Samsung ES15A series User manual

TFT-LCD MONITOR
ES15A*/ES17A*
Manual
SERVICE
TFT-LCD MONITOR CONTENTS
1. Precautions
2. Product Specifications
3. Disassembly & Reassembly
4. Alignment & Adjustments
5. Troubleshooting
6. Exploded View & Parts List
7. Electrical Parts List
8. Block Diagram
9. Wiring Diagram
10. Schematic Diagrams
11. Panel Description

1-1-1 Warnings
1. For continued safety, do not attempt to modify the
circuit board.
2. Disconnect the AC power and DC Power Jack
before servicing.
1-1-2 Servicing the LCD Monitor
1. When servicing the LCD Monitor Disconnect the
AC line cord from the AC outlet.
2. It is essential that service technicians have an
accurate voltage meter available at all times. Check
the calibration of this meter periodically.
1-1-3 Fire and Shock Hazard
Before returning the monitor to the user, perform the
following safety checks:
1. Inspect each lead dress to make certain that the
leads are not pinched or that hardware is not
lodged between the chassis and other metal parts in
the monitor.
2. Inspect all protective devices such as nonmetallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacitor networks, mechanical
insulators, etc.
3. Leakage Current Hot Check (Figure 1-1):
WARNING: Do not use an isolation transformer during
this test.
Use a leakage current tester or a metering system
that complies with American National Standards
Institute (ANSI C101.1, Leakage Current for
Appliances), and Underwriters Laboratories (UL
Publication UL1410, 59.7).
Figure 1-1. Leakage Current Test Circuit
4. With the unit completely reassembled, plug the AC
line cord directly into a 120V AC outlet. With the
unit’s AC switch first in the ON position and then
OFF, measure the current between a known earth
ground (metal water pipe, conduit, etc.) and all
exposed metal parts, including: metal cabinets,
screwheads and control shafts. The current
measured should not exceed 0.5 milliamp. Reverse
the power-plug prongs in the AC outlet and repeat
the test.
1-1-4 Product Safety Notices
Some electrical and mechanical parts have special
safety-related characteristics which are often not
evident from visual inspection. The protection they give
may not be obtained by replacing them with
components rated for higher voltage, wattage, etc. Parts
that have special safety characteristics are identified by
on schematics and parts lists. A substitute
replacement that does not have the same safety
characteristics as the recommended replacement part
might create shock, fire and / or other hazards. Product
safety is under review continuously and new
instructions are issued whenever appropriate.
ES15A*/ES17A* 1-1
1 Precautions
Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as
electrical shock.
1-1 Safety Precautions
DEVICE
UNDER
TEST
TEST ALL
EXPOSED METAL
SURFACES
(READING SHOULD
NOT BE ABOVE 0.5mA)
LEAKAGE
CURRENT
TESTER
2-WIRE CORD
ALSO TEST WITH
PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED) EARTH
GROUND
!

1-2-1 General Servicing Precautions
1. Always unplug the unit’s AC power cord from the
AC power source and disconnect the DC Power
Jack before attempting to:
(a) remove or reinstall any component or assembly,
(b) disconnect PCB plugs or connectors, (c) connect
a test component in parallel with an electrolytic
capacitor.
2. Some components are raised above the printed
circuit board for safety. An insulation tube or tape
is sometimes used. The internal wiring is
sometimes clamped to prevent contact with
thermally hot components. Reinstall all such
elements to their original position.
3. After servicing, always check that the screws,
components and wiring have been correctly
reinstalled. Make sure that the area around the
serviced part has not been damaged.
1. Immediately before handling any semiconductor
components or assemblies, drain the electrostatic
charge from your body by touching a known earth
ground. Alternatively, wear a discharging wrist-
strap device. To avoid a shock hazard, be sure to
remove the wrist strap before applying power to
the monitor.
2. After removing an ESD-equipped assembly, place it
on a conductive surface such as aluminum foil to
prevent accumulation of an electrostatic charge.
3. Do not use freon-propelled chemicals. These can
generate electrical charges sufficient to damage
ESDs.
4. Use only a grounded-tip soldering iron to solder or
desolder ESDs.
5. Use only an anti-static solder removal device. Some
solder removal devices not classified as “anti-static”
can generate electrical charges sufficient to damage
ESDs.
4. Check the insulation between the blades of the AC
plug and accessible conductive parts (examples:
metal panels, input terminals and earphone jacks).
5. Insulation Checking Procedure: Disconnect the
power cord from the AC source and turn the power
switch ON. Connect an insulation resistance meter
(500 V) to the blades of the AC plug.
The insulation resistance between each blade of the
AC plug and accessible conductive parts (see
above) should be greater than 1 megohm.
6. Always connect a test instrument’s ground lead to
the instrument chassis ground before connecting
the positive lead; always remove the instrument’s
ground lead last.
6. Do not remove a replacement ESD from its
protective package until you are ready to install it.
Most replacement ESDs are packaged with leads
that are electrically shorted together by conductive
foam, aluminum foil or other conductive materials.
7. Immediately before removing the protective
material from the leads of a replacement ESD,
touch the protective material to the chassis or
circuit assembly into which the device will be
installed.
Caution: Be sure no power is applied to the
chassis or circuit and observe all
other safety precautions.
8. Minimize body motions when handling
unpackaged replacement ESDs. Motions such as
brushing clothes together, or lifting your foot from
a carpeted floor can generate enough static
electricity to damage an ESD.
1 Precautions
1-2 ES15A*/ES17A*
1-3 Electrostatically Sensitive Devices (ESD) Precautions
Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly
called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some field-
effect transistors. The following techniques will reduce the incidence of component damage caused by static electricity.
1-2 Servicing Precautions
WARNING: An electrolytic capacitor installed with the wrong polarity might explode.
Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions
section of this manual.
Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the
safety precautions, always follow the safety precautions.

