Samsung SP-43R1HL User manual

Infrared Remote Control
➢The performance of the remote control may be affected by bright light.
DIRECT CHANNEL SELECTION
MENU DISPLAY/
TELETEXT INDEX
CONTROL THE CURSOR
IN THE ON-SCREEN MENU
SURROUND ON/OFF DIRECTLY
TELEVISION STANDBY
FASTEXT TOPIC SELECTION
AUTOMATIC SWITCH-OFF
TELETEXT PAGE HOLD
INFORMATION DISPLAY/
TELETEXT REVEAL
EXIT FROM ANY DISPLAY
ONE OR TWO-DIGIT CHANNEL
SELECTION/
TELETEXT STORE
SELF FOCUS
PICTURE FREEZE
TELETEXT SUB-PAGE
TELETEXT CANCEL
EXTERNAL INPUT SELECTION/
TELETEXT MODE (LIST/FLOF)
SELECTION
SWITCH REPEATEDLY BETWEEN THE
LAST TWO CHANNELS DISPLAYED
CONFIRM YOUR CHOICE
(STORE OR ENTER)
NEXT CHANNEL/
TELETEXT NEXT PAGE
PICTURE EFFECT SELECTION
IF YOUR REMOTE CONTROL IS
NOT FUNCTIONING PROPERLY,
TAKE OUT THE BATTERIES AND
PRESS THE RESET BUTTON FOR
ABOUT 2~3 SECONDS. RE-INSERT
THE BATTERIES AND TRY USING
THE REMOTE CONTROL AGAIN.
SOUND MODE SELECTION
PREVIOUS CHANNEL/
TELETEXT PREVIOUS PAGE
MAKE THE REMOTE CONTROL WORKS
FOR TV, STB, VCR, CABLE, DVD
PLAYER
TUNER/CABLE NETWORK
SELECTION
VOLUME INCREASE
TEMPORARY SOUND SWITCH-OFF
VOLUME DECREASE
TELETEXT DISPLAY/
MIX BOTH TELETEXT INFORMATION
AND THE NORMAL BROADCAST
SOUND EFFECT SELECTIOND
PICTURE SIZE/
TELETEXT SIZE SELECTION
VCR/DVD FUNCTIONS;
-REWIND ( )
-STOP ( )
-PLAY/PAUSE ( )
-FAST FORWARD ( )
REMOTE CONTROL SETUP
BP68-00457A-01(J60B_Euro_ENG) 2005/01/13 02:10 PM Page 10

Connecting a Satellite Receiver or Decoder
In order to watch television programmes broadcast via a
satellite network, you must connect a satellite receiver to
the rear of TV. Also, in order to descramble a coded
transmission signal, you must connect a decoder to the
rear of TV.
◆Using a SCART cable
Connect the receiver (or decoder) SCART cable to one
of the SCART connectors on the rear of the television.
◆Using a coaxial cable
Connect a coaxial cable to the:
- Receiver (or Decoder) output socket.
- Television aerial input socket.
➢If you wish to connect both a satellite receiver
(or decoder) and a VCR, you should connect the:
◆Receiver (or Decoder) to the VCR
◆VCR to the television
Otherwise, connect the receiver (or decoder) directly
to the television.
Rear of the TV
Satellite receiver/
Decoder
BP68-00457A-01(J60B_Euro_ENG) 2005/01/13 02:10 PM Page 12

Connecting to the External Input/Outputs
➢ EXT 1 is used for the equipment with an RGB output, such as video game
devices or video disc players.
Rear of the TV
VCR
Decoder /
Video game device
Video disc player
Satellite receiver
① This end can be fitted with:
◆A SCART connector
◆An S-Video connector and two audio RCA connectors (L+R); EXT 2
◆Three RCA connectors (VIDEO + AUDIO-L and R)
② If you have a second VCR and wish to copy cassette tape, connect the
source VCR to EXT 1 and the target VCR to EXT 2 so that you can redirect
the signal from EXT 1 to EXT 2.
③ If you have a decoder, connect the decoder to the VCR and the VCR to the
television.
➃ When you wish to record a programme, connect the receiver to EXT 1 and
the VCR to EXT 2 so that you can redirect the signal from EXT 1 to EXT 2.
or
or
①
DVD
②
➃
③
☛Whenever you connect an audio or video system to your
television, ensure that all elements are switched off.
Refer to the documentation supplied with your equipment
for detailed connection instructions and associated safety
precautions.
BP68-00457A-01(J60B_Euro_ENG) 2005/01/13 02:11 PM Page 53

Connecting to the Audio Output
➢The RCA (AUDIO-L and R) connectors are used for equipment, such as an audio
system (to take full advantage of the Surround sound effect).
Rear of the TV
Audio system
BP68-00457A-01(J60B_Euro_ENG) 2005/01/13 02:11 PM Page 54

Connecting to the RCA Input
➢The RCA (VIDEO + AUDIO-L and R) connectors are used for the equipment, such as camcorders,
video disc players, and some video game devices.
Side of the TV
(depending on the model)
Camcorder
Video game device
Video disc player
BP68-00457A-01(J60B_Euro_ENG) 2005/01/13 02:11 PM Page 55