Samsung CS29Z47 User manual

English - 1
Connection Panel (depending on the model)
Rear Panel
Owner’s Instructions
Before operating, please read this manual thoroughly,
and retain it for future reference.
Register your product at
www.samsung.com/global/register
➢The actual configuration of your TV may be different,
depending on your model.
Control Panel (depending on the model)
You can use the 3buttons to switch the TV on when it is
in standby mode.
The 2and 3buttons also have the same function as
the ◄/►/▲/▼ buttons on the remote control.
If the remote control no longer works or you have
misplaced it, you can use the controls on the panel of the
television.
Front (or Side) Panel
1On-screen menu display
2Volume adjustment
3Channel selection
4Remote control sensor
5Standby indicator
6Power on/off
AA68-04048J-00
AA68-04048J
➢The actual configuration of your TV may be different,
depending on your model.
Connecting to the RCA Input
The RCA3and RCA4connectors are used for equipment,
such as a VCR, DVD, decoder, satellite receiver, video
game device, or video disc player. (When using the mono
equipment, connect to the AUDIO-L input connector.)
The RCA5connectors are used for equipment such as a
DVD with component output.
cable television
network
or
cable television
network
or
COLOR TELEVISION
CS29Z45 / CS29Z47 / CS29Z50 / CS29Z57
CS29Z58 / CS29A730 / CS29A760 /
CS29A750 / CS29B850 / CS29U50 /
CS29U57
☛
Whenever you connect an audio or video system to your
television, ensure that all elements are switched off.
Please be sure to match the color coded input terminals
and cable jacks.
Connecting to an Aerial or Cable Television Network
Connect the aerial or network input cable to the 1 (75 Ω
coaxial socket).
To view television channels correctly, a signal must be
received by the set from one of the sources: an outdoor
aerial, cable television network, or satellite network.
If you are using an indoor aerial, you may need to adjust it
when tuning your television until you obtain a picture that is
both sharp and clear.
Connecting to the RCA Output
The RCA2connectors are used for equipment, such as a
recording VCR or audio system.
☛
Please be sure to match the color coded input terminals
and cable jacks.
Connecting to the RCA Input
The 2(AUDIO-L/R) and 1(VIDEO) connectors are used
for equipment, such as a camcorder, video disc player, or
video game device.
➢When both the front (or side) AV and rear connectors (AV
IN2) are connected to external equipment, the front (or
side) AV receives priority.
1 Video input
2 Audio input
Front (or Side) Panel
OU T
VI DEO
IN 2
IN 1
Y
P B
P R
AA68-04048J-Eng.indd 1 2009-12-07 �� 6:29:47

English - 2
The mains lead is attached to the rear of the television.
1 Plug the mains lead into an appropriate socket.
➢The main voltage is indicated on the rear of the
television and the frequency is 50 or 60Hz.
2 Press the “P” button (On/Off) CH</>button on the
front (or side) of the television.
3 Press the POWER button on the remote control to
switch the television on. The programme that you were
watching last is re-selected automatically. If you have
not yet stored any channels, no clear picture appears.
Refer to “Channel - Auto Store” on page 3 or “Channel -
Manual Store” on page 3.
➢If the television is initially powered on, several basic
customer settings proceed automatically. Refer to
“Setup - Plug & Play” on page 3.
4 Press the P</>button, or Numeric button on the
remote control.
➢Caution: One pole switch is totally not off (one line still
live) if power cord is not unplugged.
Switching the Television On and Off
The television can be placed in standby mode, in order to
reduce power consumption and wear of the cathode ray
tube. Standby mode can be useful when you wish to interrupt
viewing temporarily (during a meal, for example).
1 Press the POWER button on the remote control while
viewing.
2 To switch the television back on, simply press it again.
☛
Do not leave the television in standby mode for long
periods of time (when you are away on holiday, for
example).
It is best to unplug the set from the mains and aerial.
