Samsung SADT-103WM User manual

SADT - 103WM
Wall Mount Adaptor
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please
register your product at
www.samsung.com/global/register
SADT-103WM_ENG.indd 1 2008-03-18 오전 9:13:51

ENG
SADT-103WM_1
Overview
The Wall Mount Adapter is used to install the OUTDOOR
HOUSING (SHG-221/222) on the indoor/outside wall.
Notice
• Make sure that you must select an installation spot to endure the total weight of "Wall
Mount Adapter", "Outdoor Housing" and "Smart Dome Camera".
•This product is designed to use with anchor bolts and anchor nuts (M10).
• If installing in a concrete wall, use a M10 anchor bolt (nut) with flat washer and spring
washer.
•Each installed anchor bolt should endure 700kg of pulling force.
• Wall Mount Adapter can be installed directly in the wall, and also attached to CORNER
MOUNT ADAPTOR(SADT-110CM), or POLE MOUNT ADAPTOR(SADT-100PM). At this
time, please use the PG-13.5 cable grand.
Installation
1. Select an installation spot which can endure more than 4 times of the product weight.
2. Refer to the following wring diagram to prepare cables necessary for connecting the
Outdoor Housing.
SADT-103WM_ENG.indd 1 2008-03-18 오전 9:13:51

2_SADT-103WM
The wiring diagram to connect the outdoor cable of the OUTDOOR HOUSING(SHG-221/222)
3. If you mount the Wall Mount Adaptor on the wall, mark a hole where you insert the anchor
bolt or anchor nut (M10) using the Cover Plate, and drill a hole for the anchor bolt (nut).
If you install it in a corner of the wall, use the Corner Mount Adaptor (SADT-110CM).
If installing on the pole of the wall, use the Pole Mount Adaptor (SADT-100PM) for this
purpose.
COVER PLATE
The hole for joining
a ANCHOR BOLT
150 mm
80 mm
SADT-103WM_ENG.indd 2 2008-03-18 오전 9:13:52

ENG
SADT-103WM_3
4. Prepare the Holder Housing from the Outdoor Housing and insert the cables of the Holder
Housing into the Wall Mount Adaptor before pulling them out through the hole of the
Cover Fixing Part.
5. Fit the Guide of the Holder Housing into the corresponding Guide Hole of the Wall Mount
Adaptor while inserting the Holder Housing into the Wall Mount Adaptor.
- Install the Holder Housing so that the “FRONT” label faces the front of the camera.
- Make sure that the Bush Cable should not be loose from the Holder Housing.
(If the Bush Cable is not secured firmly, the product is not properly waterproof.)
HOLDER HOUSING
WALL MOUNT ADAPTOR
BUSH CABLE
GUIDE HOLE
GUIDE
WALL MOUNT ADAPTOR
CABLE
HOLDER HOUSING
The place for
joining a COVER
WALL MOUNT ADAPTOR
HOLDER HOUSING
SADT-103WM_ENG.indd 3 2008-03-18 오전 9:13:53

4_SADT-103WM
6. Turn the Holder Housing clockwise by 18 degrees. Then, use 3 screws(M4×L8,
suported), to fix the Holder Housing to the Wall Mount Adaptor.
7. According to the status of connected cable of the OUTDOOR HOUSING, SHG-221/222),
a way of installation is different as follows.
If the cable pipe is installed inside of the wall
Use the Cable Grand to connect the external cables with the Cover Plate.
- You should use only the Grand Cable for waterproof purpose. Furthermore, it is
recommended to keep the cable about 150mm longer than the Cover Plate.
COVER PLATE
150 mm
CABLE GRAND
WALL MOUNT ADAPTOR WALL MOUNT ADAPTOR
HOLDER
HOUSING
HOLDER HOUSING
SCREW
Turn to the clockwise
about 18 degrees
SADT-103WM_ENG.indd 4 2008-03-18 오전 9:13:54

