Samsung SCO-6081R User manual

HD-SDI CAMERA
User Manual SCO-6081R

Copyright
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall
be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no
formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own
responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.
Warranty
If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve the
problem for free of charge. The warranty period is 3 years. However, the followings are excluded:
•If the system behaves abnormally because you run a program irrelevant to the system operation.
•Deteriorated performance or natural worn-out in process of time
Design and specifications are subject to change without prior notice.
HD-SDI Camera
User Manual
©2013 Samsung Techwin Co., Ltd. All rights reserved.

English _3
●overview
important Safety inStructionS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings, Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/ accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lighting storms or when unused for
long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
overview

overview
4_ overview
warninG
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC
OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS
ON THE EQUIPMENT.
Apparatus shall not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the apparatus.
caution
caution
riSK of eLectric SHocK.
Do not open
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
eXpLanation of GrapHicaL SymBoLS
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the product.

English _5
●OVERVIEW
Class construction
An apparatus with CLASS construction shall be connected to a MAINS
socket outlet with a protective earthing connection.
Disconnection Device
Disconnect the main plug from the apparatus, if it’s defected. And please call
a repair man in your location.
When used outside of the U.S., it may be used HAR code with fittings of
an approved agency is employed.
CAUTION
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so.
Please use the input power with just one camera and other devices must not
be connected.
The BNC Out terminal of the product is provided for easier installation, and is
not recommended for monitoring purposes.
If you keep the BNC cable connected, a risk of lightening may cause damage
or malfunction to the product.

overview
6_ overview
Please read the following recommend safety precautions carefully.
yDo not place this apparatus on an uneven surface.
yDo not install on a surface where it is exposed to direct sunlight, near
heating equipment or heavy cold area.
yDo not place this apparatus near conductive material.
yDo not attempt to service this apparatus yourself.
yDo not place a glass of water on the product.
yDo not install near any magnetic sources.
yDo not block any ventilation openings.
yDo not place heavy items on the product.
yDo not expose the camera to radioactivity.
User’s Manual is a guidance book for how to use the products.
The meaning of the symbols are shown below.
yReference : In case of providing information for helping of product’s usages
yNotice : If there’s any possibility to occur any damages for the goods and
human caused by not following the instruction
Please read this manual for the safety before using of goods and keep it in
the safe place.

English _7
●overview
contentS
oveRvIeW
3
3Important Safety Instructions
8Product Features
9What’s Included
10 At a Glance
InSTALLATIon &
ConneCTIon
13
13 Installation
16 Connecting with other Device
opeRATIng YouR CAmeRA 20 Menu Configuration
21 Menu Setup
AppenDIx
38 Specification
39 Product Overview
37 Troubleshooting
2
O
37

overview
8_ overview
PRODUCT FEATURES
•Supports Full HD-SDI Video
By adopting a diagonal 6mm (1/3”) 2M pixel CMOS, the camera produces clear picture
quality.
•Excellent low-illumination image quality
By adopting high-sensitive colour CMOS, the camera provides clear image quality under a
•SSNR3 (Samsung Super Noise Reduction) Function
The high-performance WN2 DSP chip effectively removes low-light gain noise and afterimage
to provide clear images even in dark environments.
•
This camera has a function that automatically selects the mode that is appropriate for
daytime or night-time conditions. The COLOR mode operates in daytime conditions to
provide optimum colors, and B/W mode operates in night-time conditions to enhance the
definition of the image.
•
•SSDR (Samsung Super Dynamic Range)
For images with high contrast between bright and dark areas from difficult lighting conditions
such as backlighting, this camera selectively illuminates darker areas while retaining the same
light level for brighter areas to even out the overall brightness.
•Miscellaneous Functions
HLC(High Light Compensation), SENS-UP, FLIP (H/V-REV), D-ZOOM and PRIVACY
functions are provided.
•OSD
By providing multi-lingual user-friendly OSD (On-screen Display) menu, the camera provides
easy handling of the camera.
Night (ICR)Day&
INTELLIGENCE
Once motion is detected, the camera sends an alert signal to the processing unit,
which, if used in conjunction with an optional alarm, can provide effective surveillance of
your property.
severe low illumination condition of 0.015 Lux (with SENS-UP, x60).

