Samsung SID-50 User manual

This installation should be made by a qualified service person and should conform to all local codes.
The lightning flash with arrowhead symbol, within an equilateral triangle is intended
to alert the user to the presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
INFORMATION-This equipment has been tested and found to comply with limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will required to correct the interference at his own expense.
WARNING - Changes or modifications not expressly approved by the manufacturer could
void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use other than specified power source.
Do NOT expose this appliance to rain or moisture.
PRECAUTIONS GETTING TO KNOW YOUR CAMERA
FEATURES
Do not install the camera in extreme
temperature conditions.
Only use the camera under conditions where
temperatures are between -10˚C and +50˚C.
Be especially careful to provide ventilation
when operating under high temperatures.
Do not install or use the camera in an
environment where the humidity is high.
It can cause the image quality to be poor.
Do not touch the front glass of the
camera.
It is one of the most important parts of camera.
Be careful not to be stained by fingerprint.
Never keep the camera face to strong
light directly.
It can damage the CCD.
Do not drop the camera or subject
them to physical shocks.
It can cause malfunctions to occur.
Do not expose the camera to rain or
spill beverage on it.
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that corrode the
electronic components.
Never use the camera close to a gas
or oil leak.
It can cause malfunctions to occur.
Do not install the camera under
unstable lighting conditions.
Do not disassemble the camera.
There are no user-serviceable parts inside it.
Severe lighting change or flicker can cause
the camera to work improperly.
• If the camera is exposed to spotlight or object reflecting the strong light, smear or blooming may occur.
• Please check the power whether it satisfies the normal specification before connecting the camera.
Notes
Horizontal Resolution 540 TV Lines
Clear image quility has been achieved by employing a CCD with 410,000 pixels(NTSC), 470,000
pixels(PAL) and optimized WINNER3 DSP CHIP which provides a horizontal resolution of 540 TV lines.
High Sensitivity
The built-in high sensitivity COLOR CCD enables a clear image even in 0.3Lux (Sens-up) or lower illumination.
SSNR (Samsung Super Noise Reduction)
By using built-in SSNR function manufactured by SAMSUNG TECHWIN, the amount of low illuminance
noise has been significantly reduced, and the signal-to-noise ratio (S/N) as well as horizontal resolution
have been improved, resulting in a clear and sharp image display even in the dark.
Pan and Tilt
Pan and tilt are available after installing camera.
MINI DOME CAMERA USER’S MANUAL
7
MINI DOME CAMERA USER’S MANUAL
6
MINI DOME CAMERA USER’S MANUAL
2
MINI DOME CAMERA USER’S MANUAL
3
MINI DOME CAMERA USER’S MANUAL
5
MINI DOME CAMERA USER’S MANUAL
4
SID-50
HIGH RESOLUTION MINI DOME CAMERA
INSTRUCTION MANUAL
About this manual
Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.
Thank you for purchasing a SAMSUNG CCD CAMERA.
Before operating the camera, confirm the camera model and proper input power voltage. In
order that you can understand this manual thoroughly, we'll introduce our model description.
SID-45C SERIES
• NTSC models • PAL models
SID-50N SID-50P
Model Description
• SID-50X • SIGNAL SYSTEM
N NTSC Model
P PAL Model
Signal system
WARNING
The camera needs periodic inspection.
Contact an authorized technician for inspection.
Stop using your camera when you find a malfunction.
If you use your camera around smoke or unusual heat for a long time, a fire
may be caused.
Do not Install the camera on a surface that can not support it.
Unless the surface is suitable, it could cause falling or other hazards.
Do not handle the camera with wet hands
It could cause an electric shock.
Do not disassemble the camera.
It may result in fire, electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in fire or other hazards.
Pan Base
You can rotate the lens
from 360˚
Tilt Base
You can adjust up and
down the camera(20°~90°).
Front
Power Input Terminal
Label for Jack Type
BNC Jack
Bottom
P/No. : Z6806-0715-01B
VAN 08. 10
www.samsungtechwin.com
www.samsungcctv.com
•SAMSUNG TECHWIN CO.,LTD.
