Samsung SyncMaster 194T User manual

SyncMaster 194T

Main Page On-Screen Display
Safety Instructions Troubleshooting
Notational Check List
Power Q & A
Installation Self-Test Feature Check
Cleaning
Other
Introduction Specifications
Unpacking General Specifications
Front PowerSaver
Rear Preset Timing Modes
Setup Information
Connecting the Monitor Service
Installing the Monitor Driver Terms
Automatic Regulatory
Manual Natural Color
Installing VESA compliant mounting For Better Display
Image Retention Free
Authority

Notational
Power
Installation
Clean
Other
Failure to follow directions noted by this symbol could result in bodily harm or damage to
equipment.
Prohibited Important to read and understand at all times
Do not disassemble Disconnect the plug from the outlet
Do not touch Grounding to prevent an electric shock

Notational
Power
Installation
Clean
Other
When notused foranextendedperiodof time,set your computer to DPMS.
If using a screen saver, set it to the active screen mode.
Do not use a damaged or loose plug.
zThis may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet
hands.
zThis may cause an electric shock or fire.
Use only a properly grounded plug and receptacle.
zAn improper ground may cause electric shock or equipment
damage.
Do not excessively bend the plug and wire nor place heavy objects
upon them.
zThis may cause an electric shock or fire.
Do not connect too many extension cords or plugs to an outlet.
zThis may cause fire.

Notational
Power
Installation
Clean
Other
Put your monitor in a location with low humidity and a minimum of
dust.
zAn electric shock or fire could result inside the monitor.
Do not drop the monitor when moving it.
zThis may cause damage to the product or human body.
Place the monitor on a flat and stable surface.
zThemonitor may causeinjury byfalling.
Set down the monitor carefully.
zThe monitor could be damaged or broken.
Do not place the monitor face down.
zThe TFT-LCD surface may be damaged.
Installing a wall bracket must be done by a qualified professional.
zInstallation by unqualified personnel may result in injury.
zAlways use the mounting device specified in the owner's manual.
Leave a space for ventilation between the product and the wall.
zPoor ventilation may cause the interior temperature to rise and lead
tofire.

Notational
Power
Installation
Clean
Other
When cleaning the monitor case or the surface of the TFT-LCD screen, wipe
with a slightly moistened, soft fabric.
Do not spray water or detergent directly on the monitor.
zThismay cause damage,electric shock or fire.
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty,
clean it properly with a dry cloth.
zAdirty connector may cause an electric shock or fire.
Do not set a glass of water, chemicals or any small metal objects
on the monitor.
zThismay cause damage,electric shock or fire.
zIf a foreign substance gets into the monitor, disconnect the plug
and then contact the Service Center.
Contact the Service Center or Customer Center for interior cleaning
once a year.
zKeep the product's interior clean. Dust which has accumulated in
the interior over an extended period of time may cause malfunction
or fire.

Notational
Power
Installation
Clean
Other
Do not remove cover(or back).
zThismay cause anelectric shock or fire.
zRefer servicing to qualified service personnel.
If your monitor does not operate normally - in particular, if there are
any unusual sounds or smells coming from it - unplug it
immediately and contact an authorized dealer or service.
zThis may cause an electric shock or fire.
Be careful not to let water drip into the monitor or expose the
monitor to moisture.
zThis may cause malfunction, an electric shock or fire.
zEspecially avoid operating the monitor near water or outdoors
where it could be exposed to snow or rain.
If the monitor is dropped or the casing is damaged, turn the
monitor off and unplug the power cord.
zThe monitor may malfunction, causinganelectric shock or fire.
zThen contact the Service Center.
Keep the power off when there is thunder and lightening outside, or
let the monitor remain unused for an extended period of time.
zThe monitor may malfunction, causinganelectric shock or fire.
Do not try to move the monitor by pulling only the wire orthe signal
cable.
zThis may cause a breakdown, electricshock or fire dueto
damage to the cable.
Do not move the monitor right or left by pulling only the wire or the
signal cable.
zThis may cause a breakdown, electricshock or fire dueto
damage to the cable.
Do not cover the vents on the monitor cabinet.
zBad ventilation may cause a breakdown or fire.

Do not use or store inflammable substances near the monitor.
zThis may cause an explosion or fire.
Never insert anything metallic into the monitor openings.
zThis may cause an electric shock, fire or injury.
Do not insert metal objects such as utensils, wire or drill bits, or
things that catch fire easily, such as pieces of paper or matches,
into the vents,the headphone orA/V ports on themonitor.
zThis may cause malfunction, an electric shock or fire.
zAlways contact the Service Center if foreign substances/objects
enter into the monitor.
If you view a fixed screen for an extended period of time, residual
image or blurriness may appear.
zChange the mode to energy save or set a screensaver to moving
picture when you need to be away from the monitor for an
extended period of time.
Be careful when adjusting the stand angle.
zApplying too much force may cause the monitor topple over or fall,
resulting in injury.
zYour hand or finger(s) may get caught between the monitor and the
stand, causing injury.
Adjust the resolution and frequency to the levels appropriate for
the model.
zInappropriate levels of resolution and frequency may damage your
eyesight.
19 inch - 1280 x 1024
Sitting too close to the monitor on a continuous basis may damage
eyesight.
To ease eye strain, take at least a five-minute break after every hour
of using the monitor.
Do not use the monitor where it can be exposed to strong
vibrations.
zExposure to strong vibrations may cause fire and shorten the life of
the monitor.

When moving the monitor, turn the power switch off and unplug the
power cord.
Make sure that all cables, including the antenna cable and cables
connected devices, are disconnected before moving the
monitor.
zFailure to disconnect cables may damage it and lead to fire oran
electric shock.

Unpacking
Front
Rear
Monitor and Stand
Please make sure the following items are included
with your monitor. If any items are missing,
contact your dealer.
Power Cord
DVI Cable
'DVI-A to D-SUB' Cable
Quick Setup Guide
Warranty Card
(Not available in all locations)
User's Guide and Monitor Drive
r
Natural Color software,
Pivot
®
Pro software