Samsung SWA-9200S User manual

English
User Manual
VA81-01146Q-00
NSPBI01285A-00
SWA-9200S
© 2022 Samsung Electronics Co., Ltd. All rights reserved.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care Centre.
SAFETY INFORMATION
Thank you for purchasing this
product (SWA-9200S).
CAUTION
RISK OF ELECTRIC SHOCK. DO NOT
OPEN.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER (OR BACK). NO USER-
SERVICEABLE PARTS ARE INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL. Refer to the table
below for an explanation of symbols which may be on
your Samsung product.
This symbol indicates that high voltage is
present inside. It is dangerous to make any
kind of contact with any internal part of this
product.
This symbol indicates that this product has
included important literature concerning
operation and maintenance.
Class II product : This symbol indicates that
it does not require a safety connection to
electrical earth (ground).
If this symbol is not present on a product
with a power cord, the product MUST have
a reliable connection to protective earth
(ground).
AC voltage : This symbol indicates that the
rated voltage marked with the symbol is AC
voltage.
DC voltage : This symbol indicates that the
rated voltage marked with the symbol is DC
voltage.
Caution, Consult instructions for use : This
symbol instructs the user to consult the user
manual for further safety related information.
• The slots and openings in the cabinet and in the back or
bottom are provided fornecessary ventilation. To ensure
reliable operation of this apparatus, and to protect it
from overheating, these slots and openings must never
be blocked or covered.
‒ Donotplacethisapparatusinaconnedspace,
such as a bookcase, or built-in cabinet, unless proper
ventilation is provided.
‒ Do not place this apparatus near or over a radiator
or heat register, or where it is exposed to direct
sunlight.
‒ Do not place vessels (vases etc.) containing water
onthisapparatus.Awaterspillcancauseareor
electric shock.
• Do not expose this apparatus to rain or place it near
water (near a bathtub, washbowl, kitchen sink, or
laundry tub, in a wet basement, or near a swimming
pool, etc.). If this apparatus accidentally gets wet,
unplug it and contact an authorized dealer immediately.
• Do not overload wall outlets, extension cords or
adaptors beyond their capacity, since this can result in
reorelectricshock.
• Route power-supply cords so that they are not likely to
be walked on or pinched by items placed on or against
them. Pay particular attention to cords at the plug end,
at wall outlets, and the point where they exit from the
apparatus.
• To protect this apparatus from a lightning storm, or
when it is left unattended and unused for long periods
of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage
to the set due to lightning and power line surges.
• Before connecting the AC power cord to the DC adaptor
outlet, make sure the voltage designation of the DC
adaptor corresponds to the local electrical supply.
• Never insert anything metallic into the open parts of
this apparatus. Doing so may create a danger of electric
shock.
• To avoid electric shock, never touch the inside of this
apparatus.Onlyaqualiedtechnicianshouldopenthis
apparatus.
• Makesuretoplugthepowercordinuntilitisrmly
seated. When unplugging the power cord from a wall
outlet, always pull on the power cord’s plug. Never
unplug by pulling on the power cord. Do not touch the
power cord with wet hands.
• If this apparatus does not operate normally - in
particular, if there are any unusual sounds or smells
coming from it - unplug it immediately and contact an
authorized dealer or service centre.
• Maintenance of Cabinet.
‒ Before connecting other components to this product,
be sure to turn them off.
• Be sure to pull the power plug out of the outlet if the
product is to remain unused or if you are leaving the
house for an extended period of time (especially when
children, elderly, or disabled people will be left alone in
the house).
‒ Accumulated dust can cause an electric shock, an
electricleakage,orarebycausingthepowercord
to generate sparks and heat or the insulation to
deteriorate.
• Contact an authorized service centre for information
if you intend to install your product in a location with
heavy dust, high or low temperatures, high humidity,
chemical substances, orwhere it will operate 24 hours
a day such as in an airport, a train station, etc. Failing to
do so may cause serious damage to your product.
• Use only a properly grounded plug and wall outlet.
‒ An improper ground may cause electric shock or
equipment damage. (Class l Equipment only.)
• To turn this apparatus off completely, you must
disconnect it from the wall outlet. Consequently, the
wall outlet and power plug must be readily accessible
at all times.
• Do not allow children to hang on the product.
• Store the accessories (battery, etc.) in a location safely
out of the reach of children.
• Do not install the product in an unstable location such
asashakyself,aslantedoor,oralocationexposedto
vibration.
• Do not drop or strike the product. If the product is
damaged, disconnect the power cord and contact a
service centre.
• To clean this apparatus, unplug the power cord from
the wall outlet, and then wipe the product using a
soft, dry cloth. Do not use any chemicals such as wax,
benzene, alcohol, thinners, insecticide, air fresheners,
lubricants, or detergent. These chemicals can damage
the appearance of the product or erase the printing on
the product.
• Do not expose this apparatus to dripping or splashing.
Donotputobjectslledwithliquids,suchasvases,on
the apparatus.
• Do not plug multiple electric devices into the same wall
socket. Overloading a socket can cause it to overheat,
resultinginare.
WARNING
• TO PREVENT THE SPREAD OF FIRE,
KEEP CANDLES AND OTHER ITEMS WITH
OPEN FLAMES AWAY FROM
THIS PRODUCT AT ALL TIMES.
• Toreducetheriskofreorelectricshock,donotexpose
this appliance to rain or moisture.
Precautions
1. Ensure that the AC or DC power supply in your house
complies with the power requirements listed on the
identicationstickerlocatedontherearofyourproduct.
Install your product horizontally, on a suitable base
(furniture), with enough space around it forventilation
(7~10 cm). Make sure the ventilation slots are not
covered.Donotplacetheunitonampliersorother
equipment which may become hot. This unit is designed
for continuous use. To fully turn off the unit, disconnect
the AC plug from the wall outlet.
2. Do not expose the unit to direct sunlight or other heat
sources. This could lead to overheating and cause the
unit to malfunction.
3. Unplug the Power cord from the AC wall socket if the
unit malfunctions. Your product is not intended for
industrial use. It is for personal use only. Condensation
may occur if your product has been stored in cold
temperatures. If transporting the unit during the winter,
wait approximately 2 hours until the unit has reached
room temperature before using it.
4. If the electricity supplied to your home is rated at 240V
AC, use a suitable plug adapter to connect this unit to
your electrical outlets.
Important Safety Instructions
Read these operating instructions carefully before using
the unit. Follow all the safety instructions listed below.
Keep these operating instructions handy for future
reference.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus nearwater.
6. Clean onlywith a dry cloth.
7. Do not block anyventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including AV
receivers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided foryour safety. If
theprovidedplugdoesnottintoyouroutlet,consult
an electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where it exits the apparatus.
11. Onlyuseattachments/accessoriesspeciedbythe
manufacturer.
12. Use only with the cart, stand, tripod,
bracket,ortablespeciedbythe
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms orwhen
you intend to leave it unused for long periods of time.
14. Referallservicingtoqualiedservicepersonnel.
Servicing is required when the apparatus has been
damaged in any way, such as when the power-supply
cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
01 CHECKING THE
COMPONENTS
Surround Speaker X 2 / Speaker Cable / AC/DC Adapter
/ Power Cord
NOTE
• For more information about the power supply and
power consumption, refer to the label attached to the
product. (Label: Rear of the Main Unit)
• Designandspecicationsaresubjecttochangewithout
prior notice.
02 CONNECTING THE
SWA-9200S TO A
SOUNDBAR
1. Connect the Surround speaker cables
Use the speaker cables to connect the two surround sound
speakers.
• When connecting the speaker cable, connect the core
wire to the speaker.
• Insert the wire fully, taking care not to insert beyond
the wire insulation.
Insert the wire fully.
+ : Red
- : Black
• When connecting the speaker cables to the surround
speakers, follow these steps:
‒ Insert the red and black colored ends of each
speaker cable into the red and black jacks of the
appropriate speaker.
‒ The labels are on the backs of the speakers.
Audio cable
‒ The length of the speaker audio cable: 6 m
2. Turn on the Surround speakers
Plug the Surround speakers’ power cord into an electrical
outlet to turn on the Surround speakers. The LINK LED
indicator(blue LED) on the rear of left surround speaker will
blink quickly.
If the LINK LED does not blink, please see step 6.
LINK STANDBY
ID SET
Rear of Left
Surround
LINK STANDBY
ID SET
LINK STANDBY
ID SET
Rear of Left Surround
"Blue
blinking"
3. Turn off the Soundbar
If the Soundbar is turned on, please turn off the Soundbar
by pressing the (Power) button on the Soundbar or
remote control.
SOUND
MODE
PAIR
BYE
OR
Red BlinksX3
• The image of the Soundbar may differ from your
Soundbar, depending on the model.
4. Connect Soundbarand Surround Speakers
Press the Up button on the remote control for more than
5 seconds until the “ID SET” message appears on the
Soundbar’s display. The message will disappear shortly.
(If your Soundbar does not have a displaywindow and only
LED indicators, please refer to the LED information below.)
• After the ID SET process is successful, the Soundbarwill
turn on automatically.
OR
SOUND
MODE
PAIR
5 sec
ID SET
Red → Green →
Blue Blinks
• The image of the Soundbar may differ from your
Soundbar, depending on the model.
5. Check the connection complete
The LINK LED stops blinking and changes to solid blue
when the Soundbar and surround speakers are successfully
linked.
PleaseturnofftheSoundbarandturnitbackon.Conrm
that the LINK LED is blue.
(It may take a minute depending on the environment.)
LINK STANDBY
ID SET
LINK STANDBY
ID SET
Rear of Left Surround
“Blue is On”
• If the LINK LED does not turn to solid blue in a minute,
please repeat from step 2 through 5 referring to step 6
(LED indicator’s status).
6. LED Indicator’s status
LINK (Blue) On : Connected with the Soundbar.