145-3, Sangdaewon-dong, Jungwon-gu, Seongnam-si,
Gyeonggi-do, 462-120, Korea
TEL : [phone]~8 FAX : [phone]
•SAMSUNG OPTO-ELECTRONICS UK,LTD.
Samsung House, 1000 Hillswood Drive, Hillswood
Business Park Chertsey Surrey KT16 OPS
TEL : [phone] FAX : [phone]
•SAMSUNG TECHWIN AMERICA,LTD.
1480 Charles Willard St. Carson, CA 90746, UNITED
STATES
TEL : [phone] FAX : [phone]
•TIANJIN SAMSUNG OPTO-ELECTRONICS CO.,LTD.
No.9 ZHANGHENG STREET. MICRO-ELECTRONIC INDUSTRIAL
PARK JINGANG-ROAD TIANJIN, CHINA 300385
TEL : [phone] FAX : [phone]
SALES NETWORK

Connection to Monitor
•
As a connecting method varies according to instruments, refer to the manual supplied with
the instrument.
•Connect the cable after power is turned off.
•Set the 75Ω/ Hi-Z selection switch. If it is a intermediate device, switch it to Hi-z and if
it is final device, switch it to 75Ω. (Please refer to the Monitor Manual.)
DOME Camera
MonitorIntermediate
BNC
Connection to Power
•
Connect the adapter to the power input connector as shown in the figure below. Use a
DC 12V. (The Adapter is not provided with the Dome Camera.)
DOME Camera
Adapter (not provided)
Power Input Connector
DIMENTION SPECIFICATION DECLARATION OF CONFORMITY
• When installing the camera on a ceiling or a wall, not to disturb adjustment of Tilt Base angle fix
the BNC-Power Cable on the Pan Base clip.
Notes
• After loosening Pan or Tilt Base holding screws, adjust its angle. And then tighten screws again.
• In case of adjusting the tilting, do not take the lens for preventing hysical shocks. Please take the Tilt Base.
• This dome camera is to be installed on the ceiling by factory default. In case of using camera on the wall,
readjust the Tilt angle as page 8 (Notes).
Notes
Panning & Tilting Control
You can adjust the Panning and Tilting angle freely. (Panning angle: 360°,
Tilting angle: 20°~90°)
1)
Adjustment Panning angle: After attaching the dome camera to a ceiling or a wall, adjust the
panning angle for better monitoring area by rotating the Pan Base. The panning angle can be
adjusted 360° freely.
2) Adjustment Tilting angle: After attaching the dome camera to a ceiling or a wall, adjust
the tilting angle for better monitoring area by rotating the Tilt Base. The tilting angle can
be adjusted to 20° from 90° freely. (based the ceiling surface)
Resistance of copper wire [at 20C˚ (68˚F)]
• As the voltage drop according to the length of the cable in the above table, a camera may
malfunction if there is an excessively long cable run.
* Voltage for camera operation: 12V DC ±10%
* Voltage drops in the above table are variable according to types of cable manufacturer.
For DC Power Type
Copper wire size (AWG) #24(0.22mm
2
) #22(0.33mm
2
) #20(0.52mm
2
) #18(0.83mm
2
)
Resistance ( Ω/ m) 0.078 0.050 0.030 0.018
Voltage Drop (V/m) 0.028 0.018 0.011 0.006
Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.
MINI DOME CAMERA USER’S MANUAL
11
MINI DOME CAMERA USER’S MANUAL
10
MINI DOME CAMERA USER’S MANUAL
14
MINI DOME CAMERA USER’S MANUAL
13
<Installing the camera on a ceiling> <Installing the camera on a wall>
MINI DOME CAMERA USER’S MANUAL
9
MINI DOME CAMERA USER’S MANUAL
12
INSTALLATION
Accessories
Installing Camera
User Manual Quick Install Guide Cable Rubber Template
M4 Taping Screw 2EA
1. Fix the camera to a ceiling or a wall using two screws.
2. After fixing it, adjust its pan base and
tilt base properly.
