Samsung SPF-72H User manual

| Safety Symbols | Power | Installation | Using and
Cleaning |
Safety Symbols
Make sure to follow the directions below to prevent accidents and damage to the product.
Failure to follow the accompanying directions may lead to serious injury or death.
Failure to follow the accompanying directions may lead to minor personal injury or property damage.
| Safety Symbols | Power | Installation | Using and
Cleaning |
Power
The images here are for reference only, and are not applicable in all cases (or countries).
Insert the power plug correctly until it is firmly in place.
zFailing to do so, may cause fire.
Do not use a damaged power plug, cord or outlet, as this may cause electric shock
or fire.
Do not touch the power plug with wet hands, as this may cause electric shock.

Do not connect more than one appliance to a single outlet, as an overheated outlet
may cause fire.
Do not use force to pull the power cord.
zDon't place anything heavy on the power cord, as this may cause electric shock or
fire.
Make sure to turn the power off and disconnect the power plug from the outlet
before moving the product. Make sure to disconnect the connection cables from
other devices as well.
zMoving the product without disconnecting the power cord may damage it while
moving, and may cause electric shock or fire.
Hold and pull out the plug by its body when disconnecting it from the outlet, as
pulling the plug out by the cord may cause it to be damaged.
zFailing to do so, may cause fire, or the product may not turn on normally.
Ensure that the power plug is disconnected before cleaning the product.
zFailing to do so, may cause electric shock or fire.
Do not let water come into contact with or enter the power adapter,as this may
cause electric shock or fire.
zDo not use the product outdoors in snowy or rainy weather, or near any water.
zWhen cleaning the floor with water, avoid any water contact with the power adapter.
Do not place the power adapter near a heater, as this may cause fire.

| Safety Symbols | Power | Installation | Using and
Cleaning |
Installation
When installing the product on a cabinet or shelf, do not let the front end of the
product project beyond its front edge.
zFailing to do so, may cause the product to fall, resulting in a product malfunction or
personal injury.
Do not place the power cord near a heater, as the power cord may melt, causing
electric shock or fire.
Do not install the product in a car or a location exposed to oil, smoke, moisture,
water, or rainwater.
zAny contact of these materials with the product may cause electric shock or fire.
Disconnect the power plug when there is thunder or lightning.
zFailing to do so, may cause electric shock or fire.
Place the product down gently when installing it.
zFailing to do so may cause product damage or personal injury.
Avoid dropping the product when moving, as this may cause product damage or
personal injury.
Do not install the product in a location easily reached by children.
zAs the product may fall and cause personal injury.

| Safety Symbols | Power | Installation | Using and
Cleaning |
Using and Cleaning
Do not insert any metal objects such as forks, wire, or gimlets, or flammable items
such as paper or matches into the ports at the back of the product, as this may
cause electric shock or fire.
zIf water or any foreign substance enters the product, make sure to turn the product
off disconnect the power plug from the outlet, and contact a service center.
Never disassemble, repair, or modify the product yourself.
zIf you need to repair your product, contact a service center. An attempt at repairing
this product may cause electric shock or fire.
If you hear a strange sound, smell anything burning, or see smoke, disconnect the
power plug immediately and contact a service center.
zFailing to disconnect the power plug may cause electric shock or fire.
Always remove dust and water from the pins and connections of the power plug.
zFailing to do so may cause electric shock or fire.
When cleaning the product, first disconnect the power plug and clean it with a soft,
dry cloth.
zDo not use any chemicals such as benzene, alcohol, thinners, mosquito repellant,
aromatic, lubricant, detergent or wax.
When not using the product for a long time, make sure to disconnect the power plug.
zHeavy accumulated dust may cause electric shock or fire.
If the product needs to be installed in a location that doesn't satisfy general
conditions, make sure to contact one of our service engineers about the installation
as the product may encounter serious quality problems due to its environment.
zThis refers to locations exposed to conditions such as heavy fine dust, chemicals, high or
low temperature, moisture, or when the product needs to be used continually without a
break over a long time.
If the product has been dropped or the product casing is damaged, turn it off and

disconnect the power plug.
zUsing the product without verifying that it has not been damaged may cause electric
shock or fire. Please contact a service center.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment) - Europe only
(Applicable in the European Union and other European countries with separate
collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed
with other household waste at the end of its working life. To prevent possible harm to the
environment or damage to health from uncontrolled waste disposal, please separate this from
other types of waste and recycle it responsibly to promote the sustainable reuse of material
resources.
Household users should contact either the retailer where they purchased this product, or their
local government office, for details of where and how they can take this item for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product should not be mixed with other commercial wastes for
disposal.