Placing the Television in Standby Mode
Remote Control
(depending on the model)
➢Operation of remote control may be affected by bright
artificial light near to the TV.
Installing Batteries
Remove the cover. Install two AAA size
batteries, then replace the cover.
When the remote control does not
operate normally, check that the “+” and
“-” ends of the batteries are inserted correctly or the batteries
are drained.
➢Do not mix battery types, i.e. alkaline and manganese.
1POWER
Used to switch the TV
on and off.
2MENU
Used to display the
on-screen menu or
return to the previous
menu.
3▲/▼/◄/►
Used to control the
cursor in the menu.
P </ >
Used to display the
next or previous stored
channel
=+ / -
Used to increase or
decrease the volume.
4MUTE
Used to switch the
sound off temporarily.
To turn the sound back
on, press the MUTE,
=+ or =- button.
5Numeric buttons
Used to select channels
directly.
6INFO
Used to view the
channel information
and setting status you
selected.
7 SOURCE
Used to display all of
the available video
sources.
8 TOOLS (depending on
the model)
You can check the
following selection by
pressing Tools button.
1. Sleep Timer(Used to
select a preset time
interval for automatic
turn off.)
2. Picture Mode(Used
to select the picture
effect.)
3. Sound Mode(Used
to select sound
effect.)
4. Dual I-II(Used to
select sound mode.)
5. Turbo Plus(Used to
select the Turbo Plus
option.)
6. Sound Adjust (Used
to display the sound
menu)
9ENTER
While using the
on-screen menus,
press the ENTER
button to activate (or
change) a particular
item.
0EXIT
Used to exit from any
display or return to
normal viewing.
! PRE-CH
Used to switch
repeatedly between
the last two channels
displayed.
AA68-04048J-Eng.indd 2 2009-12-07 �� 6:29:47

English - 3
◆ Source List
You can switch between
viewing signal from
connected equipment,
such as a VCR, DVD, set-
top box, and the TV source
(broadcast or cable).
➢You can change the required external source simply
by pressing the SOURCE button on the remote
control. It might take a short period of time for
pictures to be switched. To return to the TV mode,
press the SOURCE button on the remote control.
Input - Source List (depending on the model)
Viewing the Menus
1 Press the MENU button.
The main menu is displayed on the screen. Its left side
has five icons: Input, Picture, Sound, Channel, and
Setup.
2 Press the ▲ or ▼ button to select one of the icons.
Press the ENTER button to access the icon’s sub-menu.
3 Press the ▲ or ▼ button to move to items in the menu.
Press the ENTER button to enter items in the menu.
4 Press the ▲/▼/◄/► button to change the selected
items. Press the MENU button to return to the previous
menu.
5 Press the EXIT button to exit from the menu.
Setup - Plug & Play (depending on the model)
When the television is initially powered on, several basic
customer settings proceed automatically and subsequently.
The following settings are available.
1 If the television is in standby
mode, press the POWER
button on the remote control.
The Start Plug & Play is
displayed. To start Plug
& Play, press the ENTER
button. The Language
menu is displayed.
➢The Language menu
will automatically appear
after several seconds,
even if the ENTER
button is not pressed.
2 Select the appropriated
language by pressing the
▲ or ▼ button. Press the
ENTER button. The Check
antenna input. is displayed.
➢If any language is not selected, the language menu
will disappear about 30 seconds later.
continued...
You can scan for the frequency ranges available to you (and
availability depends on your country). Automatically allocated
programme numbers may not correspond to actual or desired
programme numbers. However you can sort numbers
manually and clear any channels you do not wish to watch.
➢To stop the search before it has finished, press the
ENTER button.
When finished, the Sort menu
is displayed. To sort the stored
channels into the desired
numerical order, refer to
“Channel - Sort”. To exit without
sorting, press the EXIT button.
Channel - Auto Store
3 To search the channels,
press the ENTER button. To
stop the search, press the
ENTER button.