LINK (Blue) Blinking fast (at an interval of around
0.5 second) : Surround speakers are in ID SET mode.
• Check if the Soundbar is turned on and in ID SET
mode.
• Repeat steps 3 through 5.
LINK (Blue) Blinking slow (at an interval of around
1 second) : Previously connected to a Soundbar but
cannotcurrentlyndit.
• Check if the Soundbar is turned on.
• If the LINK LED keeps blinking slowly even when the
Soundbar is turned on,
1. Press the ID SET button on the rear of the left
surround for more than 5 seconds until the LINK
LED starts blinking fast in blue.
LINK STANDBY
ID SET
LINK STANDBY
ID SET
5 sec
Rear of Left Surround
2. Repeat steps 3 through 5.
STANDBY (Red) On : When the Soundbar turns off or
connection has failed.
• Follow the instructions for “Link (Blue) Blinking slow
(at an interval of around 1 second)” above.
Others : Errors
• Contact a Samsung Service Centre.
03 TROUBLE SHOOTING
There is no sound from Surround Speakers
• If the Surround speakers are successfully paired and
connected to a Soundbar, the LINK LED indicator on
the rear of the Left Surround is on and solid blue.
Please reconnect the Surround speakers to your
Soundbar referring to 02-6, LED Indicator’s status.
• Other devices sending radio frequency signals in
proximity may interrupt the connection. Please keep
your speaker away from such devices.
• The content you are playing may have no surround
track but only stereo. Please change the sound mode
to Surround by pressing SOUND MODE button on the
remote control.
There is sound jitter, delays, noise or dropout from the
sound of Surround Speakers.
• There may be sound jitter or delays when the Surround
Speakers are far from the Soundbar. Please place
them near the Soundbar.
• There may be sound jitter or delays when the
Soundbar is near an electrical device that can cause
radio interference. Please place the Soundbar far from
such devices that can cause radio interference
(e.g. wireless router).
• Please change the TV network connection status from
wireless to wired.
The volume of Surround Speakers is too low
• Please increase the rear level referring to the manual
of your Soundbar.
(You can download the manual of your Soundbar from
www.samsung.com/support)
04 MOUNTING ON A WALL
LINK STANDBY
8.2 mm
4.2 mm
7.9 mm
4.6 mm
4.0 mm
• Be sure the wall is stable. If the wall is weak, reinforce
it before installation.
• Take care not to install the speakers sideways or upside
down.
• Samsung Electronics is not liable for any damage to the
product due to improper installation.
• Wall mounts aren’t sold by Samsung Electronics.
05 COMPATIBLE MODELS
• Compatible with select Samsung Soundbar. Please visit
the Soundbar product page at www.samsung.com/
support for more information.
• Compatible model list is subject to change without
further notice.
06 OPEN SOURCE LICENSE
NOTICE
To send inquiries and requests for questions regarding
open sources, contact Samsung Open Source
(http://opensource.samsung.com)
07 SPECIFICATIONS AND
GUIDE
Specications
Subwoofer Name
SWA-9200S (LEFT/RIGHT)
Weight
1.7 kg
Dimensions (W x H x D)
105.0 x152.8 x 109.0 mm
Operating Temperature
Range
10℃to40℃
Operating Humidity Range
10 % ~ 80 %,
non-condensing
AMPLIFIER
Rated Output power
60 W x 2
NOTE
• Samsung Electronics Co., Ltd reserves the right to
changethespecicationswithoutnotice.
• Weight and dimensions are approximate.
Country/Area Samsung Service Centre Web Site
CHINA 400-810-5858 www.samsung.com/cn/support
TAIWAN
0800-32-9999 (All Product)
0809-05-5237 (Only for HHP)
0809-00-5237 (B2B / Dealer)
0809-02-6868 (Samsung pay)
www.samsung.com/tw/support
HONG KONG
3698 4698 ( All Product)
3698 4688 ( B2B )
3698 4633 (eStore)
2121 9088 ( Samsung pay )
www.samsung.com/hk/support
(Chinese)
www.samsung.com/hk_en/
support (English)
MACAU 0800 333
SINGAPORE
1800 7267864 |
1800-SAMSUNG (Other)
1800 4252997 |
1800-GALAXYS (HHP)
www.samsung.com/sg/support
AUSTRALIA 1300 362 603 (Other)
1300 425 299 (HHP) www.samsung.com/au/support
NEW ZEALAND
0800 726 786 (All Product)
0800 6 726 786 (Support for
Smart Mobile Devices)
www.samsung.com/nz/support
VIETNAM 1800 588 889 (All Product)
1800-588-855 (HHP) www.samsung.com/vn/support
THAILAND
Hotline no : 1282
1800-29-3232
(Toll free for all product)
www.samsung.com/th/support
MYANMAR [phone]
VIP HHP [phone]
www.samsung.com/mm/
support
CAMBODIA 1800-20-3232 (Toll free) www.samsung.com/th/support
LAOS [phone]
MALAYSIA
1800-22-8899 (HHP)
1800-88-9999 (OTH)
[phone]
(Overseas contact)
www.samsung.com/my/support
Country/Area Samsung Service Centre Web Site
INDONESIA
021-5699-7777
0800-112-8888
(All Product, Toll Free)
0800-112-7777
(All Product, Toll Free)
www.samsung.com/id/support
PHILIPPINES
Dedicated Hotline forMobile
Phones:
#GALAXY (just dial #425299)
All Products :
1-800-10-7267864
[ PLDT - Toll Free ]
1-800-8-7267864
[ Globe - Toll Free ]
84222111 [ Landline ]
www.samsung.com/ph/support
INDIA
1800 5 SAMSUNG
(1800 5 7267864) (Toll-Free)
1800 40 SAMSUNG
(1800 40 7267864) (Toll-Free)
www.samsung.com/in/support
NEPAL
16600172667
(Toll Free forNTC Only)
www.samsung.com/in/
support
9801572667
(Toll Free forNcell users)
SRI LANKA 011 SAMSUNG (011 7267864)
BANGLADESH 08000-300-300 (Toll free)
09612-300-300 www.samsung.com/bd/support

English
User Manual
VA81-01146Q-00
NSPBI01285A-00
SWA-9200S
© 2022 Samsung Electronics Co., Ltd. All rights reserved.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care Centre.
SAFETY INFORMATION
Thank you for purchasing this
product (SWA-9200S).
CAUTION
RISK OF ELECTRIC SHOCK. DO NOT
OPEN.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER (OR BACK). NO USER-
SERVICEABLE PARTS ARE INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL. Refer to the table
below for an explanation of symbols which may be on
your Samsung product.
This symbol indicates that high voltage is
present inside. It is dangerous to make any
kind of contact with any internal part of this
product.
This symbol indicates that this product has
included important literature concerning
operation and maintenance.
Class II product : This symbol indicates that
it does not require a safety connection to
electrical earth (ground).
If this symbol is not present on a product
with a power cord, the product MUST have
a reliable connection to protective earth
(ground).
AC voltage : This symbol indicates that the
rated voltage marked with the symbol is AC
voltage.
DC voltage : This symbol indicates that the
rated voltage marked with the symbol is DC
voltage.
Caution, Consult instructions for use : This
symbol instructs the user to consult the user
manual for further safety related information.
• The slots and openings in the cabinet and in the back or
bottom are provided for necessary ventilation. To ensure
reliable operation of this apparatus, and to protect it
from overheating, these slots and openings must never
be blocked or covered.
‒ Donotplacethisapparatusinaconnedspace,
such as a bookcase, or built-in cabinet, unless proper
ventilation is provided.
‒ Do not place this apparatus near or over a radiator
or heat register, orwhere it is exposed to direct
sunlight.
‒ Do not place vessels (vases etc.) containing water
onthisapparatus.Awaterspillcancauseareor
electric shock.
• Do not expose this apparatus to rain or place it near
water (near a bathtub, washbowl, kitchen sink, or
laundry tub, in a wet basement, or near a swimming
pool, etc.). If this apparatus accidentally gets wet,
unplug it and contact an authorized dealer immediately.
• Do not overload wall outlets, extension cords or
adaptors beyond their capacity, since this can result in
reorelectricshock.
• Route power-supply cords so that they are not likely to
be walked on or pinched by items placed on or against
them. Pay particular attention to cords at the plug end,
at wall outlets, and the point where they exit from the
apparatus.
• To protect this apparatus from a lightning storm, or
when it is left unattended and unused for long periods
of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage
to the set due to lightning and power line surges.
• Before connecting the AC power cord to the DC adaptor
outlet, make sure the voltage designation of the DC
adaptor corresponds to the local electrical supply.
• Never insert anything metallic into the open parts of
this apparatus. Doing so may create a danger of electric
shock.
• To avoid electric shock, never touch the inside of this
apparatus.Onlyaqualiedtechnicianshouldopenthis
apparatus.
• Makesuretoplugthepowercordinuntilitisrmly
seated. When unplugging the power cord from a wall
outlet, always pull on the power cord’s plug. Never
unplug by pulling on the power cord. Do not touch the
power cord with wet hands.
• If this apparatus does not operate normally - in
particular, if there are any unusual sounds or smells
coming from it - unplug it immediately and contact an
authorized dealer or service centre.
• Maintenance of Cabinet.
‒ Before connecting other components to this product,
be sure to turn them off.
• Be sure to pull the power plug out of the outlet if the
product is to remain unused or if you are leaving the
house for an extended period of time (especially when
children, elderly, or disabled people will be left alone in
the house).
‒ Accumulated dust can cause an electric shock, an
electricleakage,orarebycausingthepowercord
to generate sparks and heat or the insulation to
deteriorate.
• Contact an authorized service centre for information
if you intend to install your product in a location with
heavy dust, high or low temperatures, high humidity,
chemical substances, or where it will operate 24 hours
a day such as in an airport, a train station, etc. Failing to
do so may cause serious damage to your product.
