters
elektronik
Sams elektronik d.o.o. • [email protected] • www.sams.rs
2
Dear User,
Thank you very much for purchasing our product.
Your purchase is a wise investment. The equipment you have purchased is manufactured with great care from
high-quality parts and materials. It is designed to fully meet the needs according to specications, if properly
installed, used and maintained according to the enclosed instructions.
Any technical failure or deciency that occurs during the warranty period specied on the invoice of the
purchased equipment will be inspected and serviced by Sams elektronik doo or an authorized service center of
the manufacturer, with the conditions set out in the warranty statement.
THIS DEVICE IS INTENDED FOR PROFESSIONAL USE.
WARRANTY STATEMENT
1. Product has declared characteristics. Within the warranty period, manufacturer ensures the removal of
technical failures, product defects or replacement of products if declared characteristics of the product are
changed.
2. If the goods are not delivered as specied with the contract, the consumer has the right to request from the
manufacturer / service provider to eliminate the lack of conformity, without charge, repair or replacement,
or to request an appropriate price reduction or terminate the contract.
3. Any repair or replacement must be made within a reasonable time without signicant inconvenience to
the consumer, taking into account the nature and the purpose for which the consumer has purchased the
product.
4. The consumer has the right to terminate the contract, if he can realize the right to repair or replacement,
or if the manufacturer / servicer has not completed repair or replacement within a reasonable time or if
the manufacturer / servicer did not perform repair or replacement without signicant inconvenience to the
consumer.
5. The consumer may not terminate the contract if the lack of conformity of the product is negligible.
6. The product will function properly when used in accordance with the user manual.
7. Period of servicing the product is 6 years from the launch on the market.
The product purchased outside the territory of Serbia does not fall under the terms of this warranty, only to 1
year factory warranty from date of purchase.
TERMS OF WARRANTY
1. The warranty period begins on the date of sale referred in the invoice.
2. The buyer loses the right to warranty if the defect cause failure from not following the user manual
instructions, improper installation, comes to mechanical damage during use, repairs and modications by
unauthorized persons, installation of non-genuine spare parts, and if the buyer does not comply with all
warnings listed in the user manual.
3. The warranty is voided if the device is damaged during the disturbances from the environment, natural
disasters (oods, hail, etc.), suffered an electric shock or lightning strike.
IMPORTANT NOTES
1. Be sure to thoroughly read the user manual.
If you have any doubts about the instructions, contact the technical support of the manufacturer.
2. Before contacting for technical help, please make sure that are provided with all necessary conditions for
normal operation.
3. If the malfunction or defect in the device does not eliminate within a reasonable time from the date of
failure, the warranty period shall be extended for as many days as the unit is in service.
4. For all maintenance interventions shall solely be authorized services listed in this Warranty Certicate.
WARRANTY

ADVIN
Inserters
Sams elektronik d.o.o. • [email protected] • www.sams.rs
elektronik
3
IMPORTANT SAFEY
WARNING
TO AVOID RISK OF FIRE OR ELECTRIC SHOCK
DO NOT EXPOSE THE UNIT TO MOISTURE OR RAIN
The symbol “lightning in a triangle” is to alert the user to the presence of
high voltage. In poor conditions the user may be exposed to shock.
The symbol “exclamation mark in a triangle” is to alert the user to comply by
the terms of use in user’s manual, which is supplied with the device.
SAFETY WARNINGS
ELECTRICAL SHOCK HAZARD
DO N OT O PEN
CAUTION
RIZIK OD S TRUJNOG UDARA
NE O TVARATI
DOK JE P OD N APONOM
UPOZORENJE
CLASS I DEVICE
Grounding is connected to the chassis of the device.
The power supply is protected with fuse against overload.

