Samsung SDZ-370 Series User manual

Thank you for purchasing a SAMSUNG CCD CAMERA.
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
High Resolution 37X Zoom Color Camera SDZ-370 User’s Manual
ENGLISH

Thank you for purchasing a SAMSUNG CCD CAMERA.
Before operating the camera, confirm the camera model and proper input
power voltage. In order to that you can understand this manual thoroughly,
we'll introduce our model description.
n SDZ-370 SERIES
 •NTSCMODEL •PALMODEL
  SDZ-370N  SDZ-370P
nMODEL DESCRIPTION
 •SDZ-370X
_
 •SIGNALSYSTEM
  N→NTSCMODEL
  P→PALMODEL
SIGNALSYSTEM
This installation should be made by a qualified service person and
should conform to all local codes.
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
WARNING - To prevent electric shock and risk of fire hazards:
◆ Do NOT use power sources other than that specified.
◆ Do NOT expose this appliance to rain or moisture.

COLOR CCD CAMERA User’s Manual
4
COLOR CCD CAMERA User’s Manual
5
Features
Contents
Fine Picture Quality under Ultra Low
Lighting
SSNR (Samsung Super Noise
Reduction)
ThehighperformanceW-IVDSPchip
dramatically reduces the gain noise in digital
image precessing, producing clear, sharp
images in low lighting environments.
1/4"highdensityCCDallowstheuserto
capturebright,high-qualityimagesunderultra
low lighting conditions.
Motion Detection
Oncemotionisdetected,thecamerasendsan
alert signal to the processing unit, which, if
used in conjunction with an optional alarm, can
provide effective surveillance of your property.
DIS(Digital Image Stabilizer)
TheDISfunctioncancompensateforvibrationof
the camera. so it helps you obtain more
stabilized image under the shaking conditions.
37x Optical Zoom
Thebuilt-inSDZ-370opticalzoomlensisa
highly durable component. It features auto
focus, auto iris, and zoom functions.
Miscellaneous Functions
SENS-UP,FLIP(H/V-REV),D-ZOOM,SHARPNESS,
MOTIONDETECTIONandPRIVACYfunctions
are provided.
Control via OSD Menu and RS-485
TheOSDmenuandRS-485pinsallowfor
remote control of the camera.
The user can also directly control the lens
using external control connection.
High Resolution
Featuring550TVlinehorizontalresolutionin
colormodeand680TVlinehorizontalresolutionin
BWmode,thecamerafeaturesSony's410,000
pixelCCDandcapturesclean,noiseless,high-
quality images.
Day & Night
The camera automatically determines whether
it is night time or day time, selecting operating
mode automatically. The camera operates in
color mode during day light conditions and BW
mode in night conditions for clearer identification.
• Features ………………………………………………………… 5
• Warnings & Cautions ………………………………………… 6
• Components and Accessories ……………………………… 8
• Overview………………………………………………………… 9
• Connection……………………………………………………… 11
nConnectingtoMonitor ……………………………………………… 11
nConnectingtoPower………………………………………………… 12
nConnectingto8PControlTerminal …………………………………… 12
• Operating Your Camera ……………………………………… 14
nMenuConfiguration ………………………………………………… 14
nMenuSetup ………………………………………………………… 14
-WHITEBALANCE ……………………………………………………… 15
-BACKLIGHT …………………………………………………………… 16
-MOTIONDETECTION …………………………………………………… 19
-FOCUS ………………………………………………………………… 20
-EXPOSURE …………………………………………………………… 25
-SPECIAL ……………………………………………………………… 29
-RESET ………………………………………………………………… 37
-EXIT …………………………………………………………………… 37
• Troubleshooting………………………………………………… 37
• Specifications ………………………………………………… 39
• STW Protocol Command Description ……………………… 40

COLOR CCD CAMERA User’s Manual
6
COLOR CCD CAMERA User’s Manual
7
SamsungTechwincaresfortheenvironmentatallproductmanufacturing
stages to preserve the environment, and is taking a number of steps to provide
customerswith more environment-friendly products.The Eco mark represents
SamsungTechwin'swilltocreateenvironment-friendlyproducts,andindicates
thattheproductsatisfiestheEURoHSDirective.
This information is provided to ensure your safety and to prevent any losses, financial or
otherwise.Pleasereaditcarefullyandusetheproductaccordingly.
*Forproductinquiries,pleasecontacttheretailshopwhereyouboughtthecamera.Theuseofequipmentsuchas
anaerialladderwhileprovidingafter-salesserviceshallbeatyourexpense.
*Separatethepowerplugwhenthundercrashesorlightingflashes.
* This product is support equipment for surveillance system. Therefore, we can't compensate for material loss and/or
personal injuries by robbery, fire, natural disaster or something like this type.
Ignoring this information may
result in material loss and/or
serious personal injuries including
death.
Indicates“NeverAllowed.”
Ignoring this information may
result in material loss and/or a
slight injuries.
Indicates“NoDisassembling.”
Warnings & Cautions
Warning/Attention/Special Mark Messages
Precautions
Do not install under extreme
temperature conditions.
Do not install in high humidity
environment.
Do not install under unstable
lighting conditions.
The lens is the most important component of
the camera. Be careful not to smear it with
fingerprints.
Severe lighting changes or flickering may hinder
normal camera operation.
May lower image quality.Use only under temperature conditions between
-10ºC and +50ºC. Provide good ventilation when
using in high temperature conditions.
Avoid touching the camera lens.
Do not drop the camera or subject
it to physical shock.
May damage the CCD.May cause a product malfunction.
Never keep the camera face to
strong light directly.