| Features | Components | Front | Back | Side
(Buttons) |
Features
Expand the memory capacity with a memory card. Enjoy stored images immediately.
By connecting a SD or MMC/MS/XD memory card of your digital camera to your digital photo frame, you can enjoy the
images on your digital photo frame quickly and easily. This also provides a way to expand the memory capacity of
your digital photo frame.
Stylish design
With its sleek and clean, high class design, your digital photo frame doubles as an ornament for your desk or table.
A 90 degree rotating stand allows both horizontal and vertical installations.
| Features | Components | Front | Back | Side
(Buttons) |
Please check that all components are contained in the delivered package.
If anything is omitted, contact the local distributor where the product was purchased. For optional items, contact a service center.
Never use a power adapter other than the adapter provided with the product.
Components

Digital Photo Frame
(Colors may differ for each product.)
Manual
Quick Start Warranty
(Not available in all locations) User Manual
Cables
Power cord USB cable
(A-B type) Power Adapter
Sold separately
SD/MMC/MS/XD card
| Features | Components | Front | Back | Side
(Buttons) |
Front
| Features | Components | Front | Back | Side
(Buttons) |

Back
Kensington lock
The Kensington lock is a device used to physically fix the system when using it in a
public place. (The locking device has to be purchased separately.)
For using a locking device, contact where you purchase it.
USB connection
terminal
Connect a PC or an external device using a USB cable.
Down stream
terminal
Connect your digital photo frame to a USB-supporting storage
device with a USB cable.(Compatible to USB 1.1)
Up stream
terminal
Connect your digital photo frame to a PC's USB terminal with a
USB cable. (Compatible to USB 2.0)
Make sure to use the USB cable (A-B type) provided with the product when
connecting your digital photo frame to a PC through the up stream terminal.
Power terminal
Connect the power adapter to this jack.
Connect the power cord to the power terminal of the power adapter.
Stand A 45, 90 degree rotating stand allows both horizontal and vertical installations. If your
digital photo frame is installed vertically, you can rotate your photos using the rotation
function to fit to the vertical installation.
Memory Card Slot You can insert a SD card or MMC/MS/XD card into this slot to view and use the content
stored on them.
SD/MMC cards larger than 2 GB may not be supported.
Sliding Prevention
Holder
Supports the product so that it stays firmly in place on slippery surfaces.
| Features | Components | Front | Back | Side
(Buttons) |
Side (Buttons)

[]PowerButton Turns the product on or off.
Power Indicator Connect the power cord to the power terminal of the power adapter.
Shows the power status. When the product is powered on, the power light turns
on.
[MENU] Menu Button Displays the menu at the bottom left corner of the screen.
[]UpButton Moves the selected frame in the menu up.
[ ] Left Button Moves the selected frame in the menu to the left.
[ ] Right Button Moves the selected frame in the menu to the right.
[ ] Down Button Moves the selected frame in the menu down.
[ENTER( )] Enter Button Selects a file to play back, a setting on the menu, or an item.
[▶ll] Play / Pause Button Play / Pause during playback.
[BACK] Back Button Return to the previous menu.

| Power | USB | Memory Card |
Connecting the Power
Connect the power adapter to the terminal at the back of the product.
Connect the power cord to the power adapter.
Plug the power cord for the product into a nearby outlet.
Press the button at the right of the product to turn the product on.
| Power | USB | Memory Card |
Connecting via USB

