Samsung SP42L6HX - 42" Rear Projection TV User manual

DLP TV
SP42L6HX
SP46L6HX
SP50L6HX
SP56K3HX
SP61K3HX
SP61L6HX
SP67L6HX
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
Picture In Picture (PIP)
My Colour Control
SRS TruSurroundXT
Digital Natural Image engine
This device is a Class B digital apparatus.
Register your product at www.samsung.com/global/register
BP68-00613A-00Eng 5/17/06 1:25 PM Page 1

©2006 Samsung Electronics Co., Ltd. All rights reserved.
BP68-00613A-00Eng 5/17/06 4:15 PM Page 2

English - 3
continued...
Contents
◆CONNECTING AND PREPARING YOUR TELEVISION
■Checking Parts .............................................................................................. 5
■Control Panel................................................................................................. 6
■Connection Panel .......................................................................................... 8
■Infrared Remote Control ................................................................................ 11
■Inserting the Batteries in the Remote Control................................................ 12
■Connecting to an Aerial or Cable Television Network ................................... 13
■Connecting a Satellite Receiver or Decoder.................................................. 13
■Switching Your Television On and Off........................................................... 14
■Placing Your Television in Standby Mode..................................................... 14
■Becoming Familiar with the Remote Control ................................................. 15
■Plug & Play Feature....................................................................................... 16
■Choosing Your Language.............................................................................. 17
◆SETTING THE CHANNELS
■Storing Channels Automatically..................................................................... 18
■Storing Channels Manually............................................................................ 19
■Skipping Unwanted Channels ....................................................................... 21
■Sorting the Stored Channels ......................................................................... 22
■Assigning Names to Channels ...................................................................... 23
■Locking the Channel...................................................................................... 24
■Using the LNA (Low Noise Amplifier) Feature............................................... 25
■Fine Tuning Channel Reception.................................................................... 26
◆USING YOUR DISPLAY
■Displaying Information ................................................................................... 26
■Changing the Picture Standard ..................................................................... 27
■Customizing the Picture Settings................................................................... 28
■Setting the Picture (PC Mode)....................................................................... 29
■Selecting the Picture Size.............................................................................. 31
■Viewing the DNIe Demonstration .................................................................. 32
■Freezing the Current Picture ......................................................................... 32
■Setting the My Colour Control (Easy Control) ............................................... 33
■Setting the My Colour Control (Detail Control) .............................................. 34
■Setting the Blue Screen................................................................................. 35
■Activating Panel Button Lock......................................................................... 35
■Setting the Film Mode.................................................................................... 36
■Viewing the Picture in Picture (PIP)............................................................... 37
■Using the Digital NR (Noise Reduction) Feature ........................................... 40
■Changing the Sound Standard ...................................................................... 41
■Customizing the Sound Settings ................................................................... 42
■Setting the TruSurround XT........................................................................... 43
BP68-00613A-00Eng 5/17/06 1:25 PM Page 3

English - 4
➢
◆USING YOUR DISPLAY (continued)
■Adjusting the Volume Automatically .............................................................. 43
■Selecting the Internal Mute............................................................................ 44
■Setting the Melody Sound ............................................................................. 44
■Selecting the Sound Mode (depending on the model) .................................. 45
■Setting and Displaying the Current Time....................................................... 46
■Setting the Sleep Timer ................................................................................. 47
■Switching the Television On and Off Automatically ....................................... 48
■Viewing an External Signal Source ............................................................... 50
◆USING THE TELETEXT FEATURE
■Teletext Feature ............................................................................................ 51
■Displaying the Teletext Information ............................................................... 52
■Selecting Display Options.............................................................................. 53
■Selecting a Teletext Page.............................................................................. 54
◆ADDITIONAL INFORMATION AND CONNECTIONS
■Connecting to the External Devices .............................................................. 55
■Connecting to the RCA Input......................................................................... 56
■Connecting to the S-Video Input.................................................................... 56
■Connecting to the Component Input.............................................................. 57
■Connecting to the PC Input ........................................................................... 57
■Connecting to the HDMI (High Definition Multimedia Interface) Input ........... 58
■Connecting to the HDMI/DVI Compatible ...................................................... 58
■Connecting Home Theater System ............................................................... 59
■Setting up Your PC Software (Windows only) .............................................. 60
■PC Input Mode............................................................................................... 61
◆RECOMMENDATIONS FOR USE
■Setting Up Your Remote Control ................................................................... 62
■Remote Control Codes .................................................................................. 64
■Replacing the Lamp....................................................................................... 67
■Troubleshooting: Before Contacting Service Personnel................................ 68
■Technical Specifications ................................................................................ 69
☛➢
Press Important Note
Symbols
BP68-00613A-00Eng 5/17/06 1:25 PM Page 4