ADVIN
Inserters
elektronik
Sams elektronik d.o.o. • [email protected] • www.sams.rs
4
TECHNICAL SUPPORT AND SERVICE
Sams elektronik has made every effort to ensure that the equipment works in perfect condition. In
the event that problems that occur can not be resolved, or if you have any questions regarding this
equipment or information about other products produced from Sams elektronik, contact your local sales
representative or call Sams elektronik directly through one of the ways listed below:
Sales: [phone]
Technical support: [phone]
Service: [phone]
Email:
Sales - [email protected]
Technical support and service - [email protected]
Web site: www.sams.rs
Address:
SAMS ELEKTRONIK d.o.o.
48 Zivka Davidovica st
11050 Belgrade
Serbia
WARNING
TO AVOID ELECTRIC SHOCK, DO NOT OPEN COVER.
DEVICE MAINTENANCE REQUIRES PROFESSIONAL PERSON AUTHORIZED BY THE MANUFACTURER.
1. Read all safety and operating instructions before using the device.
2. Keep all safety and operating instructions.
3. Follow the instructions from the user manual.
4. Do not upgrade device, except in the case advised by the manufacturer.
5. Do not use the device in the presence of water and / or moisture.
6. Do not pour water or moisten the device with any type of liquid.
7. Openings on device are provided for ventilation.
8. Do not block air ow through the ventilation openings.
9. This product is powered by AC ~ 230V ± 10%, 50Hz.
10. This product is equipped with a three-wire cord with grounding.
11. This device is equipped with a protective fuse in the power outlet. Do not bypass fuse.
12. Do not replace the fuse. Replacement can be made by a person authorized by the manufacturer.
13. Do not bend the power cord so that it can be damaged.
14. Connect connectors as in the enclosed instructions. Deviations from the allowed values predicted
for the inputs and outputs of the device can cause severe damage and warranty void.
15. Do not use the device in an environment that contains ammable or explosive materials in any
physical state.
16. Turn off the power corde before cleaning. Do not use liquid, aerosol or ammable cleaners. Use
only a dry cloth.
17. Servicing is performed by a qualied person. Removing the cover user is exposed to high
voltages.
18. Never use the device when the cover is open and the device is powered on.
19. Do not expose to extreme high or low temperatures.
20. Do not expose to sudden temperature changes.
21. Call service in the following cases:
- The power cord or plug is damaged
- Liquid or foreign objects is inside the device
- The machine is exposed to water and moisture
- The device does not function according to specication
- The unit has been dropped or damaged
- The characteristics are signicantly changed
22. Use only specied replacement parts.
23. Professional person authorized by the manufacturer must check the device after completion of
service.
24. Allow a free rack unit (1RU) above and below the device for ventilation or put rack fan under the
device.
Pictures and drawings listed in this user manual are for information purposes only and may differ
from the actual device. Design and specications of the device may change without prior notice.

ADVIN
Inserters
Sams elektronik d.o.o. • [email protected] • www.sams.rs
elektronik
5
UNPACKING AND INSTALLATION....................................................................................6
MAINTENANCE..............................................................................................................6
REMOVAL AND STORAGE...............................................................................................6
DESCRIPTION...............................................................................................................7
INSTALLATION..............................................................................................................8
FUNCTIONS..................................................................................................................8
BLOCK DIAGRAM ..........................................................................................................10
NETWORK SETUP..........................................................................................................11
NETWORK ACCESS AND DEVICE CONTROL.....................................................................11
PLAYLIST SELECTION....................................................................................................12
LOGO CONTROL............................................................................................................12
LOGO POSITION ...........................................................................................................13
IMAGE PREPARATION FOR INSERTING...........................................................................13
PREPARATION OF THE LOGO.........................................................................................13
PAY ATTENTION BEFORE INSERTING LOGO....................................................................16
SOFTWARE...................................................................................................................17
REMOTE CONTROL........................................................................................................18
JOINT CONTROL OF INSERTERS ....................................................................................19
LCD TOUCH SCREEN - DESCRIPTION .............................................................................20
STATUS OF DEVICE .......................................................................................................20
MACRO STATUS ............................................................................................................20
MACRO CONFIGURATION ..............................................................................................21
GET LOGO ....................................................................................................................21
ADJUST LOGO LEVEL.....................................................................................................22
ADJUST HV POSITION...................................................................................................23
EDIT GPI ......................................................................................................................23
MACRO EDIT ................................................................................................................23
PLAY LIST.....................................................................................................................24
LOGO POSITION ...........................................................................................................25
LOGO LEVEL .................................................................................................................25
FADE IN TIME...............................................................................................................25
ADVANCED SETTINGS ...................................................................................................26
SC PHASE .....................................................................................................................26
H PHASE.......................................................................................................................26
SOFTWARE SUPPORT ....................................................................................................27
FRAMING......................................................................................................................27
PROBLEMS AND SOLUTIONS IN A NETWORK ENVIRONMENT ..........................................29
CABLE WIRING BETWEEN DEVICE AND REMOTE CONTROL.............................................31
CABLE WIRING FOR CONNECTION TO PC.......................................................................31
CABLE WIRING BETWEEN THE LOGO INSERTER AND DigiTIM-1 ......................................31
GPI / TALLY PINOUT......................................................................................................31
NOTES .........................................................................................................................32
PageDescription
TABLE OF CONTENTS

ADVIN
Inserters
elektronik
Sams elektronik d.o.o. • [email protected] • www.sams.rs
6
UNPACKING AND INSTALLATION
REMOVAL AND STORAGE
MAINTENANCE
The box contains:
- Device
- Power corde
- User manual (optional)
Before use, check the contents of the box. For any deciency report to the seller or the manufacturer
of the product.
DEVICE IS INSULATED BY PROTECTIVE WRAP AND PACKED IN A CARDBOARD BOX.
DEVICE IS SENSITIVE TO SHAKES AND DROPS. HANDLE WITH CARE DURING TRANSPORT
AND ASSEMBLY.
Check if the product is damaged during transport.
1. Before dismantling the device, switch off the power, remove
the power cord and remove all other connectors.
2. Remove the four screws for fastening.
3. Remove the device from rack cabinet.
4. Wrap the machine in the foil to protect it from dust. Package
it in a box.
5. The device must be stored in a room without moisture.
The system maintains only person authorized by Sams elektronik
doo.
Any voluntarily opening device, upgrading or servicing is strictly
prohibited and is subject to warranty void, and the possibility of
injury.
Places for fastening
PROCEDURES FOR SAFE USE OF THE DEVICE:
1. - Remove the protective wrap from the chassis.
- For devices that are AC 230V / 50Hz powered, the device is supplied with power cord.
- Use only power corde that comes with the device.
2. Device is mounted in a 19“ special-purpose rack cabinets designed for this type of device. Screw
device with four screws. Screws for fastening are not supplied with the device.
3. The device must be connected to ground. A device that is not connected to the grounding does
not function properly according to factory declarations and can cause adverse effects on users and
other equipment.
4. Strictly comply to all steps for proper connection of devices in the system.
Illustration - mounted device