• Use only a properly grounded plug and wall outlet.
‒ An improper ground may cause electric shock or
equipment damage. (Class l Equipment only.)
• To turn this apparatus off completely, you must
disconnect it from the wall outlet. Consequently, the
wall outlet and power plug must be readily accessible
at all times.
• Do not allow children to hang on the product.
• Store the accessories (battery, etc.) in a location safely
out of the reach of children.
• Do not install the product in an unstable location such
asashakyself,aslantedoor,oralocationexposedto
vibration.
• Do not drop or strike the product. If the product is
damaged, disconnect the power cord and contact a
service centre.
• To clean this apparatus, unplug the power cord from
the wall outlet, and then wipe the product using a
soft, dry cloth. Do not use any chemicals such as wax,
benzene, alcohol, thinners, insecticide, air fresheners,
lubricants, or detergent. These chemicals can damage
the appearance of the product or erase the printing on
the product.
• Do not expose this apparatus to dripping or splashing.
Donotputobjectslledwithliquids,suchasvases,on
the apparatus.
• Do not plug multiple electric devices into the same wall
socket. Overloading a socket can cause it to overheat,
resultinginare.
WARNING
• TO PREVENT THE SPREAD OF FIRE,
KEEP CANDLES AND OTHER ITEMS WITH
OPEN FLAMES AWAY FROM
THIS PRODUCT AT ALL TIMES.
• Toreducetheriskofreorelectricshock,donotexpose
this appliance to rain or moisture.
Precautions
1. Ensure that the AC or DC power supply in your house
complies with the power requirements listed on the
identicationstickerlocatedontherearofyourproduct.
Install your product horizontally, on a suitable base
(furniture), with enough space around it for ventilation
(7~10 cm). Make sure the ventilation slots are not
covered.Donotplacetheunitonampliersorother
equipment which may become hot. This unit is designed
for continuous use. To fully turn off the unit, disconnect
the AC plug from the wall outlet.
2. Do not expose the unit to direct sunlight or other heat
sources. This could lead to overheating and cause the
unit to malfunction.
3. Unplug the Power cord from the AC wall socket if the
unit malfunctions. Your product is not intended for
industrial use. It is for personal use only. Condensation
may occur if your product has been stored in cold
temperatures. If transporting the unit during the winter,
wait approximately 2 hours until the unit has reached
room temperature before using it.
4. If the electricity supplied to your home is rated at 240V
AC, use a suitable plug adapter to connect this unit to
your electrical outlets.
Important Safety Instructions
Read these operating instructions carefully before using
the unit. Follow all the safety instructions listed below.
Keep these operating instructions handy for future
reference.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including AV
receivers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided foryour safety. If
theprovidedplugdoesnottintoyouroutlet,consult
an electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where it exits the apparatus.
11. Onlyuseattachments/accessoriesspeciedbythe
manufacturer.
12. Use only with the cart, stand, tripod,
bracket,ortablespeciedbythe
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
you intend to leave it unused for long periods of time.
14. Referallservicingtoqualiedservicepersonnel.
Servicing is required when the apparatus has been
damaged in any way, such as when the power-supply
cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
01 CHECKING THE
COMPONENTS
Surround Speaker X 2 / Speaker Cable / AC/DC Adapter
/ Power Cord
NOTE
• For more information about the power supply and
power consumption, refer to the label attached to the
product. (Label: Rear of the Main Unit)
• Designandspecicationsaresubjecttochangewithout
prior notice.
02 CONNECTING THE
SWA-9200S TO A
SOUNDBAR
1. Connect the Surround speaker cables
Use the speaker cables to connect the two surround sound
speakers.
• When connecting the speaker cable, connect the core
wire to the speaker.
• Insert the wire fully, taking care not to insert beyond
the wire insulation.
Insert the wire fully.
+ : Red
- : Black
• When connecting the speaker cables to the surround
speakers, follow these steps:
‒ Insert the red and black colored ends of each
speaker cable into the red and black jacks of the
appropriate speaker.
‒ The labels are on the backs of the speakers.
Audio cable
‒ The length of the speaker audio cable: 6 m
2. Turn on the Surround speakers
Plug the Surround speakers’ power cord into an electrical
outlet to turn on the Surround speakers. The LINK LED
indicator(blue LED) on the rear of left surround speaker will
blink quickly.
If the LINK LED does not blink, please see step 6.
LINK STANDBY
ID SET
Rear of Left
Surround
LINK STANDBY
ID SET
LINK STANDBY
ID SET
Rear of Left Surround
"Blue
blinking"
3. Turn off the Soundbar
If the Soundbar is turned on, please turn off the Soundbar
by pressing the (Power) button on the Soundbar or
remote control.
SOUND
MODE
PAIR
BYE
OR
Red BlinksX3
• The image of the Soundbar may differ from your
Soundbar, depending on the model.
4. Connect Soundbar and Surround Speakers
Press the Up button on the remote control for more than
5 seconds until the “ID SET” message appears on the
Soundbar’s display. The message will disappear shortly.
(If your Soundbar does not have a display window and only
LED indicators, please refer to the LED information below.)
• After the ID SET process is successful, the Soundbarwill
turn on automatically.
OR
SOUND
MODE
PAIR
5 sec
ID SET
Red → Green →
Blue Blinks
• The image of the Soundbar may differ from your
Soundbar, depending on the model.
5. Check the connection complete
The LINK LED stops blinking and changes to solid blue
when the Soundbar and surround speakers are successfully
linked.
PleaseturnofftheSoundbarandturnitbackon.Conrm
that the LINK LED is blue.
(It may take a minute depending on the environment.)
LINK STANDBY
ID SET
LINK STANDBY
ID SET
Rear of Left Surround
“Blue is On”
• If the LINK LED does not turn to solid blue in a minute,
please repeat from step 2 through 5 referring to step 6
(LED indicator’s status).
6. LED Indicator’s status
LINK (Blue) On : Connected with the Soundbar.
LINK (Blue) Blinking fast (at an interval of around
0.5 second) : Surround speakers are in ID SET mode.
• Check if the Soundbar is turned on and in ID SET
mode.
• Repeat steps 3 through 5.
LINK (Blue) Blinking slow (at an interval of around
1 second) : Previously connected to a Soundbar but
cannotcurrentlyndit.
• Check if the Soundbar is turned on.
• If the LINK LED keeps blinking slowly even when the
Soundbar is turned on,
1. Press the ID SET button on the rear of the left
surround for more than 5 seconds until the LINK
LED starts blinking fast in blue.
LINK STANDBY
ID SET
LINK STANDBY
ID SET
5 sec
Rear of Left Surround
2. Repeat steps 3 through 5.
STANDBY (Red) On : When the Soundbar turns off or
connection has failed.
• Follow the instructions for “Link (Blue) Blinking slow
(at an interval of around 1 second)” above.
Others : Errors
• Contact a Samsung Service Centre.
03 TROUBLE SHOOTING
There is no sound from Surround Speakers
• If the Surround speakers are successfully paired and
connected to a Soundbar, the LINK LED indicator on
the rear of the Left Surround is on and solid blue.
Please reconnect the Surround speakers to your
Soundbar referring to 02-6, LED Indicator’s status.
• Other devices sending radio frequency signals in
proximity may interrupt the connection. Please keep
your speaker away from such devices.
• The content you are playing may have no surround
track but only stereo. Please change the sound mode
to Surround by pressing SOUND MODE button on the
remote control.
There is sound jitter, delays, noise or dropout from the
sound of Surround Speakers.
• There may be sound jitter or delays when the Surround
Speakers are far from the Soundbar. Please place
them near the Soundbar.
• There may be sound jitter or delays when the
Soundbar is near an electrical device that can cause
radio interference. Please place the Soundbar far from
such devices that can cause radio interference
(e.g. wireless router).
• Please change the TV network connection status from
wireless to wired.
The volume of Surround Speakers is too low
• Please increase the rear level referring to the manual
of your Soundbar.
(You can download the manual of your Soundbar from
www.samsung.com/support)
04 MOUNTING ON A WALL
LINK STANDBY
8.2 mm
4.2 mm
7.9 mm
4.6 mm
4.0 mm
• Be sure the wall is stable. If the wall is weak, reinforce
it before installation.
• Take care not to install the speakers sideways or upside
down.
• Samsung Electronics is not liable for any damage to the
product due to improper installation.
• Wall mounts aren’t sold by Samsung Electronics.
05 COMPATIBLE MODELS
• Compatible with select Samsung Soundbar. Please visit
the Soundbar product page at www.samsung.com/
support for more information.
• Compatible model list is subject to change without
further notice.
06 OPEN SOURCE LICENSE
NOTICE
To send inquiries and requests for questions regarding
open sources, contact Samsung Open Source
(http://opensource.samsung.com)
07 SPECIFICATIONS AND
GUIDE
Specications
Subwoofer Name
SWA-9200S (LEFT/RIGHT)
Weight
1.7 kg
Dimensions (W x H x D)
105.0 x 152.8 x 109.0 mm
Operating Temperature
Range
10℃to40℃
Operating Humidity Range
10 % ~ 80 %,
non-condensing
AMPLIFIER
Rated Output power
60 W x 2
NOTE
• Samsung Electronics Co., Ltd reserves the right to
changethespecicationswithoutnotice.
• Weight and dimensions are approximate.
