Samsung scx-4100 series User manual

SERVICE
DIGITAL LASER MFP
SCX-4100
Manual
DIGITAL LASER MFP CONTENTS
1. Precautions
2. Reference Information
3. Specifications
4. Summary of product
5. Disassembly and Reassembly
6. Alignment and Adjustments
7. Troubleshooting
8. Exploded Views and Parts List
9. Block Diagram
10. Connection Diagram
fineline6

6
6
6-1
Samsung Electronics
Alignment & Adjustments
Service Manual
6. Alignment and Adjustments
This chapter describes some of the main service procedures including:
Using the EDC mode; Clearing paper jam and test patterns.
Much of this chapter is also included in the user's guide.
6.1 Engine Test Mode
The Engine Tests Mode supplies useful functions to check the condition of the engine. It tests the condition of
each device and displays the result of the test on the LCD. It is classified into 5 functions (0~4), and are shown
below.
6.1.1 To enter the Engine Test Mode
To enter the Engine Test mode
Press in sequence, and the LCD briefly displays
'Engine Test [Diagnostic]', the machine has entered Engine Test Mode.
• To enter a lower menu (Sub menu) Press the Start/Enter key.
• To exit into an upper menu Press the Menu/Exit key.
• To return to the user menu Press the Menu/Exit key.
6.1.2 Diagnostic
Menu/Exit Menu/ExitDarkness
Main Menu Engine test Remark
ENGINE TEST Motor Test 1 : On, 2 : Off
MTR FAN SOL ETC PickUp Test 1 : On, 2 : Off
Fan Test 1 : On, 2 : Off
Manual Clt Test 1 : On, 2 : Off
PTL Test 1 : On, 2 : Off
ENGINE TEST LSU Motor Test 1 : On, 2 : Off
LSU TEST LSU Hsync Test 1 : On, 2 : Off
LD Test 1 : On, 2 : Off
ENGINE TEST Feed Sen Test Check : Check Start
SENSOR TEST Next : Next Sensor Check
Exit Sen Test Check : Check Start
Next : Next Sensor Check
Cover Sen Test Check : Check Start
Next : Next Sensor Check
Empty Sen Test Check : Check Start
Next : Next Sensor Check
Manual Sen Text Check : Check Start
Next : Next Sensor Check
ENGINE TEST Therm ADC 220~85 1 : On, 2 : Off (maintain the fusing temp. 65C~230C)
HEAT TEST
ENGINE TEST MHV Test 1 : On, 2 : Off (-1550V ± 50V)
HVPS TEST Dev Bias Test 1 : On, 2 : Off (-430V ± 20V)
THV EN/NEG Test 1 : On, 2 : Off (-1000V +300V/-150V)
THV ON (1300V) 1 : On, 2 : Off (+1300V ± 20V)
THV ADC 1300V 1 : On, 2 : Off
THV ADC 600V~3550V 1 : On, 2 : Off (Compare each ADC Value)
fineline6

7
7
7-1
Samsung Electronics
Troubleshooting
Service Manual
7. Troubleshooting
7.1 Printing Problems – Causes and Solutions
7.1.1 Vertical Black Lines and Bands
• Description 1. Straight thin black vertical lines occur in the printing.
2. Dark black vertical bands occur in the printing.
Digital P inter
Digital P inter
Digital P inter
Digital P inter
Digital P inter
Check and Cause Solution
1. Damaged developer roller, deformed
Doctor-blade or cleaning-blade in the
Toner cartridge.
2. Scratched surface of the charge roller in
the toner cartridge.
3. 3. Depression or deformation of the
surface of the transfer roller.
1. Replace the toner cartridge and test
again.
2. Replace the toner cartridge and test
again.
3. Replace the transfer roller and test again.
7.1.2 Vertical White Line
• Description White vertical voids in the image.
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Check and Cause Solution
1. 1. Contamination of the window or
internal lenses of LSU mirror.
2. Foreign object inside the toner cartridge
or low toner.
3. Foreign object, contamination or burr on
the edge of the toner cartridge window.
4. If the fuser is defective, voids occur
periodically at the top of a black image.
5. Contamination of the OPC drum.
6. Depression or deformation of the surface
of the transfer roller
1. Clean the LSU window with recommended
cleaner (IPA) Clean the window with a
clean cotton swab. If dirt is inside the LSU
– replace LSU.
2. Replace the toner cartridge.
3. Clean the exposure window.
4. Open the front cover and check the ribs
that correspond to the position of the
voids. Remove if found.
5. If the problems are not solved, replace
the toner cartridge.
6. Replace the transfer roller.
fineline6

8
8
8-1
Samsung Electronics
Exploded View & Parts List
Service Manual
8. Exploded Views and Parts List
8.1 Main Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(8-2)
8.2 Frame Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(8-4)
8.3 Scanner Unit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(8-7)
8.4 Fuser Unit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(8-9)
8.5 Middle Cover Unit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(8-11)
8.6 Driver Unit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(8-13)
8.7 Cassette Unit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(8-14)
fineline6