3. After adjusting them, secure the shield
case and dome-cover.
Built-in functions of the SID-50 Camera include the following
MINI DOME CAMERA USER’S MANUAL
8
CAMERA OPERATION
Screw
Shield Case
Dome Cover
Hole
BNC-Power Cable
Pan Base
You can rotate the lens
from 360˚
Tilt Base Holding
Screws
Tilt Base
You can adjust up and down
the camera (20°~90°).
Pan Base Holding Screw
Auto Functions
Electronic Shutter
Speed
WHITE BALANCE
BACKLIGHT
GAIN CONTROL
SSNR
(Noise Reduction)
SENS UP
SHARPNESS
Setting
Value
ESC
ATW
OFF
MIDDLE
LOW
X12
8
Descriptions
The speed is controlled according to the
brightness of the screen.
It can be used within the color temperature
range 1,800K~10,500K(Ex fluorescent light,
outdoor, sodium vapor lamp or inside tunnels)
The gain increases within the range of
6dB~34dB
The gain increases or decreases within the
range of 6dB~34dB
There is sufficient reduction in noise levels
without causing much ghost imaging
It helps maintain a bright, clear screen image by
automatically detecting changes in the level in
low light levels without causing much ghost
imaging.
The outline of the video image becomes cleaner
and more distinctive as the level of
SHARPNESS increases.
99.2
2-Ø 4.2
63.5
99.2
99.2
R 41.2
67
Application of Council Directive(s) 89 / 336 / EEC
Manufacturer's Name SAMSUNG TECHWIN CO., LTD
Manufacturer's Address SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-120
European Representative Name
European Representative Address
Equipment Type/Environment MINI DOME CAMERA
Model Name SID-50
Beginning Serial NO. S6300001
Year of Manufacture 2006. 03. 01
Conformance to EN 50081-1 : 1992
EMC-Directive 89/336 EEC and 92/31/EEC
EN 50130-4 : 1996
We, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s).
Manufacturer SAMSUNG TECHWIN CO., LTD
Legal Representative in Europe
Signature Signature
Full Name HAN SEUG KIM Full Name
Position QUALITY CONTROL MANAGER Position
Place CHANGWON, KOREA Place
Date 2006. 03. 01 Date
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the
end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please
separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details
of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not
be mixed with other commercial wastes for disposal.
SID-50N SID-50P
ITEM
Power Source
Total Pixels
Effective Pixels
SIZE
Scanning System
Synchronization
Frequency
LENS(Built-in)
Resolution
Video Output
S/N(Y signal)
Min.Illumination
Auto Functions
BACKLIGHT
Auto Functions
Monitoring Pan
Angle Tilt
Operating temperature/Humidity
Dimention
Weight
DC 12V±10%/Max. 1.8W
811(H) x 508(V) 795(H) x 596(V)
768(H) x 494(V) 752(H) x 582(V)
1/3 inch Super HAD CCD
2:1 Interlace
Internal Only
Horizontal:15.734 KHz/Vertical :59.94 Hz Horizontal: 15.625 KHz/Vertical : 50Hz
Built-in Fixed Lens 120 f=3.0mm, F2.0
540 TV Lines(Min.)
CVBS : 1.0Vp-p/75
50 dB (AGC Off,Weight ON)
0.3 Lux/F1.2, 0.002 Lux/F1.2(Sens-upX128)
Electronic shutter speed AUTO
LOW / MIDDLE / HIGH / OFF
WHITE BALANCE AUTO
Gain Control AUTO
SENS-UP AUTO
SSNR(Noise Control) AUTO
SHARPNESS AUTO
Manual 360
Manual 20 ~ 90
-10˚C to +50˚C / 30% to 80% RH
Ø100 x 70mm(H)
200g
CCD
Sync.
E
L
E
C
T
R
I
C
A
L
It needs control KEY to change OSD menu, please contact our customer service if you
need to control OSD menu.