Country/Area Samsung Service Centre Web Site
CHINA 400-810-5858 www.samsung.com/cn/support
TAIWAN
0800-32-9999 (All Product)
0809-05-5237 (Only for HHP)
0809-00-5237 (B2B / Dealer)
0809-02-6868 (Samsung pay)
www.samsung.com/tw/support
HONG KONG
3698 4698 ( All Product)
3698 4688 ( B2B )
3698 4633 (eStore)
2121 9088 ( Samsung pay )
www.samsung.com/hk/support
(Chinese)
www.samsung.com/hk_en/
support (English)
MACAU 0800 333
SINGAPORE
1800 7267864 |
1800-SAMSUNG (Other)
1800 4252997 |
1800-GALAXYS (HHP)
www.samsung.com/sg/support
AUSTRALIA 1300 362 603 (Other)
1300 425 299 (HHP) www.samsung.com/au/support
NEW ZEALAND
0800 726 786 (All Product)
0800 6 726 786 (Support for
Smart Mobile Devices)
www.samsung.com/nz/support
VIETNAM 1800 588 889 (All Product)
1800-588-855 (HHP) www.samsung.com/vn/support
THAILAND
Hotline no : 1282
1800-29-3232
(Toll free for all product)
www.samsung.com/th/support
MYANMAR [phone]
VIP HHP [phone]
www.samsung.com/mm/
support
CAMBODIA 1800-20-3232 (Toll free) www.samsung.com/th/support
LAOS [phone]
MALAYSIA
1800-22-8899 (HHP)
1800-88-9999 (OTH)
[phone]
(Overseas contact)
www.samsung.com/my/support
Country/Area Samsung Service Centre Web Site
INDONESIA
021-5699-7777
0800-112-8888
(All Product, Toll Free)
0800-112-7777
(All Product, Toll Free)
www.samsung.com/id/support
PHILIPPINES
Dedicated Hotline for Mobile
Phones:
#GALAXY (just dial #425299)
All Products :
1-800-10-7267864
[ PLDT - Toll Free ]
1-800-8-7267864
[ Globe - Toll Free ]
84222111 [ Landline ]
www.samsung.com/ph/support
INDIA
1800 5 SAMSUNG
(1800 5 7267864) (Toll-Free)
1800 40 SAMSUNG
(1800 40 7267864) (Toll-Free)
www.samsung.com/in/support
NEPAL
16600172667
(Toll Free for NTC Only)
www.samsung.com/in/
support
9801572667
(Toll Free for Ncell users)
SRI LANKA 011 SAMSUNG (011 7267864)
BANGLADESH 08000-300-300 (Toll free)
09612-300-300 www.samsung.com/bd/support

English
User Manual
VA81-01146Q-00
NSPBI01285A-00
SWA-9200S
© 2022 Samsung Electronics Co., Ltd. All rights reserved.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care Centre.
SAFETY INFORMATION
Thank you for purchasing this
product (SWA-9200S).
CAUTION
RISK OF ELECTRIC SHOCK. DO NOT
OPEN.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER (OR BACK). NO USER-
SERVICEABLE PARTS ARE INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL. Refer to the table
below for an explanation of symbols which may be on
your Samsung product.
This symbol indicates that high voltage is
present inside. It is dangerous to make any
kind of contact with any internal part of this
product.
This symbol indicates that this product has
included important literature concerning
operation and maintenance.
Class II product : This symbol indicates that
it does not require a safety connection to
electrical earth (ground).
If this symbol is not present on a product
with a power cord, the product MUST have
a reliable connection to protective earth
(ground).
AC voltage : This symbol indicates that the
rated voltage marked with the symbol is AC
voltage.
DC voltage : This symbol indicates that the
rated voltage marked with the symbol is DC
voltage.
Caution, Consult instructions for use : This
symbol instructs the user to consult the user
manual for further safety related information.
• The slots and openings in the cabinet and in the back or
bottom are provided for necessary ventilation. To ensure
reliable operation of this apparatus, and to protect it
from overheating, these slots and openings must never
be blocked or covered.
‒ Donotplacethisapparatusinaconnedspace,
such as a bookcase, or built-in cabinet, unless proper
ventilation is provided.
‒ Do not place this apparatus near or over a radiator
or heat register, orwhere it is exposed to direct
sunlight.
‒ Do not place vessels (vases etc.) containing water
onthisapparatus.Awaterspillcancauseareor
electric shock.
• Do not expose this apparatus to rain or place it near
water (near a bathtub, washbowl, kitchen sink, or
laundry tub, in a wet basement, or near a swimming
pool, etc.). If this apparatus accidentally gets wet,
unplug it and contact an authorized dealer immediately.
• Do not overload wall outlets, extension cords or
adaptors beyond their capacity, since this can result in
reorelectricshock.
• Route power-supply cords so that they are not likely to
be walked on or pinched by items placed on or against
them. Pay particular attention to cords at the plug end,
at wall outlets, and the point where they exit from the
apparatus.
• To protect this apparatus from a lightning storm, or
when it is left unattended and unused for long periods
of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage
to the set due to lightning and power line surges.
• Before connecting the AC power cord to the DC adaptor
outlet, make sure the voltage designation of the DC
adaptor corresponds to the local electrical supply.
• Never insert anything metallic into the open parts of
this apparatus. Doing so may create a danger of electric
shock.
• To avoid electric shock, never touch the inside of this
apparatus.Onlyaqualiedtechnicianshouldopenthis
apparatus.
• Makesuretoplugthepowercordinuntilitisrmly
seated. When unplugging the power cord from a wall
outlet, always pull on the power cord’s plug. Never
unplug by pulling on the power cord. Do not touch the
power cord with wet hands.
• If this apparatus does not operate normally - in
particular, if there are any unusual sounds or smells
coming from it - unplug it immediately and contact an
authorized dealer or service centre.
• Maintenance of Cabinet.
‒ Before connecting other components to this product,
be sure to turn them off.
• Be sure to pull the power plug out of the outlet if the
product is to remain unused or if you are leaving the
house for an extended period of time (especially when
children, elderly, or disabled people will be left alone in
the house).
‒ Accumulated dust can cause an electric shock, an
electricleakage,orarebycausingthepowercord
to generate sparks and heat or the insulation to
deteriorate.
• Contact an authorized service centre for information
if you intend to install your product in a location with
heavy dust, high or low temperatures, high humidity,
chemical substances, or where it will operate 24 hours
a day such as in an airport, a train station, etc. Failing to
do so may cause serious damage to your product.
• Use only a properly grounded plug and wall outlet.
‒ An improper ground may cause electric shock or
equipment damage. (Class l Equipment only.)
• To turn this apparatus off completely, you must
disconnect it from the wall outlet. Consequently, the
wall outlet and power plug must be readily accessible
at all times.
• Do not allow children to hang on the product.
• Store the accessories (battery, etc.) in a location safely
out of the reach of children.
• Do not install the product in an unstable location such
asashakyself,aslantedoor,oralocationexposedto
vibration.
• Do not drop or strike the product. If the product is
damaged, disconnect the power cord and contact a
service centre.
• To clean this apparatus, unplug the power cord from
the wall outlet, and then wipe the product using a
soft, dry cloth. Do not use any chemicals such as wax,
benzene, alcohol, thinners, insecticide, air fresheners,
lubricants, or detergent. These chemicals can damage
the appearance of the product or erase the printing on
the product.
• Do not expose this apparatus to dripping or splashing.
Donotputobjectslledwithliquids,suchasvases,on
the apparatus.
• Do not plug multiple electric devices into the same wall
socket. Overloading a socket can cause it to overheat,
resultinginare.
WARNING
• TO PREVENT THE SPREAD OF FIRE,
KEEP CANDLES AND OTHER ITEMS WITH
OPEN FLAMES AWAY FROM
THIS PRODUCT AT ALL TIMES.
• Toreducetheriskofreorelectricshock,donotexpose
this appliance to rain or moisture.
Precautions
1. Ensure that the AC or DC power supply in your house
complies with the power requirements listed on the
identicationstickerlocatedontherearofyourproduct.
Install your product horizontally, on a suitable base
(furniture), with enough space around it forventilation
(7~10 cm). Make sure the ventilation slots are not
covered.Donotplacetheunitonampliersorother
equipment which may become hot. This unit is designed
for continuous use. To fully turn off the unit, disconnect
the AC plug from the wall outlet.
2. Do not expose the unit to direct sunlight or other heat
sources. This could lead to overheating and cause the
unit to malfunction.
3. Unplug the Power cord from the AC wall socket if the
unit malfunctions. Your product is not intended for
industrial use. It is for personal use only. Condensation
may occur if your product has been stored in cold
temperatures. If transporting the unit during the winter,
wait approximately 2 hours until the unit has reached
room temperature before using it.
4. If the electricity supplied to your home is rated at 240V
AC, use a suitable plug adapter to connect this unit to
your electrical outlets.
Important Safety Instructions
Read these operating instructions carefully before using
the unit. Follow all the safety instructions listed below.
Keep these operating instructions handy for future
reference.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including AV
receivers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided foryour safety. If
theprovidedplugdoesnottintoyouroutlet,consult
an electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where it exits the apparatus.
11. Onlyuseattachments/accessoriesspeciedbythe
manufacturer.
12. Use only with the cart, stand, tripod,
bracket,ortablespeciedbythe
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
you intend to leave it unused for long periods of time.
14. Referallservicingtoqualiedservicepersonnel.
Servicing is required when the apparatus has been
damaged in any way, such as when the power-supply
cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
01 CHECKING THE
COMPONENTS
Surround Speaker X 2 / Speaker Cable / AC/DC Adapter
/ Power Cord
NOTE
• For more information about the power supply and
power consumption, refer to the label attached to the
product. (Label: Rear of the Main Unit)
• Designandspecicationsaresubjecttochangewithout
prior notice.
02 CONNECTING THE
SWA-9200S TO A
SOUNDBAR
1. Connect the Surround speaker cables
Use the speaker cables to connect the two surround sound
speakers.
• When connecting the speaker cable, connect the core
wire to the speaker.
• Insert the wire fully, taking care not to insert beyond
the wire insulation.
Insert the wire fully.
+ : Red
- : Black
• When connecting the speaker cables to the surround
speakers, follow these steps:
‒ Insert the red and black colored ends of each
speaker cable into the red and black jacks of the
appropriate speaker.
‒ The labels are on the backs of the speakers.