When the channel searching
has finished, the Clock Set
menu is displayed.
4 Press the ◄ or ► button to
move to the hour or minute.
Set the hour or minute by
pressing the ▲ or ▼ button.
5 When you have finished,
press the MENU button.
The Enjoy your watching.
is displayed, and then the
channel which has been
stored will be activated.
Re-setting the Plug & Play
Method:
MENU ➜▲/▼ (Setup) ➜
ENTER ➜▲/▼ (Plug & Play)
➜ENTER
This operation allows you to
change the programme numbers
of stored channels. This
operation may be necessary
after using auto store.
◆ From: Channel number to
be changed.
◆ To: New channel number to be identified.
◆ Store: Confirmation the exchange of channel numbers.
Channel - Sort
Plug & Play
Enter Skip
OK
Check antenna input.
OK
Enjoy your watching.
Move Enter
Adjust Skip
Plug & Play
Clock Set 12:00 am
Move Enter Return
TV
Plug & Play 
Language : English 
Time 
Child Lock 
Blue Screen : On 
Setup
Auto Store
P 1 102MHz
7 %
Enter Skip
Plug & Play
Stop
Plug & Play
Enter Skip
Auto Store
Start
Plug & Play
Enter Exit
OK
Start Plug & Play.
Plug & Play
Move Enter Skip
Language
English
Indonesia
Melayu
TV
AV1
AV2
Component
Move Enter Return
TV Source List
Search
Enter Return
Stop
P 1 102MHz
7 %
From : P 1
To : P--
Store : ?
Move Adjust Return
Sort
TV
AA68-04048J-Eng.indd 3 2009-12-07 �� 6:29:48

English - 4
Setup - Time
Clock
You can set the television
clock so that the current time
is displayed when pressing
the INFO button on the
remote control. You must
also set the time if you wish
to use the automatic on or
off timers.
➢When pressing the " P" button (On/Off) on the front
(or side) of the television, the clock setting will be
reset.
On Timer / Off Timer
You can set the On/Off timers so that the television will
switch on or off automatically at the time you select.
☛You must set the clock first.
☛Auto Power Off
When you set the timer “On”, the TV will eventually turn
off, if no controls are operated for 3 hours after the TV
was turned on by timer. This function is only available in
timer “On” mode and prevents overheating, which may
occur if a TV is on for too long.
You can exclude channels you
have chosen from the channels
you scanned. When you scan
through the stored channels,
those you have chosen to
skip are not displayed. All of
the channels that you did not
specifically choose to skip are
displayed during scanning.
Method:
ENTER : Select Added or Deleted.
Channel - Add/Delete
◆Programme (Programme number to be assigned to a
channel)
◆Color System: AUTO/PAL/SECAM/NTSC4.43/
NTSC3.58
◆Sound System: BG/DK/I/M
◆Search (When you do not know the channel numbers):
The tuner scans the frequency range until the first
channel or the channel that you selected is received on
the screen.
➢You can also select the channel number directly by
pressing the numeric buttons (0-9).
◆ Store (When you store the channel and associated
programme number)
➢If there is no sound or abnormal sound, re-select the
sound standard required.
If the reception is clear, you do not have to fine-tune the
channel, as this is done automatically during the search and
store operation. If however the signal is weak or distorted,
you may have to fine-tune the channel manually.
Method:
◄/►: You can obtain a sharp
and clear picture and good
sound quality.
▲/▼ ➜ENTER : You can reset
the setting.
ENTER : You can memorise
adjusted picture or sound.
Channel - Fine Tune
Move Enter Return
Time
TV
Clock 1 2 : 0 0 am
On Timer --:-- am Off
Off Timer --:-- am Off
Channel - Manual Store
You can store channels,
including those received via
cable networks. When storing
channels manually, you can
choose:
- Whether or not to store each
of the channels found.
- The programme number of
each stored channel which you wish to identify.