COLOR CCD CAMERA User’s Manual
8
COLOR CCD CAMERA User’s Manual
9
•Exposuretoaspotlightoranobjectemittingstronglightmaycausesmearorblooming.
•Ensurethatthepowersourcecomplieswithnormalspecificationsbeforesupplyingitto
the camera.
Notes
Precautions
Components and Accessories
Do not expose the camera to rain
or other types of liquids.
Radioactivity exposure may damage the CCD.May cause a product malfunction.Wipe dry any
liquids. Liquids may contain minerals that are
corrosive to electronic components.
Do not expose the camera to
radioactivity.
137x Zoom Color Camera SDZ-370
2Instruction Manual
38-PIN CABLE ASSY
1 2 3
Overview
1Tripod Mounting Bracket Screw Hole
Used to fix tripod mounting bracket on top of
the camera.
2
Tripod Mounting Hole
Used to install the camera on an optional tripod.
The tripod must be equipped with screws with
specifications shown on the right.
Top Bottom
1/4"-20UNC(20THREAD)
L:4.5mm±0.2mm(ISOstandard),
or0.197"(ASAstandard)
2
Attach the bracket to the top of the camera. Use screws included in
the package or their equivalent (less than 6mm). Otherwise, the
bracket may not assemble to the camera properly.
1

COLOR CCD CAMERA User’s Manual
10
COLOR CCD CAMERA User’s Manual
11
3
Key Buttons
Following buttons control zoom, focus, and auto focus functions.
WIDE button : To widen the view. (ZOOM OUT)
TELE button : To close in on a far object. (ZOOM IN)
F-NEAR button :To see a near object clearly.
F-FAR button : To see a far object clearly.
Pressing the 'SET' button locks the zoom control function of these buttons and
prompts the main setup menu.
Main setup menu can be navigated using these buttons.
SET : To access the main setup menu.
UP (TELE button) : To move the arrow indicator to up.
DOWN (WIDE button) : To move the arrow indicator to down.
LEFT (F-NEAR button) :To move the arrow indicator to left.
RIGHT (F-FAR button) : To move the arrow indicator to right.
Overview
4Power Input Terminal
Power supply terminal (DC12V±10%).
5
Power LED
Illuminates when power is supplied.
6
Video Output Jack
Used to connect an external video monitor in jack.
7
RJ-45 JACK
Terminals, such as RS-485 communications, MD OUT, ZOOM, and FOCUS, EX_DN
are areincluded.
Connection
Connecting to Monitor
Connect Video Out Jack to the monitor's Video In jack as shown below.
• Connection methods may vary depending on the video equipment. Please refer to
the model specific instruction manual.
• Connect cables with the unit powered down.
• Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate device.
CCD Camera Monitor
CCD Camera
Intermediate End monitor
Bottom View
3
4
6
5
7

COLOR CCD CAMERA User’s Manual
12
COLOR CCD CAMERA User’s Manual
13
•Connectthepoweroncetheinstallationiscomplete.
•Thewireispolarized.Match'+'and'-'terminalsproperly.
Notes
•MD(MotionDetection)OutputSignalLevel(lessthan10mA)
•WhenusingtheMDfunction,the'GND'shouldbeconnectedtotheframeground.
•Donot simultaneouslyconnectthe RS-485(+)(-) communicationline whenyouuse
voltagecontrolZOOMandFOCUS,usingtheRECEIVERBOX(SRX-100B).
Notes
Connection
The camera can be controlled by using external controllers like a Remote controller.
(RS-485 Communication)
SCC-3100A SCC-101 8-PinCABLEASSY
Connecto rFunction Signal Level I/O
ZOOM
Tele
I
Wide
FOCUS
Far
I
Near
COM -
MD O
EX DN
DAY mode: D&N terminals must be OPEN to external signals.
(Do not input voltage)
NIGHT mode: D&N terminal must be connected to the ground
I
There is motion
+3.0V
There is no motion
0V 5±0.5sec
← →
COM
-6V~-12V
COM
+6V~+12V
COM
-6V~-12V
COM
+6V~+12V
COM
*8PControlTerminalConfiguration
Connecting to 8P Control Terminal
Connecting to Power
DC Power Type (DC 12V, 500mA)
Use DC 12V/500mA power source for SDZ-370N/P.
PowerInputTerminal
Number Name Cable color Description Number Name Cable color Description
1ZOOM ORANGE
-
5GND BLUE -
2FOCUS WHITE/ORANGE 6EX DN WHITE/BLUE External D/N
3COM GREEN 7485+ BROWN RS-485 communication
4MD OUT WHITE/GREEN 8485- WHITE/BROWN RS-485 communication
* Match the communication setup between devices when you use the wired controller
(SCC-101) or SCC-3100A.
•Contactanauthorized
technician for
inspection.
Notes
ITEM SCC-101(fixed) SCC-3100A(Factory Default)
MODE Serial Serial
Data Bit 8 bit 8 bit
Bit/Sec 9600bps 9600bps
Parity EVEN NONE
CAM ID NO. 01~255
RETURN PACKET ENABLE See the SCC-3100A manual