Audio cable
‒ The length of the speaker audio cable: 6 m
2. Turn on the Surround speakers
Plug the Surround speakers’ power cord into an electrical
outlet to turn on the Surround speakers. The LINK LED
indicator(blue LED) on the rear of left surround speaker will
blink quickly.
If the LINK LED does not blink, please see step 6.
LINK STANDBY
ID SET
Rear of Left
Surround
LINK STANDBY
ID SET
LINK STANDBY
ID SET
Rear of Left Surround
"Blue
blinking"
3. Turn off the Soundbar
If the Soundbar is turned on, please turn off the Soundbar
by pressing the (Power) button on the Soundbar or
remote control.
SOUND
MODE
PAIR
BYE
OR
Red BlinksX3
• The image of the Soundbar may differ from your
Soundbar, depending on the model.
4. Connect Soundbar and Surround Speakers
Press the Up button on the remote control for more than
5 seconds until the “ID SET” message appears on the
Soundbar’s display. The message will disappear shortly.
(If your Soundbar does not have a display window and only
LED indicators, please refer to the LED information below.)
• After the ID SET process is successful, the Soundbar will
turn on automatically.
OR
SOUND
MODE
PAIR
5 sec
ID SET
Red → Green →
Blue Blinks
• The image of the Soundbar may differ from your
Soundbar, depending on the model.
5. Check the connection complete
The LINK LED stops blinking and changes to solid blue
when the Soundbar and surround speakers are successfully
linked.
PleaseturnofftheSoundbarandturnitbackon.Conrm
that the LINK LED is blue.
(It may take a minute depending on the environment.)
LINK STANDBY
ID SET
LINK STANDBY
ID SET
Rear of Left Surround
“Blue is On”
• If the LINK LED does not turn to solid blue in a minute,
please repeat from step 2 through 5 referring to step 6
(LED indicator’s status).
6. LED Indicator’s status
LINK (Blue) On : Connected with the Soundbar.
LINK (Blue) Blinking fast (at an interval of around
0.5 second) : Surround speakers are in ID SET mode.
• Check if the Soundbar is turned on and in ID SET
mode.
• Repeat steps 3 through 5.
LINK (Blue) Blinking slow (at an interval of around
1 second) : Previously connected to a Soundbar but
cannotcurrentlyndit.
• Check if the Soundbar is turned on.
• If the LINK LED keeps blinking slowly even when the
Soundbar is turned on,
1. Press the ID SET button on the rear of the left
surround for more than 5 seconds until the LINK
LED starts blinking fast in blue.
LINK STANDBY
ID SET
LINK STANDBY
ID SET
5 sec
Rear of Left Surround
2. Repeat steps 3 through 5.
STANDBY (Red) On : When the Soundbar turns off or
connection has failed.
• Follow the instructions for “Link (Blue) Blinking slow
(at an interval of around 1 second)” above.
Others : Errors
• Contact a Samsung Service Centre.
03 TROUBLE SHOOTING
There is no sound from Surround Speakers
• If the Surround speakers are successfully paired and
connected to a Soundbar, the LINK LED indicator on
the rear of the Left Surround is on and solid blue.
Please reconnect the Surround speakers to your
Soundbar referring to 02-6, LED Indicator’s status.
• Other devices sending radio frequency signals in
proximity may interrupt the connection. Please keep
your speaker away from such devices.
• The content you are playing may have no surround
track but only stereo. Please change the sound mode
to Surround by pressing SOUND MODE button on the
remote control.
There is sound jitter, delays, noise or dropout from the
sound of Surround Speakers.
• There may be sound jitter or delays when the Surround
Speakers are far from the Soundbar. Please place
them near the Soundbar.
• There may be sound jitter or delays when the
Soundbar is near an electrical device that can cause
radio interference. Please place the Soundbar far from
such devices that can cause radio interference
(e.g. wireless router).
• Please change the TV network connection status from
wireless to wired.
The volume of Surround Speakers is too low
• Please increase the rear level referring to the manual
of your Soundbar.
(You can download the manual of your Soundbar from
www.samsung.com/support)
04 MOUNTING ON A WALL
LINK STANDBY
8.2 mm
4.2 mm
7.9 mm
4.6 mm
4.0 mm
• Be sure the wall is stable. If the wall is weak, reinforce
it before installation.
• Take care not to install the speakers sideways or upside
down.
• Samsung Electronics is not liable for any damage to the
product due to improper installation.
• Wall mounts aren’t sold by Samsung Electronics.
05 COMPATIBLE MODELS
• Compatible with select Samsung Soundbar. Please visit
the Soundbar product page at www.samsung.com/
support for more information.
• Compatible model list is subject to change without
further notice.
06 OPEN SOURCE LICENSE
NOTICE
To send inquiries and requests for questions regarding
open sources, contact Samsung Open Source
(http://opensource.samsung.com)
07 SPECIFICATIONS AND
GUIDE
Specications
Subwoofer Name
SWA-9200S (LEFT/RIGHT)
Weight
1.7 kg
Dimensions (W x H x D)
105.0 x 152.8 x 109.0 mm
Operating Temperature
Range
10℃to40℃
Operating Humidity Range
10 % ~ 80 %,
non-condensing
AMPLIFIER
Rated Output power
60 W x 2
NOTE
• Samsung Electronics Co., Ltd reserves the right to
changethespecicationswithoutnotice.
• Weight and dimensions are approximate.
Country/Area Samsung Service Centre Web Site
CHINA 400-810-5858 www.samsung.com/cn/support
TAIWAN
0800-32-9999 (All Product)
0809-05-5237 (Only for HHP)
0809-00-5237 (B2B / Dealer)
0809-02-6868 (Samsung pay)
www.samsung.com/tw/support
HONG KONG
3698 4698 ( All Product)
3698 4688 ( B2B )
3698 4633 (eStore)
2121 9088 ( Samsung pay )
www.samsung.com/hk/support
(Chinese)
www.samsung.com/hk_en/
support (English)
MACAU 0800 333
SINGAPORE
1800 7267864 |
1800-SAMSUNG (Other)
1800 4252997 |
1800-GALAXYS (HHP)
www.samsung.com/sg/support
AUSTRALIA 1300 362 603 (Other)
1300 425 299 (HHP) www.samsung.com/au/support
NEW ZEALAND
0800 726 786 (All Product)
0800 6 726 786 (Support for
Smart Mobile Devices)
www.samsung.com/nz/support
VIETNAM 1800 588 889 (All Product)
1800-588-855 (HHP) www.samsung.com/vn/support
THAILAND
Hotline no : 1282
1800-29-3232
(Toll free for all product)
www.samsung.com/th/support
MYANMAR [phone]
VIP HHP [phone]
www.samsung.com/mm/
support
CAMBODIA 1800-20-3232 (Toll free) www.samsung.com/th/support
LAOS [phone]
MALAYSIA
1800-22-8899 (HHP)
1800-88-9999 (OTH)
[phone]
(Overseas contact)
www.samsung.com/my/support
Country/Area Samsung Service Centre Web Site
INDONESIA
021-5699-7777
0800-112-8888
(All Product, Toll Free)
0800-112-7777
(All Product, Toll Free)
www.samsung.com/id/support
PHILIPPINES
Dedicated Hotline for Mobile
Phones:
#GALAXY (just dial #425299)
All Products :
1-800-10-7267864
[ PLDT - Toll Free ]
1-800-8-7267864
[ Globe - Toll Free ]
84222111 [ Landline ]
www.samsung.com/ph/support
INDIA
1800 5 SAMSUNG
(1800 5 7267864) (Toll-Free)
1800 40 SAMSUNG
(1800 40 7267864) (Toll-Free)
www.samsung.com/in/support
NEPAL
16600172667
(Toll Free for NTC Only)
www.samsung.com/in/
support
9801572667
(Toll Free for Ncell users)
SRI LANKA 011 SAMSUNG (011 7267864)
BANGLADESH 08000-300-300 (Toll free)
09612-300-300 www.samsung.com/bd/support

English
User Manual
VA81-01146Q-00
NSPBI01285A-00
SWA-9200S
© 2022 Samsung Electronics Co., Ltd. All rights reserved.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care Centre.
SAFETY INFORMATION
Thank you for purchasing this
product (SWA-9200S).
CAUTION
RISK OF ELECTRIC SHOCK. DO NOT
OPEN.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER (OR BACK). NO USER-
SERVICEABLE PARTS ARE INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL. Refer to the table
below for an explanation of symbols which may be on
your Samsung product.
This symbol indicates that high voltage is
present inside. It is dangerous to make any
kind of contact with any internal part of this
product.
This symbol indicates that this product has
included important literature concerning
operation and maintenance.
Class II product : This symbol indicates that
it does not require a safety connection to
electrical earth (ground).
If this symbol is not present on a product
with a power cord, the product MUST have
a reliable connection to protective earth
(ground).
AC voltage : This symbol indicates that the
rated voltage marked with the symbol is AC
voltage.
DC voltage : This symbol indicates that the
rated voltage marked with the symbol is DC
voltage.
Caution, Consult instructions for use : This
symbol instructs the user to consult the user
manual for further safety related information.
• The slots and openings in the cabinet and in the back or
bottom are provided for necessary ventilation. To ensure
reliable operation of this apparatus, and to protect it
from overheating, these slots and openings must never
be blocked or covered.
‒ Donotplacethisapparatusinaconnedspace,
such as a bookcase, or built-in cabinet, unless proper
ventilation is provided.
‒ Do not place this apparatus near or over a radiator
or heat register, or where it is exposed to direct
sunlight.
‒ Do not place vessels (vases etc.) containing water
onthisapparatus.Awaterspillcancauseareor
electric shock.
• Do not expose this apparatus to rain or place it near
water (near a bathtub, washbowl, kitchen sink, or
laundry tub, in a wet basement, or near a swimming
pool, etc.). If this apparatus accidentally gets wet,
unplug it and contact an authorized dealer immediately.