Programme : P 3
Color System : AUTO 
Sound System : BG 
Search : 46MHz
Store : ?
Move Adjust Return
TV Manual Store
More
P 1 : Added
P 2 : Added
P 3 : Added
P 4 : Added
P 5 : Added
More
Move Enter Return
Add/Delete
TV
Fine Tune
Move Save
Adjust Return
Reset
P 1 0
AA68-04048J-Eng.indd 4 2009-12-07 �� 6:29:48

English - 5
◆ Language
It is variable depending on
the model. When you start
using the television for the
first time, you must select
the language which will be
used for displaying menus
and indications.
◆ Blue Screen
If no signal is being received or the signal is very weak,
a blue screen automatically replaces the noisy picture
background. If you wish to continue viewing the poor
picture, you must set the Blue Screen to Off.
Setup -
Language / Blue Screen (depending on the model)
This feature allows you to
prevent unauthorized users,
such as children, from watching
unsuitable programmes by
muting out video and audio.
Child Lock cannot be released
using front (or side) panel
buttons. Only remote control can
release the Child Lock setting, so keep the remote control
away from children.
◆ Child Lock: On/Off
If you want to unlock a channel, set to Off.
◆ Programme: Channel number to be locked.
◆ Lock: When press the ENTER button, the Locked is
displayed.
➢If any channel is locked, you can not access to the
Channel and Child Lock menu by using the control
buttons on the TV panel (the Not available is displayed
in the Child Lock menu). You can access by using the
remote control only.
Setup - Child Lock
◆ Mode: Dynamic/ Standard/
Movie/Custom
You can select the type
of picture which best
corresponds to your viewing
requirements.
➢
You can select these
options simply by pressing the TOOLS button on the
remote control and enter the Picture Mode.
◆ Contrast/Brightness/Sharpness/Color/
Tint(NTSC only)
The television has several settings which allow you to
control the picture quality.
◆ Color Tone: Cool2/Cool1/Normal/Warm1/ Warm2
◆ Reset
You can return to the factory defaults.
The reset function is set for each mode (Dynamic,
Standard, Movie, or Custom).
Picture - Mode
Picture - Digital NR / DNIe
(depending on the model)
◆ Digital NR
If the signal received by
the television is weak, you
can activate this feature
to reduce any static and
ghosting that may appear
on the screen.
◆ DNIe
This feature bring you more detailed image with detail
enhancement, contrast enhancement and white
enhancement. New image compensation algorithm
gives brighter, clearer, much detailed image to you. DNIe
technology will fit every signals into your eyes.
◆ Size: Normal/Zoom
You can select the picture size which best corresponds
to your viewing requirements. It is variable depending on
the model.
Method:
◄/►: Select Normal or Zoom.
Picture - Size (depending on the model)
Sleep Timer
You can select a time period of between 30 and 180 minutes
after which the television automatically switches to standby
mode.
You can select these options simply by pressing the TOOLS
button on the remote control to enter Sleep Timer.
If the sleep timer is not yet set, Off is displayed. If it is already
set, the remaining time before which the television switches to
standby mode is displayed.
Child Lock : On 
Programme : P 1
Lock : ?
Move Enter Return
Child Lock
TV
Move Adjust Return
Mode
TV
Mode : Dynamic 
Contrast : 100
Brightness : 50
Sharpness : 75
Color : 50
Tint : G 50 R 50
Color Tone : Cool1 
Reset 
Move Enter Exit
Picture
TV
Mode : Dynamic 
Size : Normal 
Digital NR : Off 
DNIe : Off 
Plug & Play 
Language : English 
Time 
Child Lock 
Blue Screen : On 
Move Enter Exit
Setup
TV
Move
Adjust
Return
Picture
TV
Mode : Dynamic 
Size : Normal 
Digital NR : Off 
DNIe : Off 
AA68-04048J-Eng.indd 5 2009-12-07 �� 6:29:48