Samsung RS68N8941SL User manual

INSTALLATION MANUAL
SAMSUNG ELECTRONICS
ㆍLarger Capacity
ㆍClear view In-door ice system
ㆍSurround Multi Air Outlets
ㆍLED Lighting
RS68N8941**

Contents
How to install ------------ 15
3
Check the installation status 27
4
How to carry ------------ 10
2
Product Introduction ------- 3
1

To do list
3
1. Product Information
1-1. Basic Specifi cation
ITEM Specification
Model RS68N8941**
Image
Valid net
capacity
Gross capacity (LT) 628
Freezing compartment (LT) 234
Cold compartment (LT) 394
Dimensions (width x depth x height) W)912 x D)716 x H)1780
Dimensions of package (width x depth x height) W)960 x D)776 x H)1912
Rated frequency (Hz) 50 or 60
Rated voltage (V) 220~240 or 110~127
Rated power consumption of motor (W) 170
Rated power consumption ofheating device (W) 200 (AC 230V,120 V)
Refrigerator type Indirect Cooling Refrigerator
Refrigerant R-600a
Refrigerant charging volume 74g
Product weight (kg) 118
Weight of packaged product (kg) 122

To do list
4
ITEM Specification
Model RS68N8941**
Freezing Component
Compressor Type NF54M5151ARAK3
Drive mode INVERTER
Charged oil SUNUSO-2GSD(250cc)
Freezer Freezer
compartment SPLIT FIN TYPE
Cold compartment SPLIT FIN TYPE
Condenser Forced and spontaneous convection type
Desiccant Molecular sieve XH-9
Capillary tube Freezing
compartment F: ID0.75*L4000
Cold compartment R: ID0.85*L3500
Refrigerant R-600a
Components for defrosting
Freezer
Component
Section OFF
THERMISTOR
(F-SENSOR)
502AT
Strong (℃)-24
Intermediate (℃)-21
Weak (℃)-17
Cold
compartment
Section OFF
THERMISTOR
(R-SENSOR)
502AT
Strong (℃)0
Intermediate (℃)1.5
Weak (℃)5
1. Product Information
1-1-1. Electric Parts Specifi cation

To do list
5
ITEM Specification
Model RS68N8941**
Components for defrosting
Defrosting Cycle
Initial defrosting cycle
(simultaneous defrosting of F and R) 6 hours ±10 minutes
Defrosting cycle
of freezing component 12 to 77 hours
(varying dependent upon operation conditions)
Defrosting cycle of cold component 12 to 77 hours
(varying dependent upon operation conditions)
Idle duration -
Defrosting
Sensor
F defrosting
Sensor Type Thermistor (DTN-C502)
Specification 5.0 ㏀at 25℃
R defrosting
Sensor Type Thermistor (DTN-C502)
Specification 5.0 ㏀at 25℃
Bimetal (F) Type Bimetal thermostat (BT-121-M)
Operating
temperature (℃)On : 40℃, Off : 60℃
Bimetal (R) Type -
Operating
temperature (℃)-
1. Product Information
1-1-1. Electric Parts Specifi cation

To do list
6
ITEM Specification
Model RS68N8941**
Electric Component
Defrosting heater
in freezing
compartment
Power supplying
during freezing
compartment
defrosting
AC 230V,200W or AC120V,200W
Defrosting heater in
cold compartment
Power supplying
during cold
compartment
defrosting
-
Home bar heater
(cold compartment) Ambient humidity sensor interlocking -
Icemaker heater -
Dispenser heater AC 230V,6W or AC120V,6W
Water pipe heater DC12V,6W
Water tank heater -
Damper heater Kept tumed on -
Bimetal for preventing overheating of
defrosting heater in freezing compartment Thermostat (BT-121-M) On: 40℃, Off: 60℃
Bimetal for preventing overheating of
defrosting heater in cold compartment -
OLP
Type -
Operating
temperature (℃)-
Shutdown
temperature (℃)-
1. Product Information
1-1-2. Electric Component

To do list
7
ITEM Specification
Model RS68N8941**
Electric Component
Cooling fan motor in freezing compartment DC12V, AIO Q7
Cooling fan motor in cold compartment DC12V, AIO Q7
Compressor cooling fan motor DC12V, C150Q
Motor-driven damper
(True-taste chamber) -
Motor step valve DC 12V,700mA
DC valve -
Freezing compartment lamp DC12V, MAX 2.39W, 1EA
Cold compartment lamp DC12V, MAX 4.22W, 1EA
Fridge Door Lamp -
Door reed switch DC 200V 0.5A
Power cord AC 250V 10A or 16A
Grounding screw BSBN(BRASS SCREW)
1. Product Information
1-1-2. Electric Component

To do list
8
※Dispenser-featured models (RS68N8941**)
01 Freezer shelves 02 Multipurpose freezer bin 03
Dried food and meat storage drawer
04 Refrigerator bin 05 Refrigerator shelves 06 Vegetable drawer
07 Multipurpose drawer 08 Ice maker * 09 Water tank
10 Wine rack * 11 Dairy bin 12 Camera *
* Applicable models only
Note The design of the egg container may differ with the model.
08
01
02
03
11
04
07
06
09
05
12
1. Product Information
1-2. Interior Views

To do list
9
※RECESS HANDLE TYPE
1. Product Information
1-3. Dimensions (mm/inch)