COLOR CCD CAMERA User’s Manual
14
COLOR CCD CAMERA User’s Manual
15
Use the five buttons on back of the camera.
UPbutton
SET/AFbutton
LEFTbutton
DOWNbutton
RIGHTbutton
2. Select the desired feature using the UP or DOWN button.
• Each pressing of the UP or DOWN button moves the indicator to the next or
previous feature.
• Move the arrow indicator to the desired feature item.
3. Change the status of the selected feature using the LEFT or RIGHT button.
4. When completed, move the arrow indicator to 'EXIT' and press the SET button.
1. Press the SET button for 2 seconds. (Short-pressing the button activates
the AUTO FOCUS).
• Main setup menu is displayed on the monitor screen.
MAIN SETUP
WHITE BAL ATW
BACKLIGHT OFF
MOTION DET OFF
FOCUS
EXPOSURE
SPECIAL
RESET
EXIT
MAIN SETUP
WHITE BAL ATW
BACKLIGHT OFF
Operating Your Camera
Menu Configuration
Menu Setup
SelectfeatureusingtheUPor
DOWNbutton. Changethestatususingthe
LEFTorRIGHTbutton.
White Balance (White Bal.)
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed, select ’White Bal.‘ by using the Up
and Down buttons so that the arrow indicates ’White Bal.‘ .
2. Select a desired mode using the Up and Down buttons.
•Featuresmarkedwitha have an accessible submenu.
•AccessthesubmenubypressingtheSETbutton.
Notes
Main Setup Menu
WHITE BAL • ATW • MANUAL • AWC->SET
• OUTDOOR • INDOOR
BACKLIGHT • OFF • BLC • HLC
MOTION DET • OFF • ON
FOCUS
• MODE • ZOOM TRK • ZOOM SPEED
• D-ZOOM • ZOOM POS INIT • USER PRESET
• LENS INIT • END
EXPOSURE
• BRIGHTNESS • IRIS • SHUTTER
• AGC • SSNR • SENS-UP
• END
SPECIAL
• PRIVACY • DAY/NIGHT • DIS
• COMM ADJ • IMAGE ADJ • DISPLAY
• END
RESET
EXIT

COLOR CCD CAMERA User’s Manual
16
COLOR CCD CAMERA User’s Manual
17
✽Select one of the following 5 modes, as appropriate for your purpose.
ATW : Select this when the color temperature is between 1800ºK and
10500ºK
INDOOR : Select this when the color temperature is between 4500 ºK and 8500 ºK .
OUTDOOR : Select this when the color temperature is between 1800ºK and
10500ºK. (sodium light inclusion)
AWC →SET : To find the optimal setting for the current luminance environment in this
mode, set the point the camera towards a sheet of white paper and press the
SET button. If the environment changes, readjust it.
MANUAL : Select this to fine-tune White Balance manually. Set White Balance first by
using the ATW or AWC mode. After that switch to MANUAL mode, fine-
tune the White Balance and then press the SET button.
•WhiteBalancemaynotworkproperlyunderthefollowingconditions.Inthiscaseselect
theAWCmode.
1When the color temperature of environment surrounding the subject is out of the control
range
2When the ambient illumination of the subject is dim.
3If the camera is directed towards a fluorescent light or is installed in a place where
illumination changes dramatically, the White Balance operation may become unstable.
Notes
2. Select a desired mode using the Left and Right buttons depending on the camera pupose.
BACKLIGHT
This camera is designed so that it delivers a distinctive subject and background at
The same time, even when the subject is in backlight, unlike conventional cameras,
By adopting a proprietary W-IV DSP chip.
1. When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using the Up
and Down buttons so that the arrow indicates ‘BACKLIGHT’.
BLC : Enables a user to directly select a desired area from a picture, and to view the
area more clearly.
HLC(High Light Compensation) : If there is a high light installed in dark environment
such as an apartment parking garage or gas
station entrance, removing the high light makes
it possible to view car license plates efficiently.
Operating Your Camera
MAIN SETUP
WHITE BAL ATW
BACKLIGHT OFF
MOTION DET OFF
HLCMASKINGAREA
HLCON HLCOFF
WHITE BAL MANUAL SETUP
RED 117
BLUE 93
▶END
||||||||||||||||||||||||||
||||||||||||||||||||||||||
Press SET to Return

COLOR CCD CAMERA User’s Manual
18
COLOR CCD CAMERA User’s Manual
19
Operating Your Camera
•YoucannotusetheBLCmodewhenMANUALorA.FLKmodein‘SHUTTER’menuis
selected.
•SincethefollowingsymptomsmayoccuraccordingtotheambientilluminationwhenBLC
isselected,setittoOFF.
1Colororscreenchangesunnaturally.
2Noiseappearsinthebrightpartofthescreen.
•SincetheperformanceoftheBLCfunctionmaybeaffectedbytheareaofthebrightpart
ofthescreen,optimizetheinstallationangleforthebestBLCperformance.
•IfyouincreaseLIMIT,thescreendisplaymaybedistorted.
•For highperformanceofBLCfunction,Werecommendthat yousetIRIStoAUTOinthe
EXPOSUREsetup.
•ActivatingBLC maycause thecameratorepeattheAutoFocusoperationdependingon
lightingconditions.ItisrecommendedthatyouusetheFocusSetup menu in One-Push or
Manualmode.
•SmartZoomandBLCcannotbeusedinconjunctionwitheachother:
•SettingupBLCandthenSmartZoomautomaticallycancelsBLC.
•SettingupSmartZoomandthenBLCautomaticallycancelsSmartZoom.
Notes
This product has a feature that allows you to observe movements of objects in 4
different areas on the screen, and the words ‘MOTION DETECTED’ appear on the
screen when movement is detected; hence a single individual can conduct
supervision efficiently. The camera detects an object’s movement by sensing
disparity of outline, and level of brightness and color. The camera receives detection
signal from MD output terminal.
• Please press the SETUP button.
- OFF: MOTION DETECTION mode is cancelled.
- ON: Any motion in the selected areas is observed.
AREA SEL : You can select the area you wish to observe from the 8 area.
AREA MODE : Determines whether to use the MD area selected in SENSITIVITY
SENSITIVITY : You can select up to 8 MD areas.When SENSITIVITY number is
high, motion detection sensitivity is increased to recognize even
small movement
SMART ZOOM : Smart zoom is operated in connection with MOTION DETECTION.
When the SMART ZOOM function is ‘ON’ while the MOTION
DETECTION mode is ‘ON’, the zoom goes to the TARGET ZOOM
position once motion is detected. Once the zoom action is finished
and ‘DWELL TIME’ has passed, the zoom returns to the ‘START
Motion Detection
MD SETUP
▶AREA SEL AREA1
AREA MODE ON
SENSITIVITY LOW
SMART ZOOM ON
END
AREA SETUP
▶TOP 3
BOTTOM 6
LEFT 3
RIGHT 6
END
||||||||||||||||||||||||||
||||||||||||||||||||||||||
||||||||||||||||||||||||||
||||||||||||||||||||||||||
SMART ZOOM SETUP
▶START ZOOM X1
TARGET ZOOM X5
DWELL TIME 5 SEC
END
HLC SETUP
▶LEVEL LOW
MASK COLOR 5
END
||||||||||||||||||||||||||
• Select ‘HLC’ to adjust the HLC MASK COLOR and
LEVEL.
OFF : Deactivates the BACKLIGHT function.
3. Select a desired mode using the Left and Right
button and press the SET button.
• Select ‘BLC’ to adjust the area to be enhanced and
enhancement level.
BLC SETUP
▶LEVEL LOW
TOP 30
BOTTOM 70
LEFT 30
RIGHT 70
END
||||||||||||||||||||||||||
||||||||||||||||||||||||||
||||||||||||||||||||||||||
||||||||||||||||||||||||||