ADVIN
Inserters
Sams elektronik d.o.o. • [email protected] • www.sams.rs
elektronik
7
DESCRIPTION
IV
1
INSERTERS
• Sams elektronik d.o.o. • 48 Zivka Davidovica st. • 11050 Belgrade • Serbia • • [phone]; [phone] • [email protected] • www.sams.rs •
ADVIN-1
SDI / multiformat analog motion logo inserter
- Power off / unit fail program video bypass relay (CVBS and SDI
only)
- High quality (10/21 bit)
- Programable hard or transparent key capability
- All four corner display capability
- Suport up to 229 independents logos
- Flash memory allows instant reprogrammability
- Analog preview output
- 7 preset animations
- Remote control panel with LCD touch screen
- Control of device via network trought web browser
- GPI control and TALY
TECHNICAL SPECIFICATIONS
GENERAL INFORMATION
- Code: ............................................................................... 004.100
- Weight: ................................................................................. 2 Kg
- Type: .................................................................... 1RU rack frame
- Dimensions: ....................................................1RU x 19” x 150mm
- Required: .............................................remote control IR-1 (IR-1a)
- Delivery includes: .........................device, power corde, user manual
SDI INPUT
- Number: .............................................. 1, BNC female, relay bypass
- Signal type: ......................................... Serial Digital (SMPTE 259M)
- EQ: ............................................................. Automatic up to 200m
- Impedance: ............................................................................ 75Ω
- Input level: ...............................................................800mV ±10%
SDI OUTPUT
- Number: .................................................................. 1, BNC female
- Signal type: ......................................... Serial Digital (SMPTE 259M)
- Impedance: 75Ω
- Jitter: ..............................< 0.2UI (Tipical 0.1UI @ Color Bar, 10Hz)
- Output level: .......................................................... 800mV ± 10%
COMPONENT ANALOG INPUT
- Number: ...............................3, BNC female (relay bypass for CVBS)
- Signal type: ............................. multiformat analog (CVBS, YUV, YC)
- Impedance: ............................................................................ 75Ω
COMPONENT ANALOG OUTPUT
- Number: .................................................................. 3, BNC female
- Signal type: ............................. multiformat analog (CVBS, YUV, YC)
- Impedance: ............................................................................ 75Ω
ORDERING INFORMATION
Code Name Description
004.100 ADVIN-1 SDI / analog logo inserter
Specications and designs are subject to change without notice
MONITORING OUTPUT
- Number: .................................................................. 1, BNC female
- Signal tpe: ............................................................................ CVBS
- Impedance: ............................................................................ 75Ω
REFERENCE INPUT
- Analog BB 300 mV: .................................................. 1, BNC female
TCP/IP
- Number: ............................................................................ 1, RJ45
GPI INPUT
- Number: ....................................................... 2, 5-pin terminal strip
- Function: ..............................Logo on/off, position, programmable...
TALLY
- Number: ....................................................... 2, 5-pin terminal strip
- Function-indication: ..................... Logo on/off, program input on/off
RS-232
- Number: .......................................................... 1, 9P SUB D female
- Function: ..................................................................Image upload
PERFORMANCE
- Bit Resolution: ....................................10 bit extended, 21 bit mixer
- Signal to Noise: ....................................................................60 dB
- Black offset: ............................................................. Self adjusting
- H adjustment range: ...........................................0-128 (37ns step)
- SC range: ...........................................................................0-360°
POWER
- Voltage: .............................................................~230V AC ± 10%
- Power: .................................................................................. 30W
- Frequency: ............................................................................50Hz
- Overload protection: ..........................front Mounted Circuit Breaker
TEMPERATURE
- Performance: ......................................................................5-40°C
- Operating: ..........................................................................0-50°C
The ADVIN-1 is device witch stores and recalls up to 229 individual,
dynamically positionable logos from multiformat analog or digital to
multiformat analog or digital program signal. It supports real-time play back of video, and can store animated logos lasting up to 9 seconds.
Inserter stores full bandwidth logos in high density ash memory that allows instant in-circuit reprogrammability. Logos sizes are 1/9th screen size
(256x128 pixel). The device have 7 independently direct access logo settings (macro’s). Every macro consist of a 230 steps deep play list and and
several programable settings. Every step in a play list contains information of currently displayed frame and step duration time (from 1 frame to
40 minutes adjustable). Play list can be programmed to run animation once or to make a loop or to make static logo. Programmable setting per
each macro are: transparency, fade-in time and position information for all four corners. Device can be controled with LCD touch screen remote
control, via network trought web browser on any OS or trough GPI control switch. Advanced users can create custom applications for controling
of device in playout sistems or some remote programming by sending special instructions. The device can be linked with DigiTIM-1 for some joint
functions, like ON/OFF and corner position. To protected your program signal against failure or power interruptions, a built-in bypass relay routes
the program input signal to the output (only for digital and CVBS) for uninterrupted operation. Pictures are uploaded with included Image Uploader
Software for PC or compatible. The device accepts Windows® 8-bit bitmap format.
front side
rear side