2 Product Specifications
2-1 Specifications
LCD Panel TFT-LCD panel, RGB vertical stripe, normaly TFT-LCD panel, RGB vertical stripe, normaly
white, 15-Inch viewable, 0.297 mm pixel pitch white, 17-Inch viewable, 0.264 mm pixel pitch
Scanning Frequency Horizontal : 30 kHz ~ 69 kHz (Automatic) 30 kHz ~ 81 kHz (Automatic)
Vertical : 56 Hz ~ 85 Hz (Automatic) 56 Hz ~ 76 Hz (Automatic)
Display Colors 16.7 Million colors
Maximum Resolution Horizontal : 1024 Pixels 1280 Pixels
Vertical : 768 Pixels 1024 Pixels
Input Video Signal Analog 0.7 Vp-p ± 5% positive at 75 Ω, internally terminated
Input Sync Signal Type : Seperate H/V Sync-on-Green,
automatic synchronization without external switch of sync type
Level : TTL level
Maximum Pixel Clock rate 95 MHz 135 MHz
Active Display
Horizontal/Vertical
AC power voltage & Frequency AC 90 ~ 264 Volts, 60 / 50 Hz ± 3 Hz
Power Consumption 40 W (Max) 52 W (Max)
Dimensions
Unit (W x D x H) 18.6 x 15.6 x 8.0 Inches (474 x 397 x 204 mm)
20.8 x 17.6 x 8.0 Inches (529.2 x 447.7 x 204.4 mm)
Carton (W x D x H)
22.6 x 18.3 x 10.2 Inches (577 x 465 x 259 mm) 24.0 x 20.0 x 10.1 Inches (611 x 511 x 258 mm)
Weight 3.95 Kg (8.7 Ibs) 4.95 Kg (10.9 Ibs)
Environmental Considerations Operating Temperature : 50 °F ~ 104 °F (10 °C ~ 40 °C)
Humidity : 10 % ~ 80 %
Storage Temperature : -13 °F ~ 113 °F (-25 °C ~ 45 °C)
Humidity : 5 % ~ 95 %
TV System
Antena Input 75Ω, Coaxial Cable
– MAX Internal speaker Out : Right => 3W Right => 5W
Left => 3W Left => 5W
Sound Characteristic
– BASS Control Range : -12dB~ + 12dB
– TREBLE Control Range : -12dB~ + 12dB
– Headphone Out: RF => 5mW max (400m Vrms)
A/V => 10mW max (580 Vrms), Max Input sound: -9dBm
– Output Frequency (TBD) : RF => 80 Hz ~ 15 kHz
A/V => 80 Hz ~ 20 kHz
ES15A*/ES17A* 2-1
Item Description
ES15A* ES17A*
304.1 mm / 228.1 mm 338.1 mm / 270.1 mm
Tunning Frequency Synthesize
Color PAL, SECAM
Sound NICAM, A2 STEREO

