Samsung WMN-4270SD User manual

º~ ºº~ º

Components
Only use the supplied components for the bracket installation.
Product Image
Safety Instructions
Be sure to contact an authorized service center when installing your set.
Contact a qualified technician at your dealer for moving
or replacing the product after the installation. Do not hang on or give sudden impacts to the product.
1. Be sure to keep the product away from children. There can be serious damage on the head when hit by the edge of the product.
2. Be careful when you adjust the angle or rotate the set. The product can be damaged if it is too close to touch the wall.
(Attach some sponges to 4 corners of the product to avoid the product or wall damage.)
3. Do not install the product in a place with high temperature and high humidity. Avoid to install the product on the wall which cannot
bear the weight.
4. Under no circumstances insert your finger into the groove created by separating the stand at the bottom of the LED while installing
the LED onto the wall. There is a danger of electric shock.
5. Make sure to cover the groove with the cover supplied with the LED before completing the LED installation on the wall.
Angle Adjustment and Rotation Type Wall-Mount Bracket Installation Guide
WMN-4270SD
Angle Adjustment Bracket
1
Bracket
left : 1 right : 1
Screw : 4
Accessories
Anchor : 8 Screw : 8
Screw : 8
plastic hanger : 4
Wire Fixing Tool
: 1
Slim, Normal LED
Screw : 4
plastic hanger : 4
Ultra-Slim Only

Install the angle adjustment bracket on the wall as shown in the
figure.
Wall Bracket Assembly
Securely fix the set to the wall. Pull the bracket forward and unfold it. Insert
the bracket to the assigned area of the angle adjustment bracket and tighten
the supplied 8 screws . (Same for both left and right side)
Tighten the angle adjustment bracket by using anchors and screws
orderly from to .
If it cannot be installed on the assigned area, install at the nearest
place.
Remove the screws on the LED set. Put the plastic hanger and 4 screws together
and firmly tighten on the back panel.
W
Wa ar rn ni in ng g
1. Mount the product on the wall bracket. Be sure to check on the left and right side to see if it is properly fixed.
2. Be careful when installing the product or adjusting the angle as fingers can be caught in the holes.
3. Be sure the wall bracket is securely fixed to the wall. Falling down the product may cause physical dama
Make a hole in the wall with the drill of
6x50.
How to Tighten Anchors or Screws
Clean up the hole.
Insert the supplied anchor to the hole.
Match the angle adjustment bracket to
the holes on the wall and tighten the
screws .
Use the drill with the required size when making a hole in the wall.
Be sure to follow the directions for the installation to avoid safety
problems.
W
Wa ar rn ni in ng g
1. Check the solidity of the wall before the installation. Strengthen the wall and install the bracket if the wall is not firm enough.
2. The supplied screws and anchors are for installing on concrete walls.
3. For the wall of plaster, marble, or steel, use the appropriate screws.
Slim, Normal LED Ultra-Slim Only

Pull the wall bracket fixing part forward. Two people are required to install the product on the assigned area of the wall bracket.
For managing the power cord and other cables for peripheral equipments, bundle the wires
by using the supplied wire fixing tool. Be sure the wires are not unbundled or came off when
rotating or operating.
Insert the cables and pull the angle adjustment bracket forward. Arrange the wires by using
the hole to avoid the interference with wires when rotating the set.
Check the operation 2 ~ 3 times and fix the wall molding if it works properly.
Wall Bracket Angle Adjustment
The smooth moving mechanism is applied to this product to move the product smoothly for
convenience.
You can adjust the angle to left, and right side between 20º ~ -20º, to
down side to 10º ~ 15º.
The adjustable angle range may be vary depending on the model.
Do not adjust the angle with force. The product can be damaged if it is
too close to touch the wall.
Hold the left and right side of the product when you want to adjust the
left and right angle.
Hold the top center to adjust the down angle.
W
Wa ar rn ni in ng g
Install the LED set to the wall
bracket and rotate the 2 safety
pins on the upper part to fix.
Slim, Normal LED Ultra-Slim Only

Product Specifications
Product Standards
Width(mm) 465.0
Height(mm) 460.0
Depth(mm) 24.5
Weight(Kg) 5.5
Bracket VESA Standard 400 X 400
Information in this document is subject to change without notice.