COLOR CCD CAMERA User’s Manual
20
COLOR CCD CAMERA User’s Manual
21
Operating Your Camera
Tips on Using the Motion Detection Feature
•Thefeaturemaynotfunctionproperlyunderflickeringlightconditions.
•Thecamerainterpretssuddenchangesinlightingandsubsequentchangeinbrightnessof
an object as motion.
•Withthefeatureenabled,otheralgorithmsmayrequireadditionaltimetooperatethan
usual.
Notes
FOCUS
1.Press the SET button to access the main setup manu and then position the
indicator over FOCUS using the UP or DOWN button.
2. Press the SET button.
MODE : You can select the most suitable zoom mode. Move the arrow indicator to
’MODE‘ using UP or DOWN button.
MAIN SETUP
WHITE BAL ATW
BACKLIGHT OFF
MOTION DET OFF
FOCUS
EXPOSURE
• AUTO : Select AUTO and press the SET button to
confirm. Increase or decrease optical zoom
(ZOOM) or digital zoom (D-ZOOM)
positions using the UP or DOWN button
while verifying the changes on screen.
Enabling D-ZOOM (ON) means that digital
zoom will activate once optical zoom
ends. Focus is automatically adjusted with
moving zoom.
• ONE PUSH : Focus is automatically adjusted just once,
after zoom position is changed. Select
'ONE PUSH' and press the SET button to
confirm. Increase or decrease optical zoom
(ZOOM) or digital zoom (D-ZOOM)
positions using the directional buttons
while verifying the changes on screen.
Press the SET button once desired image quality is obtained.
ZOOM POS SETUP
↑: TELE ↓: WIDE
ZOOM/FOCUS POS SETUP
↑: TELE ↓: WIDE
←: NEAR →: FAR
FOCUS SETUP
MODE ONE-PUSH
ZOOM TRK AUTO TRACK
ZOOM SPEED FAST
D-ZOOM OFF
ZOOM POS INIT AUTO
USER PRESET OFF
LENS INIT MANUAL
END
•Thissystemdoesnotguaranteepreventionoffireortheft.The
manufacturer shall not be held responsible for any accident or
damage incurred.
•ConnectanexternalalarmdevicetoMDOutonbackofthe
camera.
Notes
ZOOM’ position.
• START ZOOM : Use the left or right button in the ‘START ZOOM’ item to select the zoom position
from 1x to 37x to be returned after the ‘SMART ZOOM’ action is over.
• TARGET ZOOM : Use the left or right button in the ‘TARGET ZOOM’ item to select the zoom
position from 1x to 37x to be used during MOTION DETECTION.
• DWELL TIME : Use the left or right button in the ‘DWELL TIME’ item to select a time between
5 and 60 seconds for the dwell time before the zoom is returned to the ‘START
ZOOM’ position. (5,7,10,15,20,30,40,60 sec)
TOP, BOTTOM, LEFT,RIGHT : You can adjust the size of the area

COLOR CCD CAMERA User’s Manual
22
COLOR CCD CAMERA User’s Manual
23
ZOOM SPEED : Configure zoom tracing speed using this feature. Position the indicator
over 'ZOOM SPEED' using the UP or DOWN button and then set to
desired mode using the LEFT or RIGHT button.
Operating Your Camera
FOCUS SETUP
MODE
ONE-PUSH
ZOOM TRK AUTO TRACK
FOCUS SETUP
MODE
ONE-PUSH
ZOOM TRK AUTO TRACK
ZOOM SPEED FAST
FOCUS SETUP
MODE ONE-PUSH
ZOOM TRK AUTO TRACK
ZOOM SPEED FAST
D-ZOOM OFF
ZOOM POS INIT AUTO
• FAST : To move zoom fast.
• MEDIUM : To move zoom at medium speed.
• SLOW : To move zoom slowly.
D-ZOOM : Configure magnification limit from x2~x12 using this feature. Position the
indicator over 'D-ZOOM' using the UP or DOWN button. Set 'D-ZOOM' to
'ON' and press the SET button to confirm.
•The 'ZOOMSPEED'modecannotbe used if 'MODE'issetto'AUTO'and'ZOOMTRK' is
'ON'.
Notes
- Set 'ZOOM LIMIT' to the desired level using the
LEFT or RIGHT button.
ZOOM POS INIT: Moves to the controlled ZOOM position when the power truned
on and is a function of the initial ZOOM position control.
D-ZOOM LIMIT SETUP
▶LIMIT X2
END
FOCUS SETUP
MODE ONE-PUSH
ZOOM TRK AUTO TRACK
ZOOM SPEED FAST
D-ZOOM OFF
ZOOM POS INIT AUTO
USER PRESET OFF
Use the left or right button in the ‘ZOOM’ item to select ‘AUTOTRACK’ or ‘TRACK’ and press
SET button to activate the zoom action focus function.
• AUTOTRACK: Zooming in while deciding or adjusting the status of the focus.
• TRACK: Zooming in with no relevance to the focus.
• OFF: Only the zoom lens moves.
•WhentheDISisenabled,youcannotusetheD-ZOOM.
Notes
• MANUAL : Sel ect 'MANUAL' and press the SET button
to confirm. Increase or decrease optical
zoom (ZOOM) or digital zoom (D-ZOOM)
positions using the directi onal buttons
while verifying the changes on screen. Press
the SET button on ce desired image quality
is obtained. Focus can be manually
adjusted, independent of moving zoom.
ZOOM TRK : Select ‘ON’ for the ‘SMART ZOOM’ item in the MOTION DETECTION menu
and press SET button to change the settings for the ‘SMART ZOOM’ function.
ZOOM/FOCUS POS SETUP
↑: TELE ↓: WIDE
←: NEAR →: FAR