2 Product Specifications
2-2 ES15A*/ES17A*
2-2 Pin Assignments
Sync
Type
Pin No.
Separate H/V Composite H/V Sync-on-green
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Red
Green
Blue
GND
GND (DDC Return)
GND-Red
GND-Green
GND-Blue
No Connection
GND-Sync./Self Test
GND
DDC Data
Horizontal sync.
Vertical sync.
DDC Clock
Red
Green
Blue
GND
GND (DDC Return)
GND-Red
GND-Green
GND-Blue
No Connection
GND-Sync./Self Test
GND
DDC Data
H/V-Sync.
Not Used
DDC Clock
Red
Green + H/V Sync.
Blue
GND
GND (DDC Return)
GND-Red
GND-Green
GND-Blue
Not Used
GND-Sync./Self Test
GND
DDC Data
Not Used
Not Used
DDC Clock
Sync
Type
Pin No.
DTV 15pin connector
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Red , Y
Green , Pb
Blue , Pr
GND
GND
GND-Red
GND-Green
GND-Blue
GND
No Connection
GND
No Connection
Horizontal sync.
Vertical sync.
No Connection

2 Product Specifications
ES15A*/ES17A* 2-3
QRS
P
O
Video
Sync Sync
Horizontal Vertical
CDE
P
O
B
A
Video
Sync Sync
Separate Sync
2-3 Timing Chart
This section of the service manual describes the timing that the computer industry recognizes as standard
for computer-generated video signals.
C D
AO
E
BP
Video
Sync Sync
Video
Q R S
A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width
C : Back porch D : Active time Q : Back porch R : Active time
E : Front porch S : Front porch
VIDEO
A
BO
P
QRS
Horizontal Vertical
B
Green
Vertical
PQRS
O
Horizontal
H/V Composite Sync
Sync-on-Green
79.976
12.504
1.067
1.837
9.481
0.119
75.025
13.329
0.038
0.475
12.804
0.013
135.000
Positive
Positive
Separate
81.129
16.640
6.400
2.880
3.200
76.106
10.660
0.080
3.200
0.020
135.000
Negative
Negative
Com.
68.677
14.561
1.016
2.201
10.836
0.508
84.997
11.765
0.044
0.524
11.183
0.015
94.500
Positive
Positive
Separate
1024/85Hz
1024x768
1280/76Hz
1280x1024
1280/75Hz
1280x1024
1024/75Hz
1024 x 768
60.023
16.660
1.219
2.235
13.003
0.203
75.029
13.328
0.050
0.466
12.795
0.017
78.750
Positive
Positive
Separate
31.469
31.777
3.813
1.589
26.058
0.318
70.087
14.268
0.064
0.858
13.155
0.191
28.322
Negative
Positive
Separate
fH (kHz)
A µsec
B µsec
C µsec
D µsec
E µsec
fV (Hz)
O msec
P msec
Q msec
R msec
S msec
Clock
Freq.
(MHz)
Polarity
H.Sync
V.Sync
Remark
IBM
640/75 Hz
640 x 480
640/85 Hz
640 x 480
800/75 Hz
800 x 600
800/85 Hz
800 x 600
1024/60Hz
1024 x 768
VGA2/
70 Hz
720 x 400
VGA3/
60 Hz
640 x 480
Table 2-1. Timing Chart
31.469
31.778
3.813
1.589
26.058
0.318
59.940
16.683
0.064
0.794
15.761
0.064
25.175
Negative
Negative
Separate
37.500
26.667
2.032
3.810
20.317
0.508
75.000
13.333
0.080
0.427
12.800
0.027
31.500
Negative
Negative
Separate
43.269
23.111
1.556
2.222
17.778
1.556
85.008
11.764
0.671
0.578
11.093
0.023
49.500
Negative
Negative
Separate
46.875
21.333
1.616
3.232
16.162
0.323
75.000
13.333
0.064
0.448
12.800
0.021
49.500
Positive
Positive
Separate
53.674
18.631
1.138
2.702
14.222
0.569
85.061
11.756
0.056
0.503
11.179
0.019
56.250
Positive
Positive
Separate
48.363
20.677
2.092
2.462
15.754
0.369
60.004
16.666
0.124
0.600
15.880
0.062
75.000
Negative
Negative
Separate
Mode VESA
Timing (17” Only) (17” Only)