• Do not overload wall outlets, extension cords or
adaptors beyond their capacity, since this can result in
reorelectricshock.
• Route power-supply cords so that they are not likely to
be walked on or pinched by items placed on or against
them. Pay particular attention to cords at the plug end,
at wall outlets, and the point where they exit from the
apparatus.
• To protect this apparatus from a lightning storm, or
when it is left unattended and unused for long periods
of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage
to the set due to lightning and power line surges.
• Before connecting the AC power cord to the DC adaptor
outlet, make sure the voltage designation of the DC
adaptor corresponds to the local electrical supply.
• Never insert anything metallic into the open parts of
this apparatus. Doing so may create a danger of electric
shock.
• To avoid electric shock, never touch the inside of this
apparatus.Onlyaqualiedtechnicianshouldopenthis
apparatus.
• Makesuretoplugthepowercordinuntilitisrmly
seated. When unplugging the power cord from a wall
outlet, always pull on the power cord’s plug. Never
unplug by pulling on the power cord. Do not touch the
power cord with wet hands.
• If this apparatus does not operate normally - in
particular, if there are any unusual sounds or smells
coming from it - unplug it immediately and contact an
authorized dealer or service centre.
• Maintenance of Cabinet.
‒ Before connecting other components to this product,
be sure to turn them off.
• Be sure to pull the power plug out of the outlet if the
product is to remain unused or if you are leaving the
house for an extended period of time (especially when
children, elderly, or disabled people will be left alone in
the house).
‒ Accumulated dust can cause an electric shock, an
electricleakage,orarebycausingthepowercord
to generate sparks and heat or the insulation to
deteriorate.
• Contact an authorized service centre for information
if you intend to install your product in a location with
heavy dust, high or low temperatures, high humidity,
chemical substances, or where it will operate 24 hours
a day such as in an airport, a train station, etc. Failing to
do so may cause serious damage to your product.
• Use only a properly grounded plug and wall outlet.
‒ An improper ground may cause electric shock or
equipment damage. (Class l Equipment only.)
• To turn this apparatus off completely, you must
disconnect it from the wall outlet. Consequently, the
wall outlet and power plug must be readily accessible
at all times.
• Do not allow children to hang on the product.
• Store the accessories (battery, etc.) in a location safely
out of the reach of children.
• Do not install the product in an unstable location such
asashakyself,aslantedoor,oralocationexposedto
vibration.
• Do not drop or strike the product. If the product is
damaged, disconnect the power cord and contact a
service centre.
• To clean this apparatus, unplug the power cord from
the wall outlet, and then wipe the product using a
soft, dry cloth. Do not use any chemicals such as wax,
benzene, alcohol, thinners, insecticide, air fresheners,
lubricants, or detergent. These chemicals can damage
the appearance of the product or erase the printing on
the product.
• Do not expose this apparatus to dripping or splashing.
Donotputobjectslledwithliquids,suchasvases,on
the apparatus.
• Do not plug multiple electric devices into the same wall
socket. Overloading a socket can cause it to overheat,
resultinginare.
WARNING
• TO PREVENT THE SPREAD OF FIRE,
KEEP CANDLES AND OTHER ITEMS WITH
OPEN FLAMES AWAY FROM
THIS PRODUCT AT ALL TIMES.
• Toreducetheriskofreorelectricshock,donotexpose
this appliance to rain or moisture.
Precautions
1. Ensure that the AC or DC power supply in your house
complies with the power requirements listed on the
identicationstickerlocatedontherearofyourproduct.
Install your product horizontally, on a suitable base
(furniture), with enough space around it forventilation
(7~10 cm). Make sure the ventilation slots are not
covered.Donotplacetheunitonampliersorother
equipment which may become hot. This unit is designed
for continuous use. To fully turn off the unit, disconnect
the AC plug from the wall outlet.
2. Do not expose the unit to direct sunlight or other heat
sources. This could lead to overheating and cause the
unit to malfunction.
3. Unplug the Power cord from the AC wall socket if the
unit malfunctions. Your product is not intended for
industrial use. It is for personal use only. Condensation
may occur if your product has been stored in cold
temperatures. If transporting the unit during the winter,
wait approximately 2 hours until the unit has reached
room temperature before using it.
4. If the electricity supplied to your home is rated at 240V
AC, use a suitable plug adapter to connect this unit to
your electrical outlets.
Important Safety Instructions
Read these operating instructions carefully before using
the unit. Follow all the safety instructions listed below.
Keep these operating instructions handy for future
reference.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including AV
receivers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided foryour safety. If
theprovidedplugdoesnottintoyouroutlet,consult
an electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where it exits the apparatus.
11. Onlyuseattachments/accessoriesspeciedbythe
manufacturer.
12. Use only with the cart, stand, tripod,
bracket,ortablespeciedbythe
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
you intend to leave it unused for long periods of time.
14. Referallservicingtoqualiedservicepersonnel.
Servicing is required when the apparatus has been
damaged in any way, such as when the power-supply
cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
01 CHECKING THE
COMPONENTS
Surround Speaker X 2 / Speaker Cable / AC/DC Adapter
/ Power Cord
NOTE
• For more information about the power supply and
power consumption, refer to the label attached to the
product. (Label: Rear of the Main Unit)
• Designandspecicationsaresubjecttochangewithout
prior notice.
02 CONNECTING THE
SWA-9200S TO A
SOUNDBAR
1. Connect the Surround speaker cables
Use the speaker cables to connect the two surround sound
speakers.
• When connecting the speaker cable, connect the core
wire to the speaker.
• Insert the wire fully, taking care not to insert beyond
the wire insulation.
Insert the wire fully.
+ : Red
- : Black
• When connecting the speaker cables to the surround
speakers, follow these steps:
‒ Insert the red and black colored ends of each
speaker cable into the red and black jacks of the
appropriate speaker.
‒ The labels are on the backs of the speakers.
Audio cable
‒ The length of the speaker audio cable: 6 m
2. Turn on the Surround speakers
Plug the Surround speakers’ power cord into an electrical
outlet to turn on the Surround speakers. The LINK LED
indicator(blue LED) on the rear of left surround speaker will
blink quickly.
If the LINK LED does not blink, please see step 6.
LINK STANDBY
ID SET
Rear of Left
Surround
LINK STANDBY
ID SET
LINK STANDBY
ID SET
Rear of Left Surround
"Blue
blinking"
3. Turn off the Soundbar
If the Soundbar is turned on, please turn off the Soundbar
by pressing the (Power) button on the Soundbar or
remote control.
SOUND
MODE
PAIR
BYE
OR
Red BlinksX3
• The image of the Soundbar may differ from your
Soundbar, depending on the model.
4. Connect Soundbar and Surround Speakers
Press the Up button on the remote control for more than
5 seconds until the “ID SET” message appears on the
Soundbar’s display. The message will disappear shortly.
(If your Soundbar does not have a display window and only
LED indicators, please refer to the LED information below.)
• After the ID SET process is successful, the Soundbar will
turn on automatically.
OR
SOUND
MODE
PAIR
5 sec
ID SET
Red → Green →
Blue Blinks
• The image of the Soundbar may differ from your
Soundbar, depending on the model.
5. Check the connection complete
The LINK LED stops blinking and changes to solid blue
when the Soundbar and surround speakers are successfully
linked.
PleaseturnofftheSoundbarandturnitbackon.Conrm
that the LINK LED is blue.
(It may take a minute depending on the environment.)
LINK STANDBY
ID SET
LINK STANDBY
ID SET
Rear of Left Surround
“Blue is On”
• If the LINK LED does not turn to solid blue in a minute,
please repeat from step 2 through 5 referring to step 6
(LED indicator’s status).
6. LED Indicator’s status
LINK (Blue) On : Connected with the Soundbar.
LINK (Blue) Blinking fast (at an interval of around
0.5 second) : Surround speakers are in ID SET mode.
• Check if the Soundbar is turned on and in ID SET
mode.
• Repeat steps 3 through 5.
LINK (Blue) Blinking slow (at an interval of around
1 second) : Previously connected to a Soundbar but
cannotcurrentlyndit.
• Check if the Soundbar is turned on.
• If the LINK LED keeps blinking slowly even when the
Soundbar is turned on,
1. Press the ID SET button on the rear of the left
surround for more than 5 seconds until the LINK
LED starts blinking fast in blue.
LINK STANDBY
ID SET
LINK STANDBY
ID SET
5 sec
Rear of Left Surround
2. Repeat steps 3 through 5.
STANDBY (Red) On : When the Soundbar turns off or
connection has failed.
• Follow the instructions for “Link (Blue) Blinking slow
(at an interval of around 1 second)” above.
Others : Errors
• Contact a Samsung Service Centre.
03 TROUBLE SHOOTING
There is no sound from Surround Speakers
• If the Surround speakers are successfully paired and
connected to a Soundbar, the LINK LED indicator on
the rear of the Left Surround is on and solid blue.
Please reconnect the Surround speakers to your
Soundbar referring to 02-6, LED Indicator’s status.
• Other devices sending radio frequency signals in
proximity may interrupt the connection. Please keep
your speaker away from such devices.
• The content you are playing may have no surround
track but only stereo. Please change the sound mode
to Surround by pressing SOUND MODE button on the
remote control.
There is sound jitter, delays, noise or dropout from the
sound of Surround Speakers.
• There may be sound jitter or delays when the Surround
Speakers are far from the Soundbar. Please place
them near the Soundbar.
• There may be sound jitter or delays when the
Soundbar is near an electrical device that can cause
radio interference. Please place the Soundbar far from
such devices that can cause radio interference
(e.g. wireless router).
• Please change the TV network connection status from
wireless to wired.
The volume of Surround Speakers is too low
• Please increase the rear level referring to the manual
of your Soundbar.
