Samsung RS50N3513SA User manual

English
User servicing manual
1. You can check where to buy replacement parts at http://samsung.com/support
2. Visit the part purchase site and enter the model code of your product to check the parts
available for purchase. The model code is labelled on the outer side of your product.
- You can check the model code and version on the barcode label at the bottom left of
the product.
3. For replacement parts, make sure the part name matches that of the illustration in this
manual.
- User-serviceable parts are limited to handles (some models only), gaskets, drawers, and
hinges.
NOTE
Following the repair by a non-authorised service provider, self-repair or non-professional
repair of the product, Samsung is not liable for any damage to the product, any injury or
any other product safety issue caused by any attempt to repair the product which does
not carefully follow these repair and maintenance instructions. Any damage to the product
caused by an attempt to repair the product by any person other than a Samsung certified
service provider will not be covered by the warranty.
CAUTION
•The part name listed on the site may differ from that in this manual. Please make sure
you choose the right part name.
•Replacing hinges requires extreme caution because it involves detaching the door.
•Be sure to wear safety gloves while making repairs.
RB7300T_User-servicing-manual_EN.indd 1 10/15/2020 3:39:13 PM

English
The actual image and provided parts of the refrigerator may differ, depending on the model
and the country.
02 Drawer
04 Gasket
01Handle
03 Top hinge
05 Bottom hinge
RB7300T_User-servicing-manual_EN.indd 2 10/15/2020 3:39:14 PM
01
02
01
04
03
06

English
Handle replacement
Model name looks like this: RS54**3****, RS52**3****, RS50**3****,What replaces the
asterisks may differ depending the model.
Asterisk(s) in the model code indicate a variant model and may replace (0-9) or (A-Z) in
the model code.
CAUTION
•When replacing the door handle, take care not to scratch the front of the door.
•Firmly press the handles at the supports. Make sure there is no gap between the supports
and the door.
•Tightly fasten the screws when attaching the handle.
•Check that the handle is firmly attached before using the product.
Tools required (not provided)
Philips screwdriver Flat-head
screwdriver
To detach the handles
NOTE
This procedure applies to both the fridge and freezer compartment.
RB7300T_User-servicing-manual_EN.indd 3 10/15/2020 3:39:19 PM
1.Handle Assemblies are located on
the front of>the refrigerator door.
2.Insert the small flat-head driver to the
hole>at the bottom of Cap support
handle and>pull the handle assembly
out to the front>side with turning driver
to one side.
Turn around the Handle assembly
to>one side to dissemble about
the bottom>position

3.Unscrew 4 screws to diassemble
Cap support handle and Support
handle.
4.Pull the Support handle out using
hex wrench as shown or flat-head
driver pushing the back side.

English
Gasket replacement
CAUTION
Make sure you firmly attach the gasket. Otherwise, cold air from the refrigerator may leak.
To remove the gasket
1.Pull the 4 corners of gasket.
2.Pull the center of gasket.
To replace the gasket
1.Push the 4 corners of gasket.
2.Push the center of gasket.
RB7300T_User-servicing-manual_EN.indd 4 10/15/2020 3:39:20 PM
Pull the corne of Gasket
Pull the corne of Gasket
1. Push the 4 corners of gasket.
2. Push the center of gasket.

English
Hinge replacement
To replace the hinges, you must remove the doors first.
CAUTION
•When removing the doors, take extreme caution because the doors are heavy.
•Before replacing the hinges, put a soft pad such as cardboard on the floor to prevent
scratches on the door when you place the doors down.
•As the hinges must be handled carefully and replaced by two or more persons, we
recommend you to call for professional technical service.
•If you remove the hinge without holding the door, the door may fall and cause injury.
•Ensure that the shaft is firmly tightened on the hinge.
•Check that the hinge is firmly attached to the cabinet.
•Make sure the wire connectors are connected properly.
•Be careful not to damage the wires when fastening the top cover.
WARNING
•Tilting/laying the refrigerator requires a minimum of 2 people.
•Disconnect the power cord before reversing the doors.
Tools required (not provided)
Philips screwdriver Flat-head screwdriver 11 mm spanner
10 mm socket wrench 8 mm socket wrench 10 mm spanner
RB7300T_User-servicing-manual_EN.indd 5 10/15/2020 3:39:20 PM
Drawer replacement
CAUTION
Check that the drawer is inserted properly into the rail during assembly.
To remove the drawer
To reattach the drawers
Reattaching the drawers follows the reverse order of their respective removal steps.
1. Pull out the drawer as far as it goes.
2. Tilt the drawer up and pull it out until it
is removed.

English
Reversing the door
NOTE
For the models with handles, reverse the handles first. (For detailed information, see the
“Reversing the door handle position (For models with bar handles)” section.)
1. Disconnect the power cord, andremove 1 cover
screws using a Phillips screwdriver.
Then open the Freezer door and pull the hooks on
the sides to loosen the cover.
Lift up the cover towards you to detach it.
2.Disconnect the two top housings.
3.Remove the three bolts holding the hinge.
4.Disassemble the top hinge from
RB7300T_User-servicing-manual_EN.indd 6 10/15/2020 3:39:21 PM

English
RB7300T_User-servicing-manual_EN.indd 7 10/15/2020 3:39:21 PM
PPullullthe guide and hosethe guide and hose
PPushushthe guide and hosethe guide and hose
Hinge lHinge looww
Hinge lHinge looww
1. Disconnect the Power Cord.
2. Lay down the set.
Must working more than 2 people.
Be sure to unplug the power cord before
performing the operation above.
CAUTION
CAUTION
1. Disconnect Hose.
(Only Hinge Low Left)
2. Exhaust water in Hose.
(Only Hinge Low Left)
3. Remove Bolt(3ea).
(Using spanner or10mm Box wrench)
4. Remove Hinge Low R/L.
1. Assemble hinge low on bottom.
(Using spanner or10mm Box wrench)
2. connect Hose (Only Hinge Low Left)
3. Assemble water in Hose.
(Only Hinge Low Left)
CAUTION
Be sure to unplug the power cord
before performing the operation
above.
1. Assemble Hinge low R/L.
2. Put up the set.
CAUTION
Must working more than 2 people.
Hinge lHinge looww
Hinge lHinge looww