Memo
2 Product Specifications
2-4 ES15A*/ES17A*

3-1 General Alignment Instuction
1. Usually, a color TV-VCR needs only slight
touch-up adjustment upon installation.
Check the basic characteristics such as height,
horizontal and vertical sync.
2. Use the specified test equipment or its
equivalent.
3. Correct impedance matching is essential.
4. Avoid overload. Excessive signal from a
sweep generator might overload the front-end
of the TV. When inserting signal markers,
do not allow the marker generator to distort
test result.
5. Connect the TV only to an DC power source
with voltage and frequency as specified on
the backcover nameplate.
6. Do not attempt to connect or disconnect any
wire while the TV is turned on. Make sure
that the power cord is disconnected before
replacing any parts.
7. To protect aganist shock hazard,use an
isolation transform.
ES15A*/ES17A* 3-1
3 Disassembly and Reassembly
This section of the service manual describes the disassembly and reassembly procedures for the
ES15A*/ES17A* monitor.
WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling
these components.
3-1 Disassembly
Cautions:1. Disconnect the monitor from the power source before disassembly.
2. Follow these directions carefully; never use metal instruments to pry apart the cabinet.
1. After confirm there is nothing
on the desk
Turn the LCD module over
and put it on a flat desk set to
the ground.
3-2 Replacement Order of Lamp Assemblies

3 Disassembly and Reassembly
3-2 ES15A*/ES17A*
2. Push down the stopper and
slide the lamp unit.
3. Please take out the lamp
units from the LCD module.
4. Please fix the new lamp
units on the LCD module :
opposite process 2 and 3
3-3 Reassembly
Reassembly procedures are in the reverse order of Disassembly procedures.
* Replacement of lamp unit should be done at the power off state and recommended clean bench
condition.

ES15A*/ES17A* 4-1
4 Alignments and Adjustments
4-1 General Alignment Instuction
1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation.
Check the basic characteristics such as height, horizontal and vertical sync.
2. Use the specified test equipment or its equivalent.
3. Correct impedance matching is essential.
4. Avoid overload. Excessive signal from a sweep generator might overload the front-end
of the TV. When inserting signal markers,do not allow the marker generator to distort
test result.
5. Connect the TV only to an DC power source with voltage and frequency as specified on
the backcover nameplate.
6. Do not attempt to connect or disconnect any wire while the TV is turned on. Make sure
that the power cord is disconnected before replacing any parts.
7. To protect aganist shock hazard,use an isolation transform.

Memo
4 Alignments and Adjustments
4-2 ES15A*/ES17A*

ES15A*/ES17A* 5-1
5 Troubleshooting
5-1 No Power
Does proper DC 14 V appear at
DC jack connected to CN801? Check SMPS PCB and Adapter.
Yes
No
Does proper DC 5 V appear at
Pin 1 of IC803? Check IC803.
Check IC908.
Yes
No
Does proper DC 14V appear at
Pin 2 of IC803? Check IC803.
Yes
No
Does proper DC 3.3 V appear at
Pin 1 of IC804? Check IC804.
Yes
Yes
No
Does proper DC 2.5 V appear at
Pin 4 of IC105? Check IC105.
No

5 Troubleshooting
5-2 ES15A*/ES17A*
5-2 No Video (PC Signal)
Power indicator is green.
Does the signal appear
at C106, C107, C108
of R, G, B input?
Check CN100.
Yes
Yes
No
Does the clock pulse
appear at X100? Check X100 and related circuit of X100.
Yes
No
Does the clock pulse appear at
output of RA102 ~ RA107? Check related circuit of IC102.
Yes
No
Does the clock pulse
appear at R401? Check R401 and related circuit of R401.
Yes
No
Does the clock pulse appear at
output of R605 ~ R614? Replace R605 ~ R604.
Yes
No
Replace LCD Panel.

5 Troubleshooting
ES15A*/ES17A* 5-3
5-3 No Picture (TV, Video, S-Video, Scart Video)
Check Pin 71, 72 (S-Video)
and Pin 73 (VCR) and Pin 74
(Scart-Vin) and Pin 75 (RF-CVBS)
of IC201 (VPC3230D).
Check the CN806 (Tuner) and the
CN200 (Scart connector) and the
CN802 (VCR connector).
Yes
No
Does the signal appear at
RA200 ~RA203?
Check the IC201 (VPC3230D)
and related circuit of IC201.
Yes
No
Does the signal appear at
RA300 ~ RA303 of related
IC300 (FLI2200)?
Check the IC300 and
related circuit of IC300.
Yes
No
Check the IC400 and R422 ~ R426.