ENG
SADT-103WM_5
If you use only the Grand Cable to fix the cables to the Cover Plate, the other hole of
the Cover Plate should be sealed up with the Rubber Cap for waterproofness.
The different cables on the Cover Plate can be pulled out through the hole of the Cover
Fixing Part of the Wall Mount Adaptor. 4) Then, use 6 screws (Flat, M3xL8) to fix the
Cover Plate to the Wall Mount Adaptor.
- Make sure that the Gasket part should keep contact with the Wall Mount Adaptor
during the fixation.
COVER PLATE
150 mm
CABLE GRAND
RUBBER CAP
WALL MOUNT ADAPTOR
The place for joining a COVER
GASKET COVER PLATE
SCREW
SADT-103WM_ENG.indd 5 2008-03-18 오전 9:13:55

6_SADT-103WM
If the cable pipe is installed outside of the wall
Drill a 21mm-diameter hole on the Wall Mount Adaptor (side and top, respectively).
For your reference, see the figure below.
- The drilling process for the Wall Mount Adaptor must be performed prior to the
fixing process of the Holder Housing according to the steps 4, 5, 6 in this installation
guide.
Put two Rubber Caps upon the Cover Plate.
- Make sure you do this as it is necessary for waterproofing.
COVER PLATE
RUBBER CAP




* Drilling Points (unit: mm)
(a) Top (b) Side
SADT-103WM_ENG.indd 6 2008-03-18 오전 9:13:56

ENG
SADT-103WM_7
Use the Grand Cable to fix the necessary cables to the Wall Mount Adaptor before
pulling them out of the hole of the Cover Fixing Part.
Use 6 screws (Flat, M3xL8) to fix the Cover Plate to the Wall Mount Adaptor.
- Make sure that the Gasket part should keep contact with the Wall Mount Adaptor
during the fixation.
8. Use the anchor bolt and nut to secure the Wall Mount Adaptor to the wall.
WALL MOUNT ADAPTOR
GASKET
COVER PLATE
SCREW
WALL MOUNT ADAPTOR
ANCHOR BOLT
WALL MOUNT ADAPTOR
CABLE GRAND
The place for
joining a COVER
SADT-103WM_ENG.indd 7 2008-03-18 오전 9:13:57

8_SADT-103WM
9. See the wiring diagram below for connecting the cables of the Camera Adaptor.
A. Remove one of the Connectors connected to the cable end of the Camera Adaptor.
B. Peel off the coating on the cable end of the Connector and connect it to the external
cable using soldering.
(See the cable wiring diagram in the installation guide of the Camera for connecting the
cables.)
C. Use an insulation tape to wrap up the soldering portion of two cables.
D. Connect the Connector to the Camera Adaptor again.
E. Repeat the above 4 steps to connect all of the 4 Connectors to the corresponding
external cables.
F. In the last step, connect the BNC jack.
CAMERA ADAPTOR CAMERA ADAPTOR
CABLE
CONNECTOR
BNC JACK
CONNECTOR
Soldering
External Cable
SADT-103WM_ENG.indd 8 2008-03-18 오전 9:13:59

ENG
SADT-103WM_9
10. Insert the joined cable into the Wall Mount Adaptor through the Cover Fixing Part.
Insert one piece of the two-strand cable into an empty area of the Wall Mount Adaptor
as in the figure below and push the other one into the Wall Mount Adaptor.
(Ensure that the insulated coating of the cable should be kept intact while the insertion)
11.Use 2 screws (M3xL4, suported) to fix the Cover to the Wall Mount Adaptor.
WALL MOUNT ADAPTOR
SCREW
COVER
WALL MOUNT ADAPTOR WALL MOUNT ADAPTOR
< Insert one piece of the two-stranded cable > < Insert the other piece of the two-stranded cable >
the place for joining a cover
SADT-103WM_ENG.indd 9 2008-03-18 오전 9:14:01