Down Stream
Terminal
Used to connect an external USB-supporting device to your digital photo frame.
If you connect your USB memory stick product to a USB hub or USB extension, it may not be
recognized. Therefore, make sure that the USB memory stick is inserted directly into the USB port.
When connecting an external device to the down stream terminal, use the USB cable provided with
the external device. (For more information on external devices and their cables, contact a relevant
service center.)
Samsung carries no liability for external device malfunctions caused by using any cable except
enclosed USB cable specified for each device.
Some external products provide a cable that does not meet USB standards.
Hence, they may cause a malfunction.
If an external storage device does not work normally when connected to your digital photo frame, try
to connect it to your PC. If it still does not work normally when connected to your PC, contact a
service center for that external device or your PC.
Up Stream
Terminal
Used to connect your digital photo frame to a PC.
When connecting your digital photo frame to a PC through the up stream terminal, make sure to use
the USB cable provided with the product.
Connect to the up stream terminal of your digital photo frame.
Connect the USB terminal of your PC.
| Power | USB | Memory Card |
Connecting a Memory Card

SD/MMC/MS/XD CARD Slide the card in the direction marked on the top of the card.
When the power is turned on, the Photo menu screen appears
automatically and a slide show starts with the photos in the Frame
Memory. If external memory, such as a memory card or USB memory, is
installed, it is selected first and a slide show starts with the photos in its
root directory. If there are no photo files, a list of folders is displayed.

When turning on the power, a slide show starts with the photo files in the root directory of the installed external memory
device. If there are no photo files or no external memory device is installed, the Photo menu screen is displayed.
If there are no key operations for five (5) minutes, the current mode changes to Clock mode to protect the screen. But Slide
Show mode has no change. If you press the MENU button in Clock mode, a sub menu is displayed. Press the BACK button to
return to the main screen.
| Buttons | Photo | Clock | Settings |
Buttons
Direct Functions
OSD Description
MENU Opens the on-screen menu and exits from the menu.
,,,These buttons allow you to adjust items in the menu.
ENTER Activates a highlighted menu item.
BACK Use this button to step one step back in the menu.
| Buttons | Photo | Clock | Settings |
Photo
When a folder is selected
When pressing the MENU, on-screen menu is displayed on the screen.

OSD Description
Open Open the folder.
Copy Copy the folder.
Delete Delete the folder.
When Thumbnail list is selected
When pressing the MENU, on-screen menu is displayed on the screen.
OSD Description
Start Slide Show Start slideshow.
Copy / Copy All files Copy the file.
Delete / Delete All files Delete the file.
Slide Show
When pressing the MENU, on-screen menu is displayed on the screen.
Only photos with a resolution of less than 8000 (width) * 8000 (height) pixels can be displayed on the screen.
Upper OSD
Sub OSD Detail OSD
Description
Start Slide Show Start slideshow
Slide Show Settings
Slide Show Effect Off , Fade, Shutter, Cross Comb, Mask, Brick,Dissolve, Bar, Expansion,
Silk, Random
Select an effect to give when displaying images on the screen.
Slide Show Speed Fast, Normal, Slow
Select a mode among Fast, Normal, and Slow.
Slide Show Repeat On, Off
Select the Repeat for displaying images.
Slide Show Shuffle On, Off
Select whether to playback the files sequentially or in shuffle mode.
Brightness
0~100
Adjust brightness from 0 to 100 levels.
Auto Rotation On, Off

If a photo is to be displayed in portrait mode while your Digital Album is placed horizontally, it is
automatically displayed rotated and fit to the width.
Rotate
Original, 90°, 180°, 270°
Select one among Original, 90°, 180°, and 270°.
Zoom
Original, x1, x2, x4
Select this if you want to zoom into a photo. You can magnify it to the x2 or x4 size.
The x1 size is when the photo is set to Fit to Width.
Aspect Ratio
Original, Fit To Width, Fit To Screen
Select an aspect ratio for images to display.
Direct Functions (Slide Show)
Button Status Description
>Pause slideshow Play the next file in the list. Show the information on the file
<Pause slideshow Play the previous file in the list. Show the information on the file.
[ ] Play slideshow.
[ ll ] Pause slideshow.
Show the information on the file
Pause slideshow. Play slideshow.
MENU Play slideshow
Pause slideshow
Pause slideshow. Show the menu on the file.
Exit the menu. Play slideshow.
| Buttons | Photo | Clock | Settings |
Clock
When pressing the MENU, on-screen menu is displayed on the screen.
Upper OSD
Detail OSD
Description
Time Format
12 Hours, 24 Hours
Enter and set 12 Hours, 24 Hours.
Date Format
YYYY/MM/DD, MM/DD/YYYY, DD/MM/YYYY
Select a Date Format.
Date and Time
set to 12 Hours
set to 24 Hours
Day, Month, Date, Year, Hour, Minute am/pm
Day, Month, Date, Year, Hour, Minute
Enter and set Month, Day, Year, Hour, Minute or am/pm. Whenever the power plug is disconnected, the
Date and Time information is lost. Therefore, you need to reset them each time.
On Timer
set to 12 Hours
set to 24 Hours
Activation, Hour, Minute, am/pm, Repeat
Activation, Hour, Minute, Repeat
Your product will turn on at the specified time automatically.
Off Timer
set to 12 Hours
set to 24 Hours
Activation, Hour, Minute, am/pm, Repeat
Activation, Hour, Minute, Repeat
Your product will turn off at the specified time automatically.