5 Troubleshooting
5-4 ES15A*/ES17A*
Does the signal appear at
Pin 67 (Tuner sound signal) and
Pin 57, 56 (PC sound) and Pin 51, 50
(VCR sound) and Pin 48, 47 (Scart
sound) of IC 700 (MSP3451)?
Check the CN803 (PC conector) and the
CN802 (VCR connector) and the CN200
(Scart connector and the CN806 (Tuner).
Yes
No
Does the signal appear at Pin 27,
28 of IC700 (MSP3451)?
Check the IC700 and
related circuit of IC700.
Yes
No
Does the signal appear
at L702 ~L705?
Check the IC702 (Audio amp) and
related circuit of IC702.
Yes
No
Replace the speaker.
5-4 No Sound

ES15A*/ES17A* 6-1
6 Exploded View and Parts List
6-1 ES15A*

6-2 ES17A*
6 Exploded View & Parts List
6-2 ES15A*/ES17A*

Item No Design LOC 품 명 Spec SERVICE
LW15E23CX/XEF
EA-LW15E23CX/XEF - 1 SEC,L06 -
BN90-00195E - ASSY STAND GH17LS SNA
6001-000154 STD+C/R SCREW-MACHINE BH,+,M4,L8,NI PLT,SWRCH18A,FP,-
BN75-00242A CIS UNIT-STAND EOS 15AS/NS,-,ABS,-,SV-012P,-,SPRAY,-
6003-000009 CIS SCREW-TAPTITE BH,+,B,M4,L16,ZPC(YEL),SWRCH18 SNA
6003-001010 CIS SCREW-TAPTITE FH,+,B,M3,L6,ZPC(YEL),SWRCH18A
6003-001315 CIS SCREW-TAPTITE BH,+,B,M4,L20,ZPC(YEL),SWRCH18A SNA
BH73-60339A CIS RUBBER-LEG SLC1400,EVA,GRAY,65HB,DIA13*H2 SNA
BN61-00159A CIS FRAME-STAND BASE EOS/NIKE,EGI,T1.2 SNA
BN61-00184A CIS STAND-BASE ES15AS,ABS PC,GR40,SV-012P SNA
BN72-00254A CIS STAND-COVER REAR EOS 15,ABS,HB,IV16,SPRAY SNA
BN72-00257A CIS STAND FRONT EOS 15,ABS,HB,16,SPRAY SNA
BN75-00211A CIS UNIT-HINGE EOS15,-,SECC T2.0,-,-,-,-,- SNA
BN90-00200A - ASSY COVER FRONT ES15AS SNA
6003-001319 C/F+C/R SCREW-TAPTITE BH,+,B,M3,L10,NI PLT,SWRCH18A,- SNA
BN90-00018F CIS ASSY COVER FRONT ES15AS,ABS HB,BRIGHT SILVER,SV-012P PAL
6002-000129 CIS SCREW-TAPPING FH,+,2S,M3,L8,ZPC(BLK),SM20C SNA
6003-000276 CIS SCREW-TAPTITE BH,+,B,M3,L10,ZPC(YEL),SWCH10 SNA
BN59-00214A CIS BOARD CN17VS,FUNCTION KEY,-,-,-,-,- SNA
BN59-00216A CIS PBA SUB CN17VS,IR PBA SUB,-,-,-,-,- SNA