COLOR CCD CAMERA User’s Manual
24
COLOR CCD CAMERA User’s Manual
25
- PRESET NO : Up to 128 preset configuratons are
supported.
- PRESET SAVE : Save configured preset.
- PRESET CLEAR : Clear configured preset.
- END : Revert to the FOCUS SETUP menu.
END : To revert to the main setup menu.
LENS INIT : Use the left or right button in the ‘Lens
initialization’ item to select
‘Automatic’ or ‘Manual’ and press the
SET button to set up the initialization
of the lens.
Operating Your Camera
FOCUS SETUP
MODE ONE-PUSH
ZOOM TRK AUTO TRACK
ZOOM SPEED FAST
D-ZOOM OFF
ZOOM POS INIT AUTO
USER PRESET OFF
LENS INIT MANUAL
END
LENS INIT SETUP
DAY
1
END
EXPOSURE
MAIN SETUP
WHITE BAL ATW
BACKLIGHT OFF
MOTION DET OFF
FOCUS
EXPOSURE
SPECIAL
USER PRESET SETUP
▶ PRESET NO 1
PRESET SAVE
PRESET CLEAR
END
PRESET NOT DEFINED
||||||||||||||||||||||||||
USER PRESET SETUP
PRESET NO 1
▶ PRESET SAVE
PRESET CLEAR
END
PRESET NOT DEFINED
||||||||||||||||||||||||||
USER PRESET SETUP
PRESET NO 1
PRESET SAVE
▶ PRESET CLEAR
END
PRESET NOT DEFINED
||||||||||||||||||||||||||
FOCUS SETUP
MODE ONE-PUSH
ZOOM TRK AUTO TRACK
ZOOM SPEED FAST
D-ZOOM OFF
ZOOM POS INIT AUTO
USER PRESET OFF
LENS INIT MANUAL
END
• AUTO :The lens is initialized by setting the date. reset time can be set from 1 day to
7 days and the lens resets every 24 hours from the set time.
• Manual :The Lens will reset when you press the SET button.
ZOOM/FOCUS POS SETUP
↑: TELE ↓: WIDE
←: NEAR →: FAR
- AUTO :If you turn the power off and on, the zoom magnification level is set to the
previous level that was set before the power went off.
- MANUAL : The zoom magnification level can be set from 1x to 37x.
•Thezoompostionissavedafter5secondswhenyousetzoomfunction.
Notes
USER PRESET
• Prese t user-designated configurations using this feature. Position the indicator over
‘USER PRESET’ using the UP or DOWN button and then set to ‘ON’ using the LEFT
or RIGHT button. Press the SET button to confirm.

COLOR CCD CAMERA User’s Manual
26
COLOR CCD CAMERA User’s Manual
27
IRIS: Set 'IRIS' to 'AUTO' or 'MANUAL'. Position the indicator over 'IRIS' using the UP
or DOWN button and then select the desired iris mode using the LEFT or RIGHT
button.
• AUTO: The iris is automatically activated upon illumination.
• MANUAL: Man ual iris configuration. Set 'IRIS' to 'MANUAL' using the LEFT or RIGHT
button and then press the SET button. Increase or decrease iris level using
the LEFT or RIGHT button while verifying the changes on screen.
SHUTTER : Control image brightness by adjusting shutter speed.
1
Position the indicator over 'SHUTTER' using the UP or DOWN button. Then select
the desired shutter mode (A.FLK, ESC, MANUAL) using the LEFT or RIGHT button.
2
If you choose ’MANUAL‘, select the optimal
shutter speed.
• In MANUAL mode, the optimal shutter speed
needs to be designated. Select from 1/60 to
1/120,000 (NTSC) or from 1/50 to 1/120,000
(PAL). * 'Sens-Up' mode can be configured
manually (2x to 256x).
• Verify changes made to the shutter speed by
referencing to changes in on screen brightness.
• A.FLK (NTSC: 1/100, PAL: 1/120): Flicker-free mode
• ESC : Automatic shutter speed setting (optimal).
Auto operation is possible only when the IRIS is set to MANUAL.
• MANUAL: Manual shutter speed setting
IRIS MANUAL SETUP
▶IRIS VAL F1.6
END
Operating Your Camera
EXPOSURE SETUP
BRIGHTNESS 50
IRIS AUTO
SHUTTER ESC
||||||||||||
|
|||||||||||||
EXPOSURE SETUP
BRIGHTNESS 50
IRIS AUTO
SHUTTER ESC
AGC MEDIUM
||||||||||||
|
|||||||||||||
•Imagemaybecomeunstableifthecameraissetto'ESC'modeandfacesastrong
fluorescent light.
•Under'ESC'mode,thebrightnesscanbeadjustedusingtheLEFTorRIGHTbutton.
Notes
3
Press the SET button to complete.
SHUTTER MANUAL SETUP
▶SHUTTER VAL 1/60
END
EXPOSURE SETUP
BRIGHTNESS 50
IRIS AUTO
||||||||||||
|
|||||||||||||
1. Press the SET button to access the main setup menu and then position the
indicator over 'EXPOSURE' using the UP or DOWN button.
2. Press the SET button to confirm.
BRIGHTNESS:
Use this feature to adjust image brightness. Position the indicator over
'BRIGHTNESS' using the UP or DOWN button.Then increase or decrease brightness
level using the LEFT or RIGHT button while verifying the changes on screen. Set
END once desired level is obtained.