(You can download the manual of your Soundbar from
www.samsung.com/support)
04 MOUNTING ON A WALL
LINK STANDBY
8.2 mm
4.2 mm
7.9 mm
4.6 mm
4.0 mm
• Be sure the wall is stable. If the wall is weak, reinforce
it before installation.
• Take care not to install the speakers sideways or upside
down.
• Samsung Electronics is not liable for any damage to the
product due to improper installation.
• Wall mounts aren’t sold by Samsung Electronics.
05 COMPATIBLE MODELS
• Compatible with select Samsung Soundbar. Please visit
the Soundbar product page at www.samsung.com/
support for more information.
• Compatible model list is subject to change without
further notice.
06 OPEN SOURCE LICENSE
NOTICE
To send inquiries and requests for questions regarding
open sources, contact Samsung Open Source
(http://opensource.samsung.com)
07 SPECIFICATIONS AND
GUIDE
Specications
Subwoofer Name
SWA-9200S (LEFT/RIGHT)
Weight
1.7 kg
Dimensions (W x H x D)
105.0 x 152.8 x 109.0 mm
Operating Temperature
Range
10℃to40℃
Operating Humidity Range
10 % ~ 80 %,
non-condensing
AMPLIFIER
Rated Output power
60 W x 2
NOTE
• Samsung Electronics Co., Ltd reserves the right to
changethespecicationswithoutnotice.
• Weight and dimensions are approximate.
Country/Area Samsung Service Centre Web Site
CHINA 400-810-5858 www.samsung.com/cn/support
TAIWAN
0800-32-9999 (All Product)
0809-05-5237 (Only for HHP)
0809-00-5237 (B2B / Dealer)
0809-02-6868 (Samsung pay)
www.samsung.com/tw/support
HONG KONG
3698 4698 ( All Product)
3698 4688 ( B2B )
3698 4633 (eStore)
2121 9088 ( Samsung pay )
www.samsung.com/hk/support
(Chinese)
www.samsung.com/hk_en/
support (English)
MACAU 0800 333
SINGAPORE
1800 7267864 |
1800-SAMSUNG (Other)
1800 4252997 |
1800-GALAXYS (HHP)
www.samsung.com/sg/support
AUSTRALIA 1300 362 603 (Other)
1300 425 299 (HHP) www.samsung.com/au/support
NEW ZEALAND
0800 726 786 (All Product)
0800 6 726 786 (Support for
Smart Mobile Devices)
www.samsung.com/nz/support
VIETNAM 1800 588 889 (All Product)
1800-588-855 (HHP) www.samsung.com/vn/support
THAILAND
Hotline no : 1282
1800-29-3232
(Toll free for all product)
www.samsung.com/th/support
MYANMAR [phone]
VIP HHP [phone]
www.samsung.com/mm/
support
CAMBODIA 1800-20-3232 (Toll free) www.samsung.com/th/support
LAOS [phone]
MALAYSIA
1800-22-8899 (HHP)
1800-88-9999 (OTH)
[phone]
(Overseas contact)
www.samsung.com/my/support
Country/Area Samsung Service Centre Web Site
INDONESIA
021-5699-7777
0800-112-8888
(All Product, Toll Free)
0800-112-7777
(All Product, Toll Free)
www.samsung.com/id/support
PHILIPPINES
Dedicated Hotline for Mobile
Phones:
#GALAXY (just dial #425299)
All Products :
1-800-10-7267864
[ PLDT - Toll Free ]
1-800-8-7267864
[ Globe - Toll Free ]
84222111 [ Landline ]
www.samsung.com/ph/support
INDIA
1800 5 SAMSUNG
(1800 5 7267864) (Toll-Free)
1800 40 SAMSUNG
(1800 40 7267864) (Toll-Free)
www.samsung.com/in/support
NEPAL
16600172667
(Toll Free for NTC Only)
www.samsung.com/in/
support
9801572667
(Toll Free for Ncell users)
SRI LANKA 011 SAMSUNG (011 7267864)
BANGLADESH 08000-300-300 (Toll free)
09612-300-300 www.samsung.com/bd/support

English
User Manual
VA81-01146Q-00
NSPBI01285A-00
SWA-9200S
© 2022 Samsung Electronics Co., Ltd. All rights reserved.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care Centre.
SAFETY INFORMATION
Thank you for purchasing this
product (SWA-9200S).
CAUTION
RISK OF ELECTRIC SHOCK. DO NOT
OPEN.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER (OR BACK). NO USER-
SERVICEABLE PARTS ARE INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL. Refer to the table
below for an explanation of symbols which may be on
your Samsung product.
This symbol indicates that high voltage is
present inside. It is dangerous to make any
kind of contact with any internal part of this
product.
This symbol indicates that this product has
included important literature concerning
operation and maintenance.
Class II product : This symbol indicates that
it does not require a safety connection to
electrical earth (ground).
If this symbol is not present on a product
with a power cord, the product MUST have
a reliable connection to protective earth
(ground).
AC voltage : This symbol indicates that the
rated voltage marked with the symbol is AC
voltage.
DC voltage : This symbol indicates that the
rated voltage marked with the symbol is DC
voltage.
Caution, Consult instructions for use : This
symbol instructs the user to consult the user
manual for further safety related information.
• The slots and openings in the cabinet and in the back or
bottom are provided for necessary ventilation. To ensure
reliable operation of this apparatus, and to protect it
from overheating, these slots and openings must never
be blocked or covered.
‒ Donotplacethisapparatusinaconnedspace,
such as a bookcase, or built-in cabinet, unless proper
ventilation is provided.
‒ Do not place this apparatus near or over a radiator
or heat register, or where it is exposed to direct
sunlight.
‒ Do not place vessels (vases etc.) containing water
onthisapparatus.Awaterspillcancauseareor
electric shock.
• Do not expose this apparatus to rain or place it near
water (near a bathtub, washbowl, kitchen sink, or
laundry tub, in a wet basement, or near a swimming
pool, etc.). If this apparatus accidentally gets wet,
unplug it and contact an authorized dealer immediately.
• Do not overload wall outlets, extension cords or
adaptors beyond their capacity, since this can result in
reorelectricshock.
• Route power-supply cords so that they are not likely to
be walked on or pinched by items placed on or against
them. Pay particular attention to cords at the plug end,
at wall outlets, and the point where they exit from the
apparatus.
• To protect this apparatus from a lightning storm, or
when it is left unattended and unused for long periods
of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage
to the set due to lightning and power line surges.
• Before connecting the AC power cord to the DC adaptor
outlet, make sure the voltage designation of the DC
adaptor corresponds to the local electrical supply.
• Never insert anything metallic into the open parts of
this apparatus. Doing so may create a danger of electric
shock.
• To avoid electric shock, never touch the inside of this
apparatus.Onlyaqualiedtechnicianshouldopenthis
apparatus.
• Makesuretoplugthepowercordinuntilitisrmly
seated. When unplugging the power cord from a wall
outlet, always pull on the power cord’s plug. Never
unplug by pulling on the power cord. Do not touch the
power cord with wet hands.
• If this apparatus does not operate normally - in
particular, if there are any unusual sounds or smells
coming from it - unplug it immediately and contact an
authorized dealer or service centre.
• Maintenance of Cabinet.
‒ Before connecting other components to this product,
be sure to turn them off.
• Be sure to pull the power plug out of the outlet if the
product is to remain unused or if you are leaving the
house for an extended period of time (especially when
children, elderly, or disabled people will be left alone in
the house).
‒ Accumulated dust can cause an electric shock, an
electricleakage,orarebycausingthepowercord
to generate sparks and heat or the insulation to
deteriorate.
• Contact an authorized service centre for information
if you intend to install your product in a location with
heavy dust, high or low temperatures, high humidity,
chemical substances, or where it will operate 24 hours
a day such as in an airport, a train station, etc. Failing to
do so may cause serious damage to your product.
• Use only a properly grounded plug and wall outlet.
‒ An improper ground may cause electric shock or
equipment damage. (Class l Equipment only.)
• To turn this apparatus off completely, you must
disconnect it from the wall outlet. Consequently, the
wall outlet and power plug must be readily accessible
at all times.
• Do not allow children to hang on the product.
• Store the accessories (battery, etc.) in a location safely
out of the reach of children.
• Do not install the product in an unstable location such
asashakyself,aslantedoor,oralocationexposedto
vibration.
• Do not drop or strike the product. If the product is
damaged, disconnect the power cord and contact a
service centre.
• To clean this apparatus, unplug the power cord from
the wall outlet, and then wipe the product using a
soft, dry cloth. Do not use any chemicals such as wax,
benzene, alcohol, thinners, insecticide, air fresheners,
lubricants, or detergent. These chemicals can damage
the appearance of the product or erase the printing on
the product.
• Do not expose this apparatus to dripping or splashing.
Donotputobjectslledwithliquids,suchasvases,on
the apparatus.
• Do not plug multiple electric devices into the same wall
socket. Overloading a socket can cause it to overheat,
resultinginare.
WARNING
• TO PREVENT THE SPREAD OF FIRE,
KEEP CANDLES AND OTHER ITEMS WITH
OPEN FLAMES AWAY FROM
THIS PRODUCT AT ALL TIMES.
• Toreducetheriskofreorelectricshock,donotexpose
this appliance to rain or moisture.
Precautions
1. Ensure that the AC or DC power supply in your house
complies with the power requirements listed on the
identicationstickerlocatedontherearofyourproduct.
Install your product horizontally, on a suitable base
(furniture), with enough space around it forventilation
(7~10 cm). Make sure the ventilation slots are not
covered.Donotplacetheunitonampliersorother
equipment which may become hot. This unit is designed
for continuous use. To fully turn off the unit, disconnect
the AC plug from the wall outlet.
2. Do not expose the unit to direct sunlight or other heat
sources. This could lead to overheating and cause the
unit to malfunction.