BN59-00262A CIS SPEAKER SYSTEM EOS/NIKE15,EOS/NIKE15-R,100X42,WIRE:530MM SNA
BN59-00263A CIS SPEAKER SYSTEM EOS/NIKE17,EOS/NIKE17-L,100X42,WIRE:240MM SNA
BN64-00031A CIS BADGE-BRAND RB15AS,AL,T1.4,6.3,40.1,-,SILIVER,- SNA
BN64-00035A CIS KNOB-FUNCTION EOS15,ABS,IV16,-,-,HB,SPRAY,-,- SNA
BN64-00039A CIS GRILLE-SPEAKER EOS15,ABS ,T2.7,-,-,HB,IV16,SPRAY SNA
BN67-00020A CIS LENS-LED EOS15,ACRYL,CLEAR,-,-,-,-
BN72-00258A CIS COVER FRONT EOS15,ABS,HB,IV16,SPRAY SNA
BN90-00201A - ASSY COVER REAR ES15AS SNA
BN75-00238A CIS UNIT-REAR EOS 15,-,ABS,-,SV-012P,-,SPRAY,-
BN70-00176A CIS BRACKET VESA RB15AS,SECC,1 SNA
BN72-00259A CIS COVER-REAR EOS15,ABS,IV16,-,-,HB,-,-,SPRAY SNA
BN91-00220A - ASSY LCD ES15AS SNA
BN07-00053A CIS LCD LTM150XH-L06,CZB,6BIT_ FRC,331.6*254.76*12.5,16.19M,-,0.297*0.297,-,-,AMLCD/1 LV
BN91-00221A - ASSY SHIELD ES15AS SNA
0203-001160 CIS TAPE-FILAMENT SCOTCH#8915,T0.16,W48,L55M,TRP SNA
0203-001244 CIS TAPE-AL FOIL DK100-30-50,T40uM,W30,L50,SIL SNA
6003-000117 SH/PCB+FU/HAR SCREW-TAPTITE BH,+,B,M3,L6,ZPC(YEL),SWRCH18A SNA
6003-000276 C/F+AUD/PCB SCREW-TAPTITE BH,+,B,M3,L10,ZPC(YEL),SWCH10 SNA
6003-000276 C/F+B/GUIDE SCREW-TAPTITE BH,+,B,M3,L10,ZPC(YEL),SWCH10 SNA
6003-000276 C/F+SH/PCB SCREW-TAPTITE BH,+,B,M3,L10,ZPC(YEL),SWCH10 SNA
BN39-00202A CIS LEAD CONNECTOR-ASSY EOS,UL2835#28,UL/CSA,12P,-,-,#28,SMH200-12,12505HS-12,BK,-,-,200MM,2835#28,SJ01-
BN59-00215A CIS PBA SUB CN17VS,AV PBA FUNCTION,-,-,-,-,-
BN70-00192A CIS BRACKET-SUPPORT RB15AS,SECC,0.8 SNA
BN91-00222A - ASSY CHASSIS ES15AS
BN94-00259A - ASSY PCB MAIN ES15AS SNA
0202-001044 CIS SOLDER-WIRE. S63S-W3.0,S63S,D3,63Sn/37Pb,- SNA
0202-001046 CIS SOLDER-WIRE FLUX CF-110VH-2A,-,-,-,- SNA
0202-001222 CIS SOLDER-WIRE FLUX RS-107,RS60-1.2AA,D1.2,SN60/PB40,- SNA
0204-001095 CIS THINNER #4520,-,-,- SNA
1204-001904 IC203 IC-PAL DECODER SAA5264PS,SDIP,52P,600MIL,PLASTIC,3.6V,-,-20TO+70C,ST,IC-DECODER
2003-000797 R299 R-METAL OXIDE(S) 8.2ohm,5%,3W,AA,TP,6x16mm
Page 1