ADVIN
Inserters
elektronik
Sams elektronik d.o.o. • [email protected] • www.sams.rs
8
1
2
3
4
FUSE: 500mA
AC ~230V/50Hz
POWER
www.sams.rs
Made in Serbia
ADVIN-1r1
SN:
INPUTNETWORK
TCP/IP GPI / TALLY
PCREMOTE
PROGRAM
DIGITAL DIGITAL
INPUT OUTPUT
PROGRAM
PVW
EXT. REF.
R, V, CB, U, YG, Y
CVBS
CVBS
VUY CY
OUT
IN
USE ONLY WITH A 250V FUSE
INPUTNETWORK
TCP/IP GPI / TALLY
PCREMOTE
PROGRAM
DIGITAL DIGITAL
INPUT OUTPUT
PROGRAM
PVW
EXT. REF.
R, V, CB, U, YG, Y
CVBS
CVBS
VUY CY
OUT
IN
Rear side
Connectors on the rear side of the unit
Analog output
CVBS monitoring
Connector for connection
to the remote control
(be sure to connect
remote control
before power switch
is pressed)
Connector for connection to a PC
(RS-232)
TCP-IP
Connect the device to the local network.
Yellow LED lights up when
the cable is connected.
Green LED flashes
in communication with the device.
GPI
Connect the device
to the video mixer
SDI
input
SDI
output
Analog input
External reference input
Device supports signal generator (like Sams MSG-2).
NOTE
Presence of external
reference is mandatory!
If everything is OK, LEDs will illuminate
(depending on settings)
Front side
Multiformat analog / digital
motion logo generator inserter ADVIN-1
www.sams.rs
PGM
REF
GPI
RMT
PC
TCP/IP
Connect the power cord.
The device works only on AC ~ 230 V / 50 Hz.
Connect all necessary connectors
before the unit is turned on.
Turn on the device
by pressing the switch.
For best signal quality, use:
- Belden 1694A coaxial cable for SDI
- Belden 8281 coaxial cable for analog video
FUNCTIONS
1
1. TCP/IP (red LED) - LED ashes when in communication with the device.
2. PC (red LED) - when you put images into the device, the LED lights up, otherwise it is OFF.
3. RMT (red LED) - when connected to a remote control, the LED lights up, otherwise it is OFF.
4. GPI (red LED) - if the GPI cable is connected, the LED lights up, otherwise it is OFF.
5. REF (yellow LED) - if the reference cable is plugged in, LED lights up, otherwise it is OFF.
6. PGM (green LED) - if the PGM cable is connected, the LED lights up, otherwise it is OFF.
When device is ON:
PGM
REF
GPI
RMT
PC
TCP/IP
2 3 4 5 6
INSTALLATION

ADVIN
Inserters
Sams elektronik d.o.o. • [email protected] • www.sams.rs
elektronik
9
PROGRAM
DIGITAL DIGITAL
INPUT OUTPUT
PROGRAM
PVW
EXT. REF.
R, V, CB, U, YG, Y
CVBS
CVBS
VUY CY
OUT
IN
PROGRAM
DIGITAL DIGITAL
INPUT OUTPUT
PROGRAM
PVW
EXT. REF.
R, V, CB, U, YG, Y
CVBS
CVBS
VUY CY
OUT
IN
PROGRAM
DIGITAL DIGITAL
INPUT OUTPUT
PROGRAM
PVW
EXT. REF.
R, V, CB, U, YG, Y
CVBS
CVBS
VUY CY
OUT
IN
PROGRAM
DIGITAL DIGITAL
INPUT OUTPUT
PROGRAM
PVW
EXT. REF.
R, V, CB, U, YG, Y
CVBS
CVBS
VUY CY
OUT
IN
CVBS -> CVBS&YC
YC -> CVBS&YC
YUV -> YUV
SDI -> SDI
CVBS Y C PREVIEW
CVBS Y C PREVIEW
Y U V PREVIEW
PREVIEW
EXT. REF.CVBSSDI
OUT
EXT. REF.Y CSDI
OUT
EXT. REF.Y U VSDI
OUT
EXT. REF.SDI
OUT
SDI
IN