| Buttons | Photo | Clock | Settings |
Settings
Upper OSD
Detail OSD
Description
Language
English, Deutsch, Español, Français, Italiano, Nederlands, Polski, Português, Русский, Türkçe, 简󸖍
󷫥󷈪, 󷋍󷰍󷫥󷈪, 󷤓󷌨󷙲, 󳘱󰹂󲚉
Select a language to use for your product.
Auto Slide Show
Off, On
If On is selected, a slide show starts automatically when your monitor is turned on.
Brightness
0~100
Adjust brightness from 0 to 100 levels.
Firmware Update Update the product using an external memory(SD/MMC/MS/XD, USB).
Please visit www.samsung.com for the latest firmware update.
System Information
Model, Firmware Version
View the product information.
Reset Settings
Yes, No
Reverts the product settings to factory defaults.
I want to update firmware.
Preparations Digital Photo Frame
Firmware update file.
Please visit www.samsung.com for the latest firmware update.
USB memory card or external memory devices(SD/MMC/MS/XD)
Connect USB
memory card
to PC
If you are ready, connect the USB memory card to your PC.
Copy the firmware update file you downloaded to the USB memory card.
(Make sure to copy the firmware update file to the root directory.)
Connect USB
Memory Card
to Digital
Photo Frame
Remove the USB memory card from your PC, and connect it to your Digital Photo Frame.
If your Digital Photo Frame is off, turn it on.
Select Update Select Firmware Update of Settings.
Updating The update progression is displayed on the screen.
When the update finishes, turn your Digital Photo Frame off, remove the USB memory card,
and turn your Digital Photo Frame on again, for maximum safety.
Do not remove the USB memory card during the update operation.
Do not press any key during the update operation.
Do not insert any other card during the update operation.
Do not turn your Digital Photo Frame off during the update operation.
You can identify whether the update operation has finished successfully or not by checking the
firmware version of your Digital Photo Frame is changed to the version of the firmware update.

| Specifications | Supported Files |
Specifications
Items Specifications
Model Name SPF-72H
Panel
Type 7" (13 cm) TFT
Resolution 800 x 480
Brightness
200 cd/m2
Contrast Ratio 300 : 1
Interface RGB 6bit TTL
Supported Formats JPEG (RGB , Less than 8000x8000)
Progressive JPEG is not supported.
Operating System Windows 2000(SP2), Windows XP,
MAC OS X(10.x), Linx OS (2.6.x)
Built-in Memory 128 MB
USB One upstream (device 2.0) and one downstream (host 1.1)
Memory Card SD/MMC/MS/XD
Power
Rating External DC power adapter (12V, 2A, 24W)
Consumption
Normal mode : under 12W, power saving mode : under 5W,
Power off mode : under 1W
Content Files Photo File Slide show Run / Slide Show Effect / Rotate / Thumbnail View
General
Dimensions
(WxHxD) 209.4 x 149.4 x 87.4 mm / 8.24 x 5.88 x 3.44 inch

Weight 550 g / 1.21 lb
The product design may differ according to the model, and specifications are subject to change without prior
notice for product performance enhancement.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential Use and can be
used in all areas including common residential areas. (Class B equipment radiates less electromagnetic
influences than class A equipment.)
| Specifications | Supported Files |
Supported Files
Resolution : Less than 8000x8000
Supported image file format : JPEG (not supported Progressive JPEG)