2201-000119 CIS C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP,8x3,5
2401-002286 C848 C-AL 470uF,20%,16V,WT,TP,10x12.5,5
2401-002286 C849 C-AL 470uF,20%,16V,WT,TP,10x12.5,5
2409-001044 C806 C-ORGANIC 100UF,+-20%,16V,WT,TP,8X10.5,5
2701-000116 L802 INDUCTOR-AXIAL 10uH,10%,4.2x9.8mm
2701-000146 BD810 INDUCTOR-AXIAL 2.2uH,10%,2.5x3.4mm
2701-000146 BD811 INDUCTOR-AXIAL 2.2uH,10%,2.5x3.4mm
3701-001219 CN100 CONNECTOR-DSUB 15P,3R,FEMALE,ANGLE,AUF
3704-000255 IC901_SOCK SOCKET-IC 32P,DIP,SN,2.54mm
3711-004270 CN700 CONNECTOR-HEADER BOX,2P,1R,2MM,ANGLE,SN SNA
3711-004386 CN701 CONNECTOR-HEADER BOX,3P,1R,2mm,ANGLE,SN SNA
3722-000117 CN801 JACK-DC POWER 3P,3.5MM,AG,BLK,NO SNA
3722-000183 CN200 JACK-SCART 21P,4mm,SN,BLK,NO
3722-001055 CN803 JACK-PHONE 5P/2C,3.6PI,AG,BLK,#16-22
6003-000117 IN/PCB+SH/PCB SCREW-TAPTITE BH,+,B,M3,L6,ZPC(YEL),SWRCH18A SNA
6003-000117 M/PCB+SH/PCB SCREW-TAPTITE BH,+,B,M3,L6,ZPC(YEL),SWRCH18A SNA
6003-000117 SH/PCB+SH/D_SUB SCREW-TAPTITE BH,+,B,M3,L6,ZPC(YEL),SWRCH18A SNA
BN39-00047A CIS CBF-HARNESS 100MM,100MM,BLU/WHT/GRY,UL1061,AWG28,51021-1200
BN39-00201A CIS LEAD CONNECTOR-ASSY ES15AS,UL2835#28,UL/CSA,6P,-,-,#28,12505HS-06,12505HS-06,BK,-,-,170MM,2835#28,SJ
BN39-00204A CIS LEAD CONNECTOR-ASSY ES15AS,UL2835#28,UL/CSA,20P,#30,12507HS-20,12507HS-20,BK,130MM,2835#28,SJ01-01-2
BN40-00005A CN806 RF MODULATOR-PAL TCPQ9091PD27D,PAL,-,-,-,5V,-10TO+65C,50DB,55DB
BN44-00056A CIS INVERTER GOGH,SIC1542,48KHZ,12VDC,1.5MARMS,5.6MARMS,48KHZ,37*140*16.0,4LAMP,40󰾝56KV,-,SIC
BN83-00065A U4 CKD-BN44-00056A BN44-00056A,1203-000560 SNA
BN83-00066A U1 CKD-BN44-00056A BN44-00056A,1201-000471 SNA
BN83-00067A U2 CKD-BN44-00056A BN44-00056A,1202-000104 SNA
BN83-00067A U3 CKD-BN44-00056A BN44-00056A,1202-000104 SNA
BN83-00067A U5 CKD-BN44-00056A BN44-00056A,1202-000104 SNA
BN83-00068A Q2 CKD-BN44-00056A BN44-00056A,0504-000158 SNA
BN83-00069A Q12 CKD-BN44-00056A BN44-00056A,0501-000457 SNA
BN83-00069A Q5 CKD-BN44-00056A BN44-00056A,0501-000457 SNA
BN83-00070A Q1 CKD-BN44-00056A BN44-00056A,0504-000129 SNA
BN83-00070A Q10 CKD-BN44-00056A BN44-00056A,0504-000129 SNA
BN83-00070A Q11 CKD-BN44-00056A BN44-00056A,0504-000129 SNA
BN83-00070A Q16 CKD-BN44-00056A BN44-00056A,0504-000129 SNA
BN83-00070A Q17 CKD-BN44-00056A BN44-00056A,0504-000129 SNA
BN83-00070A Q18 CKD-BN44-00056A BN44-00056A,0504-000129 SNA
BN83-00070A Q3 CKD-BN44-00056A BN44-00056A,0504-000129 SNA
BN83-00070A Q4 CKD-BN44-00056A BN44-00056A,0504-000129 SNA
BN83-00070A Q9 CKD-BN44-00056A BN44-00056A,0504-000129 SNA
BN83-00071A Q23 CKD-BN44-00056A BN44-00056A,0501-000462 SNA
BN83-00071A Q24 CKD-BN44-00056A BN44-00056A,0501-000462 SNA
BN83-00072A Q13 CKD-BN44-00056A BN44-00056A,0505-001160 SNA
BN83-00072A Q6 CKD-BN44-00056A BN44-00056A,0505-001160 SNA
BN83-00073A Q14 CKD-BN44-00056A BN44-00056A,0501-002186 SNA
BN83-00073A Q15 CKD-BN44-00056A BN44-00056A,0501-002186 SNA
BN83-00073A Q7 CKD-BN44-00056A BN44-00056A,0501-002186 SNA
BN83-00073A Q8 CKD-BN44-00056A BN44-00056A,0501-002186 SNA
BN83-00074A D10 CKD-BN44-00056A BN44-00056A,0407-000114 SNA
BN83-00074A D12 CKD-BN44-00056A BN44-00056A,0407-000114 SNA
BN83-00074A D19 CKD-BN44-00056A BN44-00056A,0407-000114 SNA
BN83-00074A D2 CKD-BN44-00056A BN44-00056A,0407-000114 SNA
BN83-00074A D20 CKD-BN44-00056A BN44-00056A,0407-000114 SNA
BN83-00074A D7 CKD-BN44-00056A BN44-00056A,0407-000114 SNA
BN83-00075A D13 CKD-BN44-00056A BN44-00056A,0402-001110 SNA
BN83-00075A D3 CKD-BN44-00056A BN44-00056A,0402-001110 SNA
Page 2