Appearance Item Name Quantity Description
1
1
1
1
3
1
1
●overview
wHat’S incLuDeD
Check if the main unit and all the following accessories are included in the product package.
English _9
Camera
Quick Manual
Cable for the testing monitor
L Wrench
Used to test the camera connection to a
portable display device
Used to remove and replace the dome cover
Tapping Screw
Used for installation on the wall or ceiling
Sunshield
Sunshield Hold
It protects the camera from the direct sunlight.
It fixes the sunshield with the camera.

a
b
c
c
d
TW
N F
/
/
@
d
overview
at a GLance
Appearance
10_ overview
Sunshield It protects the camera from the direct sunlight.
Sunshield Hold It fixes the sunshield with the camera.
SETUP Switch
The switch is used for setting and adjusting the camera’s functions andproperties.
Move this switch left or right to move the cursor or change
the value in the menu.
When menu is off, use this switch for adjusting focus.
Move this switch up or down to move the cursor in themenu.
When menu is off, use this switch for adjusting zoom.
Long to press this button to set the function in menu.
To move to a submenu item in the menu, press this switch.
Short to press this button to fit the focus automatically.
VIDEO
(for installation)
Analogue video output terminal of Video. Use a monitor cable for testing the
camera with a portable display.
Item Description
$
%
_ +
NF
T W
AF

a
b
d
c
CAUTION:Be ware of the
Rated Voltage and Polarity
of the power connection.
e
a
b
GREEN(485 –)
YELLOW(485+)
BLUE
(ALARM OUT)
GRAY(EXT_D/N IN)
BLACK(GND)
c
d
e
Components
Item Description
Power Port Used to plug the power cable.
I/O Port
Signal port for RS-485 communication.
Signal port for RS-485 communication.
Output port that signals when a motion is detected.
External signal input port for Day/Night mode setup.
Earth-grounding port for external signal.
HD-SDI Video Out
terminal BNC terminal for HD-SDI video signal output.
IR LED These infrared LED’s are controlled by the illumination sensor.
Illumination Sensor Detects incoming light to control the IR LED.
●overview
English _11

12_
CAUTION:Be ware of the
Rated Voltage and Polarity
of the power connection.
installation & connectioninstallation & connection
inStaLLation
J
This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the
external cable is not. You are recommended to install this product below the edge of eaves to
prevent the cable from being externally exposed.
Installation
1. Fix the camera in 3 holes by tightening the
three tapping screws supplied with the
product.
2. Connect the cables with the camera port.
3. Adjust the direction of the camera with the
L-wrench supplied with the product.
connectinG witH otHer Device
HD-SDI Monitor
Motion detection output device
Day/Night mode controller
Test monitor for
installation
installation & connection

Connecting to the monitor
Connect the video out port of the camera to the video input port of the monitor.
`To check the display screen after installing the camera for the first time, you can use the Video
port to check the video screen.
`You can set the video output type to either NTSC or PAL. (page 29).
`The Video source (4:3) will be displayed with either side truncated in comparison with the
HD-SDI video.
`The video source from the HD-SDI port can be displayed on the dedicated monitor. To display the
source on a commercial monitor, you need a converter to convert the video signal as appropriate.
Video Cable
The cable connecting the camera’s video output and a monitor is a BNC coaxial cable as
shown below.
If the distance between the camera and the monitor exceeds the recommended maximum,
please us an auxiliary video amp.
Maximum video transfer
distance
Recommended cable
specification
100~140m 5C2V(75ohm)
200m L-6CHD(75ohm)
(SDI-specific Cable)
J
●inStaLLation & connection
English _13
External Day/Night Switching Input
Day/Night mode of the camera can be switched by signal from an external device.
`To use this function, <DAY/NIGHT> setting of the camera should be set to the <EXTERN>.
(Page 27)
Motion Detection Signal Out
Upon a motion detection, the port outputs signal for an external device for display or operation.
When a motion is detected, the port outputs 3.3V signal.
`To use this function, <ALARM OUT> setting of the camera should be set to <ON>. (Page 31)
J
J

CAUTION:Be ware of the
Rated Voltage and Polarity
of the power connection.
DVR
PC
RS232C RS485, 422
CONVERTER
T+ T- R- R+
Power Supply
Use the screwdriver to connect each line (+, –) of the power cable to the corresponding
power port of the camera.
J`Be careful not to reverse the polarity when you connect the power cable.
`Be sure to turn the power off the device to be connected.
System Controller
or
RS-485
Converter
POWER
14_ installation & connection
For AC/DC Power Supply
You can use either one of AC 24V/1A~2A and DC 12V/2A~4A adaptor.
installation & connection