COLOR CCD CAMERA User’s Manual
28
COLOR CCD CAMERA User’s Manual
29
SSNR(Samsung Super Noise Reduction): On screen noise reduction.
1Position the indicator over 'SSNR' using the UP or DOWN button.
2Set 'SSNR' to the desired mode using the LEFT or RIGHT button.
• LOW : Low noise reduction
• MEDIUM : Medium noise reduction
• HIGH : High noise reduction
• OFF : Disabled
•Changing'AGC'settingfromLOWtoHIGHresultsingreatersensitivity,aswellason
screen noise.
•Setting'AGC'toOFFlocks'SSNR'configuration.
Notes
SENS-UP : This feature ensures clear images at night or under low lighting
conditions.
1Position the indicator over 'SENS-UP' using the UP or DOWN button.
2Set 'SENS-UP' to the desired mode using the LEFT or RIGHT button.
• AUTO : Select this mode for use in night time or under low lighting conditions.
• OFF : Disabled
•Once'AUTO'modeisset,theusercanconfigureSens-Uplimitbyincreasing/decreasing
theshutterspeed(e.g.:X2,X4.......X32,X64,X128,X256).
•EnablingSens-Upincreasescamerasensitivityandmayresultinadditionalnoiseand/or
other phenomenons. This is normal.
Notes
Operating Your Camera
EXPOSURE SETUP
BRIGHTNESS 50
IRIS AUTO
SHUTTER ESC
AGC MEDIUM
SSNR MEDIUM
SENS-UP OFF
||||||||||||
|
|||||||||||||
EXPOSURE SETUP
BRIGHTNESS 50
IRIS AUTO
SHUTTER ESC
AGC MEDIUM
SSNR MEDIUM
SENS-UP OFF
||||||||||||
|
|||||||||||||
GAIN MANUAL SETUP
▶LEVEL 5dB
END
EXPOSURE SETUP
BRIGHTNESS 50
IRIS AUTO
SHUTTER ESC
AGC MEDIUM
SSNR MEDIUM
||||||||||||
|
|||||||||||||
AGC (Auto Gain Control) : For brighter images.
1Position the indicator over 'AGC' using the UP or DOWN button.
2Set 'AGC' to the desired mode using the LEFT or RIGHT button.
• HIGH : Wide range gain value adjustment
• MEDIUM : MEDIUM range gain value adjustment
• LOW : Narrow range gain value adjustment
• MANUAL : Selecting gain value range. (5dB ~ 41dB)
• OFF : Disabled

COLOR CCD CAMERA User’s Manual
30
COLOR CCD CAMERA User’s Manual
31
2Set up the mode using the 4 direction buttons.
• AREA SEL : You can select up to 8 MD areas.
• AREA MODE : Determines whether to use the
area selected in the AREA SEL, and
the size and position of the area.
• MASK COLOR : Determine area color. You can select
Gray, Green, Red, Blue, Black,White.
AREA SETUP
▶TOP 45
BOTTOM 110
LEFT 20
RIGHT 20
END 70
||||||||||||||||||||||||||
|||||||||||||||||||||||||
||||||||||||||||||||||||||
||||||||||||||||||||||||||
||||||||||||||||||||||||||
1When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the Up and
Down buttons so that the arrow indicates 'DAY/NIGHT'.
2Select a desired mode using the Left and Right buttons according to the picture
display you want.
• COLOR : The picture is always displayed in color.
• B/W : The picture is always displayed in black and white.
• AUTO : The mode is switched to 'Color' in a normal environment, but
switches to 'B/W' mode when ambient illumination is low.To set up
the sswitching time or speed for AUTO mode, press the SET button.
• MASK TONE : Determine the transparency of selected area as controlling number from
0 to 3.
• END : Select this to save the PRIVACY menu settings and return to the
SPECIAL menu.
DAY/NIGHT : You can display pictures in color or black and white.
Operating Your Camera
SPECIAL SETUP
PRIVACY OFF
DAY/NIGHT AUTO
DIS OFF
COMM ADJ
• EXT : This mode allows you to apply a desired filter to external signals.
Color →B/W B/W →Color
Fast 2.5 lux 4 lux
Slow 0.8 lux 6 lux
1When the SPECIAL menu screen is displayed, press
the Up and Down buttons so that the arrow
indicates ‘PRIVACY’.
PRIVACY SETUP
▶AREA SEL AREA1
AREA MODE ON
MASK COLOR GRAY
MASK TONE 0
END
||||||||||||||||||||||||||
- DWELL TIME :You can select the duration time
about changing the day/night mode.
→5,7,10,15,20,30,40, 60(sec)
- DURATION : You can select brightness of
illumination about changing the
day/night mode.
DAY/NIGHT AUTO SETUP
▶DWELL TIME 5 SEC
DURATION FAST
END
SPECIAL
MAIN SETUP
WHITE BAL ATW
BACKLIGHT OFF
MOTION DET OFF
FOCUS
EXPOSURE
SPECIAL
RESET
1.Press the SET button to access the main setup menu and then position the
indicator over 'SPECIAL' using the UP or DOWN button.
2. Press the SET button to confirm.
PRIVACY : Hide an area you want to hide on the screen.
SPECIAL SETUP
PRIVACY OFF
DAY/NIGHT AUTO
DIS OFF