ADVIN
Inserters
elektronik
Sams elektronik d.o.o. • [email protected] • www.sams.rs
10
RS 485
GPI A
TALLY logo on
TALLY no signal
GPI B
RS 485 RS CPU
CPU LCD TP
KEYPAD LEDS
CABLE
CONTROL & LOGO UPLOAD
REMOTE CONTROL
ADVIN-1
RS 232
PC PC, MAC, SUN,
LINUX, OS/2,
PALM, MOBILE...
TCP IP
BB REF
CVBS PV OUT
12/10 bit
A/D
ANALOG
IN ANALOG OUT
R
G
B
Y
U
V
Y
CVBS
CVBS
only
BETACAM
C
Y
U
V
YCVBS
BETACAM
C
CONTROL &
PROGRAMING
WEB SERVER
CPU
FLASH LOGO STORE
FLASH
CPU SD RAM
LOGO
FILL
KEY MIXER
FADER
D/A
REF IN
GENLOCK
SC
PHASE
Color
processing DNR
D/A
SDI IN SDI OUT
SDI OUT
EDH & BB
SDI IN
EQ & PLL
BLOCK DIAGRAM

ADVIN
Inserters
Sams elektronik d.o.o. • [email protected] • www.sams.rs
elektronik
11
NETWORK ACCESS AND DEVICE CONTROL
The device can be congured through the web browser. First, the device must be found in the local
network. To do this, start the Sams Netnder software double clicking on the icon. The software rst
scans for devices.
Sams Netnder: scan for devices
When the search is completed, a new window will open showing found devices.
Sams Netnder: found devices
Click on the desired device and press the “Web Browser” located on the left side of the software.
Browser will display the conguration options.
NETWORK SETUP
To change the settings, consult your network administrator.
The default IP address is 192.168.0.200. If there is a DHCP server, the device will be assigned a new
address.
If there is a problem with connecting the device, check the rewall and allow UDP port 3040.
NOTE:
The device will be found from across the network only if the device was connected to a network cable
before turning on.
If the program NETFINDER does not nd the device on the network, try the following:
- Connect the inserter directly to the computer;
- The computer set with xed IP address, as follows:
IP ADDRESS 192.168.0.15
SUBMASK IP 255.255.255.0
IP GATEWAY left blank;
- Set REPAIR network card, in order to fully accept the new settings (alternatively RELEASE / RENEW
scenario);
- Try NETFINDER;
- The device must be seen;
- Write down the MAC ADDRESS and consult with the network administrator.
NOTE:
Do not use simultaneously with multiple places control over the network!
Just enter the correct value in the permitted range.
The manufacturer does not guarantee the validity of the results of irresponsible use of the device.

ADVIN
Inserters
elektronik
Sams elektronik d.o.o. • [email protected] • www.sams.rs
12
After a few seconds, the page will open.
Web browser: conguration
At the bottom of the page, you can see the status of the device.
PGM - Programming Input: If it’s green, it’s OK. If it is red, check cable or video source.
REF: if it is green, everything is OK. If it is red, check cable or reference source.
Device status is updated every 0.5 seconds.
PLAYLIST SELECTION
This is the option to select a precongured macros. By clicking on one of seven buttons, selected
will turn green. Selected macro can be seen even if it is changed from another computer or a remote
control.
LOGO CONTROL
This option includes:
- LOGO ON / OFF buttons - to control when the logo will appear on / off in the program signal.
- GET LOGO - select the logo that will be displayed in the program signal. Selecting this option turns
off the macro. The value is entered in the box next to the button, after which it is necessary to click
with mouse button (do nor press ENTER/RETURN).
- FADE IN - this option sets the effect of appearance of logo after pressing LOGO ON button. The
values are entered in the tenth of a second (1 sec = 10), and the maximum time is 25 seconds (250).
The value is entered in the box next to the button, after which it is necessary to click with mouse
button (do nor press ENTER/RETURN).
- Transparency - this option sets the level of transparency of logo. The value is within the range of 0
to 100. The value is entered in the box next to the button, after which it is necessary to click with
mouse button (do nor press ENTER/RETURN).