BN83-00076A D14 CKD-BN44-00056A BN44-00056A,0407-000122 SNA
BN83-00076A D4 CKD-BN44-00056A BN44-00056A,0407-000122 SNA
BN83-00077A D15 CKD-BN44-00056A BN44-00056A,0407-000116 SNA
BN83-00077A D16 CKD-BN44-00056A BN44-00056A,0407-000116 SNA
BN83-00077A D5 CKD-BN44-00056A BN44-00056A,0407-000116 SNA
BN83-00077A D6 CKD-BN44-00056A BN44-00056A,0407-000116 SNA
BN83-00078A C3 CKD-BN44-00056A BN44-00056A,2401-003400 SNA
BN83-00079A C14 CKD-BN44-00056A BN44-00056A,2301-001336 SNA
BN83-00079A C5 CKD-BN44-00056A BN44-00056A,2301-001336 SNA
BN83-00080A C15 CKD-BN44-00056A BN44-00056A,2201-002122 SNA
BN83-00080A C16 CKD-BN44-00056A BN44-00056A,2201-002122 SNA
BN83-00080A C6 CKD-BN44-00056A BN44-00056A,2201-002122 SNA
BN83-00080A C7 CKD-BN44-00056A BN44-00056A,2201-002122 SNA
BN83-00081A C1 CKD-BN44-00056A BN44-00056A,2203-000206 SNA
BN83-00081A C17 CKD-BN44-00056A BN44-00056A,2203-000206 SNA
BN83-00081A C18 CKD-BN44-00056A BN44-00056A,2203-000206 SNA
BN83-00081A C23 CKD-BN44-00056A BN44-00056A,2203-000206 SNA
BN83-00081A C50 CKD-BN44-00056A BN44-00056A,2203-000206 SNA
BN83-00081A C8 CKD-BN44-00056A BN44-00056A,2203-000206 SNA
BN83-00081A C9 CKD-BN44-00056A BN44-00056A,2203-000206 SNA
BN83-00082A C12 CKD-BN44-00056A BN44-00056A,2203-001458 SNA
BN83-00082A C21 CKD-BN44-00056A BN44-00056A,2203-001458 SNA
BN83-00083A C13 CKD-BN44-00056A BN44-00056A,2203-000455 SNA
BN83-00083A C22 CKD-BN44-00056A BN44-00056A,2203-000455 SNA
BN83-00084A C30 CKD-BN44-00056A BN44-00056A,2203-000590 SNA
BN83-00084A C31 CKD-BN44-00056A BN44-00056A,2203-000590 SNA
BN83-00085A C2 CKD-BN44-00056A BN44-00056A,2203-001130 SNA
BN83-00086A C10 CKD-BN44-00056A BN44-00056A,2203-002793 SNA
BN83-00086A C11 CKD-BN44-00056A BN44-00056A,2203-002793 SNA
BN83-00086A C19 CKD-BN44-00056A BN44-00056A,2203-002793 SNA
BN83-00086A C20 CKD-BN44-00056A BN44-00056A,2203-002793 SNA
BN83-00087A R19 CKD-BN44-00056A BN44-00056A,2007-000671 SNA
BN83-00087A R20 CKD-BN44-00056A BN44-00056A,2007-000671 SNA
BN83-00087A R45 CKD-BN44-00056A BN44-00056A,2007-000671 SNA
BN83-00087A R46 CKD-BN44-00056A BN44-00056A,2007-000671 SNA
BN83-00088A R2 CKD-BN44-00056A BN44-00056A,2007-001010 SNA
BN83-00089A R21 CKD-BN44-00056A BN44-00056A,2007-000794 SNA
BN83-00089A R22 CKD-BN44-00056A BN44-00056A,2007-000794 SNA
BN83-00089A R47 CKD-BN44-00056A BN44-00056A,2007-000794 SNA
BN83-00089A R48 CKD-BN44-00056A BN44-00056A,2007-000794 SNA
BN83-00089A R63 CKD-BN44-00056A BN44-00056A,2007-000794 SNA
BN83-00089A R66 CKD-BN44-00056A BN44-00056A,2007-000794 SNA
BN83-00090A R1 CKD-BN44-00056A BN44-00056A,2007-000098 SNA
BN83-00090A R23 CKD-BN44-00056A BN44-00056A,2007-000098 SNA
BN83-00090A R24 CKD-BN44-00056A BN44-00056A,2007-000098 SNA
BN83-00090A R29 CKD-BN44-00056A BN44-00056A,2007-000098 SNA
BN83-00090A R3 CKD-BN44-00056A BN44-00056A,2007-000098 SNA
BN83-00090A R49 CKD-BN44-00056A BN44-00056A,2007-000098 SNA
BN83-00090A R50 CKD-BN44-00056A BN44-00056A,2007-000098 SNA
BN83-00090A R55 CKD-BN44-00056A BN44-00056A,2007-000098 SNA
BN83-00091A R25 CKD-BN44-00056A BN44-00056A,2007-000096 SNA
BN83-00091A R52 CKD-BN44-00056A BN44-00056A,2007-000096 SNA
BN83-00092A R31 CKD-BN44-00056A BN44-00056A,2007-000872 SNA
BN83-00092A R34 CKD-BN44-00056A BN44-00056A,2007-000872 SNA
BN83-00092A R57 CKD-BN44-00056A BN44-00056A,2007-000872 SNA
Page 3