English - 5
Owner’s Instructions
Remote Control/
AAA Batteries
Replacement Lamp
For purchasing a replacement lamp,
ask at a nearby service center.
• Use authorized lamps only. The
company cannot guarantee the
quality of the product if an
unauthorized lamp is used.
Sold Separately
➢When installing the product, make sure to keep
it away from the wall (more than 10cm) for
ventilation purposes.
• Poor ventilation may cause an increase
in the internal temperature of the product,
resulting in a shortened component life
and degraded performance.
Checking Parts
Power Cord
Warranty Card/
Safety Guide Manual
(Not available in
all locations)
S-VIDEO Cable
PC Cable
HDMI Cable
HDMI/DVI Cable
PC Audio Cable
Component Cables
(RCA)
Antenna Cable
BP68-00613A-00Eng 5/17/06 1:25 PM Page 5

English - 6
Control Panel
➢
The actual configuration on your TV may be different, depending on
your model.
LED Indicators
Switch the TV On and Off
Picture On/Off
Remote Control Sensor
Switch among video input modes
Display the on-screen menu
Adjust the volume
Select the channels
Access to the selected option on
the menu system
Front of the TV
(SP42L6HX/SP46L6HX/SP50L6HX/SP61L6HX/SP67L6HX)
continued...
Picture On/Off
Remote Control
Sensor
Adjust the volume
Access to the selected option on
the menu system
Select the channels
Switch among video input modes
LED Indicators
Display the on-screen menu
Front of the TV
(SP56K3HX/SP61K3HX)
Switch the TV On and Off
(
➢
BP68-00613A-00Eng 5/17/06 1:25 PM Page 6

English - 7
n
s
(:On, :Blinking, :Off)
TIMER LAMP STAND BY/TEMP Indication
Standby mode.
A timer pilot lights when Timer Auto On or Off is selected.
Normal operation.
Normal operation (when Timer Auto On or Off is selected).
Lamp is warming up. The normal picture comes on after 25 seconds.
The normal picture comes on after 25 seconds. (when Timer Auto On or
Off is selected)
Air vent cover in the rear of the TV is not properly installed.
Inside temperature of the TV is over normal. Clean the air vent cover in the
rear of the TV. Turn the TV back on after 1 hour.
The lamp does not work, please contact an authorized Service Center for
assistance.
➢
◆ It takes about 30 seconds for the TV to warm up, so normal brightness may not appear
immediately.
◆ The TV has a fan to keep the inside lamp from overheating. You’ll occasionally hear it
working.
◆ You can use the channel selection buttons to switch on the TV when it is in standby mode
depending on the model.
◆ When using the on-screen menu the volume adjustment and channel selection buttons have
the same function as the …/†/œ/√buttons on the remote control.
◆ If the remote control no longer works or you have lost it, you can use controls on the panel
of the TV.
◆ Press the " I " side of the POWER switch to supply power to the TV. If the " I " side of the
POWER switch is not pressed, the POWER button on the remote control and the Picture
On/Off switch on the front panel of the TV will not work.
BP68-00613A-00Eng 5/17/06 1:25 PM Page 7

English - 8
Video Input Audio Input S-Video Input
Connection Panel
➢
The actual configuration on your TV may be different, depending on
your model.
Side of the TV
(SP42L6HX/SP46L6HX/SP50L6HX/SP61L6HX/SP67L6HX)
continued...
BP68-00613A-00Eng 5/17/06 1:25 PM Page 8

English - 9
n
Video Input
Audio Input
S-Video Input
Side of the TV
(SP56K3HX/SP61K3HX)
continued...
BP68-00613A-00Eng 5/17/06 1:47 PM Page 9

English - 10
Rear of the TV
a) ANT IN
Coaxial connector for Aerial/Cable Network.
b) S-VIDEO 1, 2
Video input for external devices with an S-Video
output, such as a camcorder or VCR.
c) AV IN 1, 2 (VIDEO / AUDIO L/R)
Video and audio inputs for external devices, such
as a camcorder or VCR.
d) AV OUT (VIDEO / AUDIO L/R)
Outputs for external devices.
e) COMPONENT IN 1, 2
Video (Y/PB/PR) and audio (AUDIO L/R) inputs for
Component.
f) PC IN (PC / AUDIO)
Connect to the video and audio output jack on
your PC.
g) DVI IN (AUDIO L/R)
DVI audio inputs for external devices.
h) HDMI/DVI IN
Connect to the HDMI jack of a device with
HDMI output. These inputs can also be used
as a DVI connection with separate analog
audio inputs. An optional HDMI/DVI cable
will be necessary to make this connection.
When using the optional HDMI/DVI adapter,
the DVI analog audio inputs on your TV allow
you to receive left and right audio from your
DVI device. (Not compatible with PC)
i) SERVICE
Service connection for qualified service engineer.
➢For further details about connection, refer to
pages 55~59.
➢Whenever you connect an audio or video system
to your television, ensure that all elements are
switched off. Refer to the documentation
supplied with your equipment for detailed
connection instructions and associated safety
precautions.
c
(
BP68-00613A-00Eng 5/17/06 1:25 PM Page 10