ADVIN
Inserters
Sams elektronik d.o.o. • [email protected] • www.sams.rs
elektronik
13
LOGO POSITION
This option includes:
- SELECT CORNER - this option controls in which corner of the screen will be the inserted logo
- PLACE SELECTION - this option controls the place of the inserted logo by control buttons up-down-
left-right.
- H-POSITION - This option controls the horizontal position of the logo by entering values. The value
is entered in the box next to the button, after which it is necessary to click with mouse button (do
nor press ENTER/RETURN).
- V-POSITION - This option controls the vertical position of the inserted image by entering values. The
value is entered in the box next to the button, after which it is necessary to click with mouse button
(do nor press ENTER/RETURN).
IMAGE PREPARATION FOR INSERTING
General rules:
1. The logo is preparing an application Adobe®Photoshop®.
2. The image size is 256x128px.
3. The logo is made in the RGB color palette.
4. he nal version of the logo is converted to an 8-bit palette (Indexed colors).
6. The nal version of the character is saved as BMP.
PREPARATION OF THE LOGO
The sign is (in principle) prepared in two ways. The rule, which is used depends mainly on ways how
logo was created.
1. Logo preparation in application Photoshop® (raster logo) requires that the logo must be originally
made for the size of the preparations for the inserter (we do not recommend this method):
- Open a new document sized 256x128px, 300dpi, transparent background.
- Open raster logo. The sign can not be scaled. It will lose quality.
- Position the logo in the middle.
- Convert to 8-bit palette (Indexed colors)
- Select logo (Ctrl+click on layer) -> Meni: SELECT -> INVERSE (Shift+Ctrl+I)
- Paint background in BLACK (R:0 G:0 B: 0)
- Save As BMP.
2. Logo preparation in application Photoshop® (vector logo):
(This variant is the most common and recommended as preparation)
- Open a new document sized 256x128px, 300dpi, transparent background.
- Open vector logo (Adobe Illustrator) in Photoshop®.
- Rasterize Generic PDF Format: Height: approximately 40-60px, resolution 300dpi, Mode: RGB,
Anti-aliased: on/off (this option gives different results, and allowed the user to decide which to use),
Constrain Proportions: ON -> OK.
- Transver logo to preparation window. Position the logo in the middle.
- Convert to 8-bit palette (Indexed colors)
- Select logo (Ctrl+click on layer) -> Meni: SELECT -> INVERSE (Shift+Ctrl+I)
- Paint background in BLACK (R:0 G:0 B: 0)
- Save As BMP.
SOFTWARE BUGs:
By selecting images in the Get LOGO, it is not possible later to return to the old macro. The only
solution is to choose another macro and then to return to the previous.

ADVIN
Inserters
elektronik
Sams elektronik d.o.o. • [email protected] • www.sams.rs
14
Picture 2
Logo on picture 2 is 40px height. In this case, the logo was in the vector format. Convert logo in 8-bit
color palette – Indexed colors (Picture 3).
Picture 3
Next, it will open Indexed Color options. On picture 4 are displayed setting. Select „Local (Selective)“
Palette. The most important thing is that to select an option Black and White in settings „Forced“. In
this way BLACK will be the key.
Picture 4
Logo edges will be without Anti-aliasing. Select layer (Ctrl+click on layer) -> Meni: SELECT -> INVERSE
(Shift+Ctrl+I)

ADVIN
Inserters
Sams elektronik d.o.o. • [email protected] • www.sams.rs
elektronik
15
Picture 5 - Selected layer
Picture 6 - Inverse selection
Paint background in black (R:0 G:0 B:0) (Picture 7)
Picture 7
Save As BMP
In BMP options select Windows File format and 8 bit Depth. Click on OK.

ADVIN
Inserters
elektronik
Sams elektronik d.o.o. • [email protected] • www.sams.rs
16
PAY ATTENTION BEFORE INSERTING LOGO
LOGO SIZE:
The most ideal logo size is 40-60px height (depending on the shape and proportions). Logo height / his
part necessarily have to be an even number in pixels. It is very important that the character would not
“icker” on the screen.
SAVE AS BMP
Saving logo is the most important process. Be sure to check the background color after conversion to 8
bit color palette. The rule is that the background is marked as Index 0 (Idx: 0). You can check this by
placing MOVE TOOL over background. If the background is at as shown in Picture 8, the preparation is
successful. It is recommended that the name of the image is no larger than 8 characters written in small
letters, in order to fully display name on the remote control and in order to prevent any system errors
caused by the inability to display certain characters.
Picture 8
NOTES:
Due to differences in the algorithm, for certain types of logos it is recommended to:
- Open prepared BMP le in the program Microsoft®PAINT
- Save As and overwrite an opened le.
If the appearance of the logo is not satisfactory:
- On left and right edges appears green and magenta - Change Aspect Ratio to 1.09 or change the width
of 2px.
- Parts of logo “icker” - correct logo in the parts that height have an odd number of pixels.

ADVIN
Inserters
Sams elektronik d.o.o. • [email protected] • www.sams.rs
elektronik
17
SOFTWARE
1. Exit from software
2. Selection of COM port
3. List of les in a folder
4. > Add selected images
>> Adding all of the images in folder
< Rejection of selected image
<< Rejection all images
5. List of selected images
6. Button to start inserting pictures in the inserter
7. Preview of selected image
8. Stopping the process of inserting images in the inserter
9. Expected time for nalization
10. Name of the image that is uploading
11. Images position in list
12. Information of uploading
13. Progress bar
14. Preview of uploaded image
15. Location in disc drive
After selecting the folder, select the image you want to upload in the inserter. If you want more images
at once use the CTRL key to select individual or SHIFT for group of images. After selecting press “>”. If
you want all images in the folder to add click on the button “>>”. After that, the software will ask from
SOFTWARE
INSTALLATION
- Start SETUP.exe from installation disc
- Follow instructions due installation.
CONFIGURATION
- OS Windows®
- VGA: 1024x768px
- 15” moniotor
- Pentium or compatible processor
- COM port that can support boud rate 38400.
1
2 3 4 5
6
7
8
9
10
11
12
13
14
15