English _15
●inStaLLation & connection
Resistance of copper wire [at 20°C (68°F)]
Wire specification (AWG) #24(0.22mm
2
)#22(0.33mm
2
)#20(0.52mm
2
)#18(0.83mm
2
)
Resistance (Ω/m) 0.078 0.050 0.030 0.018
Voltage Drop (V/m) 0.028 0.018 0.011 0.006
Recommended Distance (m) Less than 20 Less than 30 Less than 30 Less than 30
•As shown in the table above, you may encounter a voltage-sag depending on the
wire length. If you use an excessively long wire for camera connection, the camera
may not work properly.
`Voltage for proper camera operation: DC 12V±10%, AC 24V±10%
`Voltage drop shown in the table above may show difference from the actual depending on the
manufacturer and cable type.
RS-485 Communications
Using RS-485 communication, the camera menu can be accessed using Samsung
Techwin’s System Controller or the DVR.
•For accessing the camera from a computer
Use a RS-485 converter to connect the camera’s control port with the computer’s
serial cable.
Ex) Serial port (COM1) of computer Serial Cable RS-485 Converter Camera’s
RS-485 control port
•For accessing the camera from a DVR or the System Controller
connect the camera’s RS-485+ and RS-485– terminals to the RS-485 control board’s
terminals of desired device with a RS-485 cable (TRX+ and TRX–).
Control ports of RS-485 Controller RS-485 ports of the camera
(+) CONNECTION TERMINAL (TRX+) 485+
(–) CONNECTION TERMINAL (TRX–) 485–
Default RS-485 communication settings
J
`When constructing a proprietary controller for direct camera control, apply Pelco-D or Samsung-
Techwin protocol.
`Use only a DVR model that supports HD-SDI saving.
Item CAM ID BAUD RATE UART MODE RET PKT
Default 19600 8-N-1 DISABLE

16_ Operating Your Camera
menu confiGuration
MAIN SETUP
LENS •DC
EXPOSURE
•BRIGHTNESS •SHUTTER •AGC
•SENS-UP
WHITE BAL
•ATW • •
• •
SIMPLE FOCUS •
BACKLIGHT •OFF •BLC •HLC
SSNR3 •ON •OFF
DAY/NIGHT
•AUTO •EXTERN •COLOR
•B/W
SPECIAL
•CAM TITLE •IMAGE ADJ •INTELLIGENCE
•PRIVACY •PROFILE •COMM ADJ
• •
EXIT
Operating Your Camera
•DEFOG •
OUTDOOR INDOOR
MANUAL AWC
➝
SET
SSDR
•RETURN
•
LANGUAGE RESET RETURN
•WDR
FOCUSING
➝
SET

menu Setup
To configure the camera’s function settings, use the button on the rear side of the product.
•$% Moves up/down in menu.
•_+
•Press the switch to set the function in camera menu.
To move to a sub-menu item in the menu, press this switch.
1. Press the SET button.
•Enters the function menu.
The selected function’s menu appears on the monitor.
2. Use the Up/Down buttons to select a desired function.
•Move the button up or down to move the arrow up or down.
Set the arrow to indicate the desired item.
2 : EXT_D/N 5 : RS-485-
3 : MD_OUT
Use up/down buttons
to set the desired item.
@
: Moves right/left in menu.
:
:
MAIN SETUP
1. LENS
2. EXPOSURE
3. WHITE BAL ATW
4. FOCUSING
5. BACKLIGHT OFF
6. SSNR3 ON
7. DAY/NIGHT AUTO
8. SPECIAL
9. EXIT
►
➝
SETSIMPLE FOCUS
Use right/left buttons
to change the
selection.
DC
Function Setup
switch
●opeRATIng YouR CAmeRA
English _17
$
%
_ +
NF
T W
AF