COLOR CCD CAMERA User’s Manual
32
COLOR CCD CAMERA User’s Manual
33
(between 0 and 255).
• Protocol : Select the communication PROTOCOL. (STW/PELCO-D/PELCO-P/
BOSCH/HONEYWELL/VICON/AD/SEC/PANASONIC)
• BAUD RATE : You can select 2400/4800/9600/19200/38400/57600/115200 bps.
• UART MODE : You can select NONE, EVEN or ODD for the parity bits.
• TERMINATION : Functi on that sets the resistance at the end of RS-485
communications.
1
When the SPECIAL menu screen is displayed, press
the Up and Down buttons so that the arrow indicates ‘COMM ADJ’.
2Set up the mode using the 4 direction buttons.
• CAM ID : Determines the camera's identification number
COMM ADJ (Communication Adjustment) :
This function sets up the camera communication
status when controlling the camera through an
external control device.
COMMUNICATION SETUP
▶PROTOCOL STW
CAM ID 1
BAUD RATE 9600
UART MODE 8-N-1
TERMINATON OFF
RET PKT DISABLE
END
||||||||||||||||||||||||||
Operating Your Camera
•WhenDISisoperating,D-ZOOMdoesnotoperate.
Notes
✽Setting Termination Resistance.
In order to prevent signal reduction, the termination resistance of the 2 end units,
which are the distant paths for camera and controller to be connected on the RS485
interface, should be connected.
As the termination resistance is built in the camera, whether to make the termination
resistance valid or invalid is selected with the TERMINATION.
See the connection diagram for determining to which device the termination
resistance will be connected to.
Set up the termination resistance in the dark products.
The installation distance of the product for the termination resistance setting should
be less than 1.2 Km. (Maximum cable length is 1.2 Km according to the RS-485
standards.)
DIS : The DIS mode can compensate for vibration of the camera.
•Whenusing aVideoAutoIrisLens,ifyousetthe lensleveltolow,automatic switching
betweenColorandBlack&Whitemaynotoccur.
• YoucannotcontroltheDAY/NIGHTmenuwhenAGCintheEXPOSUREmenuis‘OFF’.
Atthistime,theexchangebetweenDAYmodeandNIGHTmodeoperatesaslikeselecting
‘COLOR’mode.
•The OSD key does not work for 3 seconds when switching to Color or B/W, to ensure
stable camera operation.
• The camera may focus less well under infrared illumination than under normal illumination.
•Since thecameramay notfocusas wellunderinfraredilluminationatnight asitdoes
undernormalillumination,installanExtra-lowDispersionLenstoobtainsharppictures.
•Thebrightnessofilluminationischangeablebyinstalledenvironment.
Notes
SPECIAL SETUP
PRIVACY OFF
DAY/NIGHT COLOR
DIS OFF
COMM ADJ

COLOR CCD CAMERA User’s Manual
34
COLOR CCD CAMERA User’s Manual
35
Operating Your Camera
SPECIAL SETUP
PRIVACY OFF
DAY/NIGHT COLOR
DIS OFF
SYNC INT
COMM ADJ
IMAGE ADJ
DISPLAY
END
1When the SETUP menu screen is displayed, select ‘IMAGE ADJ.’ by using the Up and
Down buttons so that the arrow indicates 'IMAGE ADJ.
2Select a desired mode using the Up and Down buttons.
• H-REV : You can flip the picture horizontally
on the screen.
• V-REV : You can flip the picture vertically on
the screen.
• SHARPNESS : As you increase this value, the picture
outline becomes stronger and clearer.
•COLOR : Adjusting this value affects the chroma level only; the burst level
is unaffected.
•END : evert back to the USER PRESET menu.
DISPLAY : Use this feature to designate a name for the camera, which will display
on the monitor screen
IMAGE SETUP
▶H-REV OFF
V-REV OFF
SHARPNESS ON
COLOR 50
END
||||||||||||||||||||||||
SHARPNESS SETUP
▶LEVEL 16
END
||||||||||||||||||||||||
CAM TITLE
1Press the SET button to display the main setup menu and move the arrow indicator
to ‘CAM TITLE’ using the UP or DOWN button.
2Set ‘CAM TITLE’ to ‘ON’ using the LEFT or RIGHT button.
•IftheCAMTITLEfeatureissetto‘OFF’,
the name will not displayed in the monitor
Notes
DISPLAY SETUP
▶CAM TITLE OFF
CAM ID ON
CAM INFO ON
MD ALARM -----
ZOOM MAG ON
LANGUAGE ENGLISH
END
• RET PKT : You can choose whether to send an ACK signal when the
communication control command is issued to the camera.
SPECIAL SETUP
PRIVACY OFF
DAY/NIGHT COLOR
DIS OFF
SYNC INT
COMM ADJ
IMAGE ADJ
DISPLAY
IMAGE ADJ : Includes image quality or special function factors.
•IfCameraiscontrolledbytheViconController,functionbuttonmaynotworkproperly.
Notes