ADVIN
Inserters
elektronik
Sams elektronik d.o.o. • [email protected] • www.sams.rs
18
REMOTE CONTROL
3
4
5
2
1
Rear side
Front side
NOTES:
- To make the device function properly, presence of external reference is mandatory.
- Do not upload images in the inserter immediately after turn on. Wait for it to nish initializing for
up to 2 minutes.
- Make sure that the inserter during images upload does not turn off.
- Not recommended that the rst letter of image name is the capital letters: L, C and R.
- Maximum number of uploaded images which can store is 229.
- Maximum number of uploads is 20.000, whether it is a single image or all 299.
- If it happens that the logo does not meet the quality or have some artifacts, reuplad the same
with the exact number as the previous one.
- BEFORE UPLOADING LOGO(S) INTO INSERTER UNPLUG TCP-IP CABLE FROM THE DEVICE!
- DURING UPLOADING LOGO(S) IN INSERTER, STOP ALL OPERATIONS THAT MAY AFFECT THE
EXECUTABLE FUNCTIONS OF THE DEVICE!
- After the device is switched off, and then on, the system initializes about 2 minutes. During this
period, the logos on the program output are not present, but loaded logos will be available on a
“preview” output.
LOGO
ON OFF
LOCK
POSITION
test_001
Inserter
Status
PGM Ok
Ref Ok
Step: 0
Logo: 0
test_001
HoldTime
00:00.00
H.Pos: 25
V.Pos: 40
LogoLvl: 80
test_001
test_001
test_001
test_001
test_001
test_001
Menu
Remote control panel for inserters IR-1
www.sams.rs
LOGO
ON OFF
LOCK
POSITION
test_001
Inserter
Status
PGM Ok
Ref Ok
Step: 0
Logo: 0
test_001
HoldTime
00:00.00
H.Pos: 25
V.Pos: 40
LogoLvl: 80
test_001
test_001
test_001
test_001
test_001
test_001
Menu
REMOTE CONTROL
1. 9-pin connector for connection with inserter
2. LCD touch screen
3. Panel lock key. After pressing this key, LCD screen turn off. To turn on again, press again
LOCK key.
4. Corner position keys. Each key calls the recorded position of the corresponding macro.
5. Keys for ON/OFF logo in program.
ON - to activate the logo in program with dened FADE IN time.
OFF - turn off logo from program
LOGO
ON OFF
LOCK
POSITION
test_001
Inserter
Status
PGM Ok
Ref Ok
Step: 0
Logo: 0
test_001
HoldTime
00:00.00
H.Pos: 25
V.Pos: 40
LogoLvl: 80
test_001
test_001
test_001
test_001
test_001
test_001
Menu
Remote controlpanel for inser ters VIN-11R
www.sams.rs
LOGO
ON OFF
LOCK
POSITION
test_001
Inserter
Status
PGM Ok
Ref Ok
Step: 0
Logo: 0
test_001
HoldTime
00:00.00
H.Pos: 25
V.Pos: 40
LogoLvl: 80
test_001
test_001
test_001
test_001
test_001
test_001
Menu
LOGO
ON OFF
LOCK
POSITION
test_001
Inserter
Status
PGM Ok
Ref Ok
Step: 0
Logo: 0
test_001
HoldTime
00:00.00
H.Pos: 25
V.Pos: 40
LogoLvl: 80
test_001
test_001
test_001
test_001
test_001
test_001
Menu
Remote controlpanel for inser ters VIN-11R
www.sams.rs
LOGO
ON OFF
LOCK
POSITION
test_001
Inserter
Status
PGM Ok
Ref Ok
Step: 0
Logo: 0
test_001
HoldTime
00:00.00
H.Pos: 25
V.Pos: 40
LogoLvl: 80
test_001
test_001
test_001
test_001
test_001
test_001
Menu
LOGO
ON OFF
LOCK
POSITION
test_001
Inserter
Status
PGM Ok
Ref Ok
Step: 0
Logo: 0
test_001
HoldTime
00:00.00
H.Pos: 25
V.Pos: 40
LogoLvl: 80
test_001
test_001
test_001
test_001
test_001
test_001
Menu
Remote controlpanel for inser ters VIN-11R
www.sams.rs
LOGO
ON OFF
LOCK
POSITION
test_001
Inserter
Status
PGM Ok
Ref Ok
Step: 0
Logo: 0
test_001
HoldTime
00:00.00
H.Pos: 25
V.Pos: 40
LogoLvl: 80
test_001
test_001
test_001
test_001
test_001
test_001
Menu
which number you want to upload images. If the inserter have pre-uploaded images, this can be useful,
in order to avoid numbers of this images (unless if you want to overwrite them). After prepared image
list, press the “UPLOAD FRAME(S)”. Images will then start to be uploaded into the inserter. One image
takes about 23 seconds to be uploaded into the inserter.