Operating Your Camera
18_ Operating Your Camera
3. Use the Up/Down buttons to select a desired function.
•Move the button right or left to display available values or settings.
Set the desired setting value using the button.
4. To finish, select <eXit> and press the SET button.
M
`
press the Function Setup switch.
`An item with the --- icon is unavailable due to function settings.
LenS
The lens type is fixedly DC.
An item with the icon also has sub menus. To select a sub menu, select an item with the icon
MAIN SETUP
1. LENS
2. EXPOSURE
3. WHITE BAL ATW
4.
5. BACKLIGHT OFF
6. SSNR3 ON
7. DAY/NIGHT AUTO
8. SPECIAL
9. EXIT
►
➝
SET
DC
SIMPLE FOCUS
FOCUSING
•Dc : Auto Iris Lens.
eXpoSure
1. When the SETUP menu screen is displayed,
select <eXpoSure> by using the Function
Setup switch so that the arrow indicates
<eXpoSure> .
2. Select a desired mode using the Function
Setup switch.
•BriGHtneSS : Adjust the screen brightness.
MAIN SETUP
1. LENS
2. EXPOSURE
3. WHITE BAL ATW
4.
5. BACKLIGHT OFF
6. SSNR3 ON
7. DAY/NIGHT AUTO
8. SPECIAL
9. EXIT
►
➝
SET
DC
SIMPLE FOCUS
FOCUSING

English _19
opeRATIng YouR CAmeRA●
•SHutter : You can select the shutter.
- –––:
- A.FLK : Select this when you experience
picture flicker, this happen when there is a
clash with the installed lighting frequency.
- ESC : Select this to control the shutter speed
automatically. If ESC is selected, the shutter
speed is automatically controlled depending on
the ambient illumination of the subject.
- MANUAL : You can control shutter speed manually (1/30sec ~ 1/16,000sec)
J
`When you use a DC lens, set the shutter mode to --- if color rolling occurs.
`Carefully position the camera when installing, since produced image quality might be poor if
framing a bright light source while the shutter mode of EXPOSURE is set to AUTO.
`When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.
EXPOSURE SETUP
1. BRIGHTNESS .... .... *.... .... 50
2. SHUTTER
3. AGC HIGH
4. SENS-UP AUTO
5.
RETURN
►
ESC
DEFOG ---
6. SSDR ON
7.
•SenS-up : When it is night or dark, the camera automatically detects the light level
and maintains a clear picture if this mode is activated.
- OFF : Deactivates the SENS-UP function.
- AUTO : Activates the SENS-UP function.
•aGc(auto Gain controL) : The higher the gain level, the brighter the screen -
but the greater the noise.
- OFF : Not being used
- Low : Allows automatic gain control from 5.3dB to 20dB.
- Medium : Allows automatic gain control from 5.3dB to 26dB.
- High : Allows automatic gain control from 5.3dB to 32dB.
•DefoG
- AUTO
- MANUAL
-
: Through the defogging function, camera can automatically recognize fog
concentration of the image, defog, self correct in hazy, rainy, flue gas and other
inclement weather to get a clear image.
OFF : Turn off Defogging function.
DEFOG SETUP
LEVEL MIDDLE
►
: The camera will automatically correct
image according to the defogging level
(low, middle, high) set by the user.
: The camera will adjust the definition
of the image according to user's
preferences through the defogging
level (low, middle, high).
RETURN
Shutter speed is fixed.

Operating Your Camera
20_ Operating Your Camera
•return : Select this to save the changes in the EXPOSURE menu and return to
the MAIN SETUP menu.
J
`Press the SET button while in AUTO mode to adjust the automatic scene accumulation multiplier
for low-illumination operation. (x2 ~ x60)
`The greater the video accumulation factor is, the brighter the screen is but the afterimage of a
moving object grows accordingly.
`Although noise, spots, and whitish symptoms may occur in higher accumulation, this is normal.
`If the gain control (AGC) of EXPOSURE mode is set to OFF, SENS-UP mode is accordingly set to
‘- - -‘.
•
- OFF
- ON
SSDR(Samsung Super Dynamic Range)
:: SSDR illuminates darker areas of an
image while retaining the same light level for brighter areas to even out the overall
brightness of images with high contrast between bright and dark areas.
to the contrast between bright and dark areas.
Use the Function Setup switch to change the SSDR level in the sub menu according
:
: Turn off SSDR function.
SSDR OFF
SSDR ON
wHite BaL (wHite BaLance)
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed,
select <wHite BaL>. by using the Function
Setup switch so that the arrow indicates
<wHite BaL>.
2. Select a desired mode using the Function
Setup switch.
MAIN SETUP
1. LENS
2. EXPOSURE
3. WHITE BAL ATW
4.
5. BACKLIGHT OFF
6. SSNR3 ON
7. DAY/NIGHT AUTO
8. SPECIAL
9. EXIT
►
➝
SET
DC
SIMPLE FOCUS
FOCUSING