NO ITEM PURPOSE SPEC QNT’Y CHECK PICTURES
1 LIFT GATE Loading/unloading Lift Hydraulic
Lifter 1 Everyday
2Dolly After unloading the unit from the truck, move the
unit on this dolly 460*750mm 1 Everyday
3 Fixing rope To fix the units while it’s moving on the way to
customers 25mm * 5 M 1 Everyday
4Wooden
protector When unloading, protect the units from damages 2 Everyday
2. How to carry
2-1. Equipments
To do list

NO SURROUNDING HOW TO CARRY PICTURES
1 plan ground
- carrying the unite by two persons
-using dolly, carry the unit in to the customer’s
house
- be careful not to be damaged
2 ladder car cannot access - check the path width - using a kind of protector, units should be moved
by two people
3 ladder car can access - check the path
- apply a proctor to the ladder not to damage the unit
4 elevator - check the path width - in case of narrow path, recommended to remove
the both doors
2. How to carry
2-1. Equipments
To do list

NO CAUSE DAMAGE PICTURES
1 Dropping damage - dropping shock owing to careless unloading
the delivery man didn’t use the lift gate
2 Dropping damage - dropping shock owing to careless unloading
the delivery man didn’t use the lift gate
3 Dropping damage - dropping shock owing to careless unloading
the delivery man didn’t use the lift gate
4 DENTS,SCRATCHES - scratched by narrow path or projecting stuff
2. How to carry
2-1. Equipments
To do list

NO PRECEDURES PRECAUTIONS PICTURES
1 LOADING - Recommend to use lift car - carrying the units by two persons
- be careful not to drop and got dents from the cargo
2ON THE WAY TO
CUSTOMER - tighten the unit by bend
- be careful not the band to damage the units
3 UNLOADING
- Recommend to use lift car
- carrying the units by two persons
- be careful not to drop and got dents from the cargo
2. How to carry
2-1. Equipments
To do list

SURROUNDINGS HOW TO OPEN PICTURES
Open place:no obstacles
Easy to lift up the carton box
- lift up the carton box
- fully recommended performed by two persons
- step removing the box can cause some scratches
on the edge of the refrigerator top
2. How to carry
2-1. Equipments
To do list

SALE
DELIVERY
INSTALLATION
DELIVERY
DATE
OPERATION
CHECK
COLLECTION OF
OLD PRODUCT COMPLETION
HOUSE
STRUCTURE
CHECK
INFORMATION OF
FUNCTION/USE
3. How to install
3-1. Installation process
To do list

3. How to install
3-2. Installation parts
To do list
Item. How to use Pictures
Phillips Head Driver Use for assembling and
disassembling of screw
Flat Head Driver Use for assembling and is assembling
of Beverage Station, Dispenser,
Display, Cover Lamp etc...
Magnet Use for checking of the
F/R Fan
Hexagon wrench
(4mm diameter) Use for adjust Door Hinge Ref Up
Box wrench (12 mm) Use for disassemble the compressor
Box wrench (10 mm) Use for disassemble the hinge lower
Spanner(19mm) Use for adjust the height of the door

NO HOW TO DO PICTURES
1
- Check if the floor is leveled.
If the floor is not leveled, it causes vibration and noise,
and when opening/closing the doors, the refrigerator
could be tipped over resulting in personal injuries.
2
- give enough gaps between the unit and the walls
- For dispenser models, select a place easy to access the
water supply with little humidity.
- Keep it away from places with direct sun light, much heat
or too low temp.
A place with a surrounding temp ranging from
41℉to 109.4℉is recommended.
A place with too high/low temps causes problem
and affects cooling power.
3. How to install
3-3. Selecting a good place
To do list

NO PRECEDURES HOW TO DO PICTURES
1Space Procurement - Secure enough space to remove the
packaging box.
2Removing packing box
Be careful not to scratch the product with
EPS or Angle and make sure to check the
outer appearance after removing all
packaging materials.
3
Remove the cap-top table
and Remove screws Remove the 3 screws holding down the Top
Table and remove the Top Table (1)
4Disassembling Connector Disconnect the electrical (2) above the upper left
door hinge To disconnect the connector (2) more
easily, press the end of the hook (3) and pull
connector.
3-4. How to dismantle the refrigerator doors
3. How to install To do list

19
Part name Work sequence Remarks
Door
1. Disconnect the power cord, and
Remove 3 cover screws using a
Phillips screwdriver.
Then open the refrigerator door and
pull the hooks on the sides to loosen
the cover.
Lift up the cover and towards you to
detach it.
2. Disassemble two connectors of the
housing.
3. Push the fixer hinge up, and pull it
forward to remove it.
4. Dissemble the top hinge from the front
the door.
3-5. Assembly Hinge-Up Disassembling (Cover Hinge Type –Freezer Door)
3. How to install

20
Part name Work sequence Remarks
Door
Remove the door from the lower hinge
by lifting up the door straight.
Be careful not to pinch the water
tubing and the wire harness on the
door.Lift up the door straight in
upper direction until the water hose
is eliminated from lower hinge.Do not
pull the door forward to remove it. It
cause injury of water hose and
tubing.
3-5. Assembly Hinge-Up Disassembling (Cover Hinge Type –Freezer Door)
3. How to install