ADVIN
Inserters
Sams elektronik d.o.o. • [email protected] • www.sams.rs
elektronik
19
NOTE:
LCD screen is touch-sensitive. Take care during pressing on the screen. For pressing on the screen,
use only ngers.
Inadequate use of LCD touch screen is subject to warranty void.
Compatible devices can be connected via RS-232 connector.
In this way allows simultaneous switching from one corner to another and at the same time appear /
disappear. For easy reference, use the command IR-1d, which in 2RU panel has dual controls.
Version of remote control, without LCD display (IR-1a) has the option to choose the corner
and power on / off image. LOCK key in this version is called MACRO SELECT. By pressing
this button, you can select 6 macros. MACRO SELECT and active macro keys ashing. The
numbers next to the keys represent macro. Functions that are set via LCD screen, in this
version are set via web browser by sending commands.
JOINT CONTROL OF INSERTERS
LOGO
ON OFF
MACRO
SELECT
1 2
3 4
5 6
POSITION
Remote control panel for inserters IR-1a
www.sams.rs
LOGO
ON OFF
MACRO
SELECT
POSITION
5 6
3 4
1 2
LOGO
ON OFF
MACRO
SELECT
POSITION
5 6
3 4
1 2
Dual remote control panel for inserters
IR-1d
www.sams.rs
LOGO
ON OFF
LOCK
POSITION
TIME
DigiTIM-1
LOGO/TIME
ON/OFF
DigiVIN-1
ON OFF
LOCK
POSITION
test_001
Inserter
Status
PGM Ok
Ref Ok
Step: 0
Logo: 0
test_001
HoldTime
00:00.00
H.Pos: 25
V.Pos: 40
LogoLvl: 80
test_001
test_001
test_001
test_001
test_001
test_001
Menu

ADVIN
Inserters
elektronik
Sams elektronik d.o.o. • [email protected] • www.sams.rs
20
LCD TOUCH SCREEN - DESCRIPTION
During the initialization of the device (about 10 seconds) the display shows the manufacturer’s logo.
After initialization, the device displays the status and conguration macros.
test_001
Inserter
Status
PGM Ok
Ref Ok
Step: 0
Logo: 0
test_001
HoldTime
00:00.00
H.Pos: 25
V.Pos: 40
LogoLvl: 80
test_001
test_001
test_001
test_001
test_001
test_001
Menu
test_001
Inserter
Status
PGM Ok
Ref Ok
Step: 0
Logo: 0
test_001
HoldTime
00:00.00
H.Pos: 25
V.Pos: 40
LogoLvl: 80
test_001
test_001
test_001
test_001
test_001
test_001
Menu
Menu
Get Logo
Adjust
LogoLvl
Adjust
LogoLvl
Macro
Edit
Macro
Edit
Adjust
HV Pos.
Adjust
HV Pos.
Edit
GPI
Exit
1
1
PlayList
PlayList
Logo
Position
Logo
Position
Logo
Level
FadeIn
Time Exit
SC Phase
0/ 0
- 0 +
1 2 3
4 5 6
7 8 9
Select
input
CVBS
CVBS&Y/C
Select
outpit Exit
H. Phase
0
- 0 +
1 2 3
4 5 6
7 8 9
Exit
1
Edit LogoLvl
LogoLvl: 80
Show Exit
- 0 +
1 2 3
4 5 6
7 8 9
1
HV Position
H: 25
V: 40
Show Exit
< >
^
^
1
Device status in a simple way showing all the necessary information, such as:
- Status of the programming signal “PGM” - if in this status writes OK, everything is ne, and if it writes
ERROR, check the presence of the program signal. NOTE: Due to the loss of the program signal,
inserted logo will still be present on the background black. If a power is loss, relay protection will
override the programming signal to the output without interruption.
- Status of the reference signal “REF” - if in this status writes OK, everything is ne, and if it writes
ERROR, check the presence of a reference signal.
The device has seven conguration macros. Each macro can dene different style of inserted logo,
whether static or animated. Below the status of the program signal and the reference is printed
information of the status of the active macro.
Macro status describes:
STEP - represents currently active frame of animation.
LOGO - represents the number of currently active image. These are numbers that are dened during the
image uploading in the inserter. Below is the number of the currently active image.
HOLD TIME - time of active image. Time is reduced to zero, after which the display prints time of the
next step.
H. POS - represents the horizontal position of the currently active macro. Values are changing in relation
to the selected corner.
V. POS - represents the vertical position of the currently active macro. Values are changing in relation
to the selected corner.
LOGO LVL - is the level of transparency of currently active macro.
STATUS OF DEVICE
MACRO STATUS
When it is not used, LCD screen turn off after 2 minutes.
To activate it, touch with nger anywhere on the
screen.