3. Unplug the Power cord from the AC wall socket if the
unit malfunctions. Your product is not intended for
industrial use. It is for personal use only. Condensation
may occur if your product has been stored in cold
temperatures. If transporting the unit during the winter,
wait approximately 2 hours until the unit has reached
room temperature before using it.
4. If the electricity supplied to your home is rated at 240V
AC, use a suitable plug adapter to connect this unit to
your electrical outlets.
Important Safety Instructions
Read these operating instructions carefully before using
the unit. Follow all the safety instructions listed below.
Keep these operating instructions handy for future
reference.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including AV
receivers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided foryour safety. If
theprovidedplugdoesnottintoyouroutlet,consult
an electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where it exits the apparatus.
11. Onlyuseattachments/accessoriesspeciedbythe
manufacturer.
12. Use only with the cart, stand, tripod,
bracket,ortablespeciedbythe
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
you intend to leave it unused for long periods of time.
14. Referallservicingtoqualiedservicepersonnel.
Servicing is required when the apparatus has been
damaged in any way, such as when the power-supply
cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
01 CHECKING THE
COMPONENTS
Surround Speaker X 2 / Speaker Cable / AC/DC Adapter
/ Power Cord
NOTE
• For more information about the power supply and
power consumption, refer to the label attached to the
product. (Label: Rear of the Main Unit)
• Designandspecicationsaresubjecttochangewithout
prior notice.
02 CONNECTING THE
SWA-9200S TO A
SOUNDBAR
1. Connect the Surround speaker cables
Use the speaker cables to connect the two surround sound
speakers.
• When connecting the speaker cable, connect the core
wire to the speaker.
• Insert the wire fully, taking care not to insert beyond
the wire insulation.
Insert the wire fully.
+ : Red
- : Black
• When connecting the speaker cables to the surround
speakers, follow these steps:
‒ Insert the red and black colored ends of each
speaker cable into the red and black jacks of the
appropriate speaker.
‒ The labels are on the backs of the speakers.
Audio cable
‒ The length of the speaker audio cable: 6 m
2. Turn on the Surround speakers
Plug the Surround speakers’ power cord into an electrical
outlet to turn on the Surround speakers. The LINK LED
indicator(blue LED) on the rear of left surround speaker will
blink quickly.
If the LINK LED does not blink, please see step 6.
LINK STANDBY
ID SET
Rear of Left
Surround
LINK STANDBY
ID SET
LINK STANDBY
ID SET
Rear of Left Surround
"Blue
blinking"
3. Turn off the Soundbar
If the Soundbar is turned on, please turn off the Soundbar
by pressing the (Power) button on the Soundbar or
remote control.
SOUND
MODE
PAIR
BYE
OR
Red BlinksX3
• The image of the Soundbar may differ from your
Soundbar, depending on the model.
4. Connect Soundbar and Surround Speakers
Press the Up button on the remote control for more than
5 seconds until the “ID SET” message appears on the
Soundbar’s display. The message will disappear shortly.
(If your Soundbar does not have a display window and only
LED indicators, please refer to the LED information below.)
• After the ID SET process is successful, the Soundbar will
turn on automatically.
OR
SOUND
MODE
PAIR
5 sec
ID SET
Red → Green →
Blue Blinks
• The image of the Soundbar may differ from your
Soundbar, depending on the model.
5. Check the connection complete
The LINK LED stops blinking and changes to solid blue
when the Soundbar and surround speakers are successfully
linked.
PleaseturnofftheSoundbarandturnitbackon.Conrm
that the LINK LED is blue.
(It may take a minute depending on the environment.)
LINK STANDBY
ID SET
LINK STANDBY
ID SET
Rear of Left Surround
“Blue is On”
• If the LINK LED does not turn to solid blue in a minute,
please repeat from step 2 through 5 referring to step 6
(LED indicator’s status).
6. LED Indicator’s status
LINK (Blue) On : Connected with the Soundbar.
LINK (Blue) Blinking fast (at an interval of around
0.5 second) : Surround speakers are in ID SET mode.
• Check if the Soundbar is turned on and in ID SET
mode.
• Repeat steps 3 through 5.
LINK (Blue) Blinking slow (at an interval of around
1 second) : Previously connected to a Soundbar but
cannotcurrentlyndit.
• Check if the Soundbar is turned on.
• If the LINK LED keeps blinking slowly even when the
Soundbar is turned on,
1. Press the ID SET button on the rear of the left
surround for more than 5 seconds until the LINK
LED starts blinking fast in blue.
LINK STANDBY
ID SET
LINK STANDBY
ID SET
5 sec
Rear of Left Surround
2. Repeat steps 3 through 5.
STANDBY (Red) On : When the Soundbar turns off or
connection has failed.
• Follow the instructions for “Link (Blue) Blinking slow
(at an interval of around 1 second)” above.
Others : Errors
• Contact a Samsung Service Centre.
03 TROUBLE SHOOTING
There is no sound from Surround Speakers
• If the Surround speakers are successfully paired and
connected to a Soundbar, the LINK LED indicator on
the rear of the Left Surround is on and solid blue.
Please reconnect the Surround speakers to your
Soundbar referring to 02-6, LED Indicator’s status.
• Other devices sending radio frequency signals in
proximity may interrupt the connection. Please keep
your speaker away from such devices.
• The content you are playing may have no surround
track but only stereo. Please change the sound mode
to Surround by pressing SOUND MODE button on the
remote control.
There is sound jitter, delays, noise or dropout from the
sound of Surround Speakers.
• There may be sound jitter or delays when the Surround
Speakers are far from the Soundbar. Please place
them near the Soundbar.
• There may be sound jitter or delays when the
Soundbar is near an electrical device that can cause
radio interference. Please place the Soundbar far from
such devices that can cause radio interference
(e.g. wireless router).
• Please change the TV network connection status from
wireless to wired.
The volume of Surround Speakers is too low
• Please increase the rear level referring to the manual
of your Soundbar.
(You can download the manual of your Soundbar from
www.samsung.com/support)
04 MOUNTING ON A WALL
LINK STANDBY
8.2 mm
4.2 mm
7.9 mm
4.6 mm
4.0 mm
• Be sure the wall is stable. If the wall is weak, reinforce
it before installation.
• Take care not to install the speakers sideways or upside
down.
• Samsung Electronics is not liable for any damage to the
product due to improper installation.
• Wall mounts aren’t sold by Samsung Electronics.
05 COMPATIBLE MODELS
• Compatible with select Samsung Soundbar. Please visit
the Soundbar product page at www.samsung.com/
support for more information.
• Compatible model list is subject to change without
further notice.
06 OPEN SOURCE LICENSE
NOTICE
To send inquiries and requests for questions regarding
open sources, contact Samsung Open Source
(http://opensource.samsung.com)
07 SPECIFICATIONS AND
GUIDE
Specications
Subwoofer Name
SWA-9200S (LEFT/RIGHT)
Weight
1.7 kg
Dimensions (W x H x D)
105.0 x 152.8 x 109.0 mm
Operating Temperature
Range
10℃to40℃
Operating Humidity Range
10 % ~ 80 %,
non-condensing
AMPLIFIER
Rated Output power
60 W x 2
NOTE
• Samsung Electronics Co., Ltd reserves the right to
changethespecicationswithoutnotice.
• Weight and dimensions are approximate.
Country/Area Samsung Service Centre Web Site
CHINA 400-810-5858 www.samsung.com/cn/support
TAIWAN
0800-32-9999 (All Product)
0809-05-5237 (Only for HHP)
0809-00-5237 (B2B / Dealer)
0809-02-6868 (Samsung pay)
www.samsung.com/tw/support
HONG KONG
3698 4698 ( All Product)
3698 4688 ( B2B )
3698 4633 (eStore)
2121 9088 ( Samsung pay )
www.samsung.com/hk/support
(Chinese)
www.samsung.com/hk_en/
support (English)
MACAU 0800 333
SINGAPORE
1800 7267864 |
1800-SAMSUNG (Other)
1800 4252997 |
1800-GALAXYS (HHP)
www.samsung.com/sg/support
AUSTRALIA 1300 362 603 (Other)
1300 425 299 (HHP) www.samsung.com/au/support
NEW ZEALAND
0800 726 786 (All Product)
0800 6 726 786 (Support for
Smart Mobile Devices)
www.samsung.com/nz/support
VIETNAM 1800 588 889 (All Product)
1800-588-855 (HHP) www.samsung.com/vn/support
THAILAND
Hotline no : 1282
1800-29-3232
(Toll free for all product)
www.samsung.com/th/support
MYANMAR [phone]
VIP HHP [phone]
www.samsung.com/mm/
support
CAMBODIA 1800-20-3232 (Toll free) www.samsung.com/th/support
LAOS [phone]
MALAYSIA
1800-22-8899 (HHP)
1800-88-9999 (OTH)
[phone]
(Overseas contact)
www.samsung.com/my/support
Country/Area Samsung Service Centre Web Site
INDONESIA
021-5699-7777
0800-112-8888
(All Product, Toll Free)
0800-112-7777
(All Product, Toll Free)
www.samsung.com/id/support
PHILIPPINES
Dedicated Hotline for Mobile
Phones:
#GALAXY (just dial #425299)
All Products :
1-800-10-7267864
[ PLDT - Toll Free ]
1-800-8-7267864
[ Globe - Toll Free ]
84222111 [ Landline ]
www.samsung.com/ph/support
INDIA
1800 5 SAMSUNG
(1800 5 7267864) (Toll-Free)
1800 40 SAMSUNG
(1800 40 7267864) (Toll-Free)
www.samsung.com/in/support
NEPAL
16600172667
(Toll Free for NTC Only)
www.samsung.com/in/
support
9801572667
(Toll Free for Ncell users)
SRI LANKA 011 SAMSUNG (011 7267864)
BANGLADESH 08000-300-300 (Toll free)
09612-300-300 www.samsung.com/bd/support