COLOR CCD CAMERA User’s Manual
36
COLOR CCD CAMERA User’s Manual
37
Operating Your Camera
4You can enter up to 20 characters.
a. Move the cursor to the character entry field using the LEFT or RIGHT button.
b. Use UP, DOWN, LEFT and RIGHT buttons to select a desired character.
c. Press the SET button to confirm selection of the blinking character. The character
is then saved, and the cursor in the entry field moves to the next position.
d. Repeat steps a through c until the desired name has been entered.
• Correcting Mistakes
Movethecursorth‘CLR’andpresstheSETbuttontocleartheentireentry.Tomodifyone
character,useLEFTorRIGHTtopositionthecursorabovethecharactertobemodifiedand
clicktheSETbuttonafterselectingthecharactertoenter.
Notes
5Enter a title, move the cursor to ‘POS’ and press
the SET button. The entered title appears on the
screen. Select the position to display the title on the
screen by using the 4 direction butons and press
the SET button.
When the position is determined, select.
• CAM ID : Displays camera ID on top left corner of the screen.
• CAM INFO : Displays camera information on screen.
• MOTION ALARM : You can toggle the use of the camera alarm.
• ZOOM MAG : Use th is feature to display the current zoom magnification level
on screen. Position the indicator over ‘ZOOM MAG’ using the
UP or Down button. Then set to ON using the LEFT or RIGHT
button.
• LANGUAGE : You ca n select the menu language according to your
requirements (Korean, ESPANOL, FRANCAIS, ITALIANO,
DEUTSCH, ENGLISH, Japanese, Chinese)
• END : Select this to save the SPECIAL menu settings and return to the
SPECIAL menu.
FRONT DOOR
To reset your camera to factory default condition.
To finish setup menu.
RESET
EXIT
Troubleshooting
If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an authorized
technician.
• Nothing appears on the screen.
- Check that the power cord and line connection between the camera and monitor are
fixed properly.
- Check that you have properly connected VIDEO cable to the camera VIDEO output jack.
• The image on the screen is dim.
- Is lens stained with dirt? Clean your lens with soft, clean cloth.
- Set the monitor to proper condition.
- If the camera is exposed to too strong light, change the camera position.
3Press SET button.
CAMERA TITLE SETUP
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
0123456789 ( )
< >-/#¬S!?,.
←→ CLR POS END

COLOR CCD CAMERA User’s Manual
38
COLOR CCD CAMERA User’s Manual
39
• The image on the screen is dark.
- Adjust the contrast feature of the monitor.
- If you have an intermediate device, set the 75Ω / Hi-z properly.
• The camera is not working properly, and the surface of the camera is hot.
- Check that you have properly connected the camera to an appropriate power source.
• The DAY/NIGHT menu does not work.
- Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
• The SENS-UP function does not work.
- Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
- Check that SHUTTER of EXPOSURE SETUP menu is ‘A.FLK’ or ‘MANUAL’.
• The Motion Detection function does not work.
- Check that MOTION DEF of SPECIAL SETUP menu is ‘OFF’.
• Color is not correct.
- Check the setting of WHITE BAL SETUP menu .
• The screen flickers continually.
- Check that direction of camera turns toward the Sun.
• RS-485 communication fails.
- Check the polarity between RS-485 Control Port and RS-485 cable.
- Check the RS-485 Communication establishment initial value
- We recommend that you make ground connect between camera and controller in order to
maintain safety communication control.
Troubleshooting
* RS-485 Communication establishment initial value
Specifications
485 Control Board Connection Port RS-485 Control Port
(+) CONNECTION TERMINAL (TRX+) 485+
( - ) CONNECTION TERMINAL (TRX-) 485-
Item Camera ID BAUD RATE UART MODE RET PKT
Initial value 19600 8-NONE-1 DISABLE
SDZ-370N SDZ-370P Note
POWER
Input Voltage DC 10.8V ~ 13.2V (Recommended : 12V )
Power Consumption 2.8 W : Steady-state (at 12V)
5.1 W : Max. (Zoom, Focus, Day&night motor operating, at 12V)
CCD
Size 1/4 Inch, Super HAD color CCD
Total Pixels 811(H) x 508(V) 795(H) x 596(V)
Effective Pixels 768(H) x 494(V) 752(H) x 582(V)
O
P
T
I
C
S
Optics 37X, f=3.5 to 129.5mm(F1.6 to 3.9)
Min. Focus Distance 1500mm
D. ZOOM OFF/ON (Limit 12x)
Angle Field of view H : Appr. 55.5˚(Wide) to 1.59˚(Tele) V : Appr. 42.5˚(Wide) to 1.19˚(Tele)
Sync.
Scanning System 2:1 Interlace
Synchronization Internal
Frequency H: 15.734KHz / V: 59.94Hz H: 15.625KHz / V: 50.00Hz
E
L
E
C
T
R
I
C
A
L
Resolution 550 TV Lines(Min.) : Color / 680 TV Lines(Min.) : B/W
Min. Illumination 0.4 Lux/F1.6(50IRE): Color/0.02 Lux/F1.6(50IRE): B/W
S/N (Y signal) 50 dB (AGC OFF,Weight ON)
Video Output CVBS (1.0Vp-p/75Ω)
Focus AUTO/MANUAL/ONE-PUSH
Zoom Movement Speed 2.5 Sec Wide to Tele
IRIS Control AUTO/MANUAL
Lens Initialize Built-In
Camera Title ON/OFF 20 characters
Camera ID 256EA
ID:000 ->
Remote only
Day & Night AUTO/COLOR/BW/EXT IR-Cut Filter
Gain Control LOW/MEDIUM/HIGH/MANUAL/OFF Removable
White Balance ATW/AWC/MANUAL/INDOOR/OUTDOOR
BACK LIGHT BLC/HLC/OFF
Shutter Speed AUTO/MANUAL/A.FLK 1/120,000sec~X256
O.S.D KOREAN,ESPANOL,FRANCAIS,ITALIANO,DEUTSCH,ENGLISH,JAPANESE,
CHINESE : total 8 language
Motion Detection ON/OFF
Control Output RS-485 (2400/4800/9600/19200/38400/57600/115200bps)
SSNR LOW/MEDIUM/HIGH/OFF
Privacy Function ON/OFF (8 Zones)
FLIP ON/OFF
MIRROR ON/OFF
DIS ON/OFF
PRESET 128 Positions
PROTOCOL STW, PELCO-D, PELCO-P, SEC, PANASONIC, VICON,AD, HONEYWELL, BOSCH
Operating Temperature/Humidity -10˚C to +50˚C / 20% to 80% RH
Storge Temperature/Humidity -20˚C to +60˚C / 20% to 95% RH
Dimension 67.6(W)X67.6(H)X124.7(D) mm
Weight 450g