English - 11
Infrared Remote Control
r.
em
e
Selects a target device to be
controlled by the Samsung remote
control (TV, DVD, STB, CABLE, VCR)
Turns the TV on and off
Direct channel selection
One or two-digit channel selection
TV mode Selection
Current time display
VCR/DVD Function
(Rewind, Stop, Play/Pause, Fast/Forward)
Volume increase
Volume decrease
Temporary sound switch-off
Menu display/
Teletext index
Move to the required menu option/
Adjust an option value
respectively
Picture-In-Picture On/Off/
Teletext page hold
Sound effect selection
(Refer to page 41)
Picture effect selection
(Refer to page 27)
Sound mode selection
TruSurround XT mode selection
(Refer to page 43)
Used during set up of this Samsung
remote control, so that it will work
compatibly with other devices (VCR,
Cable Box and DVD).
External input selection
Switch repeatedly between the last two
channels displayed/
Teletext Sub-page
DNIe ON/OFF
Automatic switch-off
(Refer to page 47)
Next channel/
Teletext next page
Previous channel/
Teletext previous page
Exit menu/
Teletext cancel
Information display/Teletext reveal
(Refer to page 26)
Teletext display/
Mix both teletext information and
the normal broadcast
Picture still (Refer to page 32)
Fastext topic selection
Picture size (Refer to page 31)
If your remote control is not functioning
properly, take out the batteries and press
the reset button for about 2~3 seconds.
Re-insert the batteries and try using the
remote control again.
➢The performance of the remote control may be affected by bright light.
➢This is a special remote control for the visually impaired, and has Braille points.
PIP functions:
-Swapping the main and the sub
picture (SWAP)
-Channel selection (P )
(Refer to page 39)
BP68-00613A-00Eng 5/17/06 1:25 PM Page 11

English - 12
T
th
In
yo
de
re
◆
◆
➢
Inserting the Batteries in the Remote Control
You must insert or replace the batteries in the remote control when
you:
◆Purchase the television
◆Find that the remote control is no longer operating
correctly
1Lift the cover at the back of the remote control upward as shown in
the figure.
2Install two AAA size batteries.
➢ Make sure to match the “+” and “–” ends of the batteries with
the diagram inside the compartment.
3Close the cover as shown in the figure.
➢ Remove the batteries and store them in a cool, dry place if
you won’t be using the remote control for a long time.
The remote control can be used up to about 23 feet from the
TV. (Assuming typical TV usage, the batteries last for about
one year.)
BP68-00613A-00Eng 5/17/06 1:25 PM Page 12

To view television channels correctly, a signal must be received by
the set from one of the following sources:
◆An outdoor aerial
◆A cable television network
◆A satellite network
◆An indoor aerial
1In the first three cases, connect the aerial or network input cable to
the ANT IN jack on the rear of the television.
2If you are using an indoor aerial, you may need to adjust its
position when tuning your television until you obtain a picture that
is both sharp and clear.
For further details, refer to:
◆“Storing Channels Automatically” on page 18.
◆“Storing Channels Manually” on page 19.
➢When installing or re-installing your TV, be sure to use the
supplied coaxial antenna cable. If you connect using a different
coaxial cable, there is risk of noise or interference to the screen
image. (You must not use another general purpose cable.
Use the 3M/5M/7M cable supplied by Samsung.)
In order to watch television programmes broadcast via a satellite network,
you must connect a satellite receiver to the rear of TV. Also, in order to
descramble a coded transmission signal, you must connect a decoder to the
rear of TV.
◆Using a RCA cable
Connect the receiver (or decoder) RCA cable to one of the RCA
connectors on the rear of the television.
◆Using a coaxial cable
Connect a coaxial cable to the:
- Receiver (or Decoder) output socket.
- Television aerial input socket.
➢If you wish to connect both a satellite receiver (or decoder) and
a VCR, you should connect the:
◆Receiver (or Decoder) to the VCR
◆VCR to the television
Otherwise, connect the receiver (or decoder) directly to the
television.
English - 13
Connecting to an Aerial or Cable Television Network
Connecting a Satellite Receiver or Decoder
Rear of the TV
Cable Television
Network
or
Rear of the TV
Satellite Receiver/Decoder
RCA
cable
Coaxial
cable
n
n
BP68-00613A-00Eng 5/17/06 1:25 PM Page 13

English - 14
Placing Your Television in Standby Mode
Switching Your Television On and Off
Your television can be placed in Standby mode, in order to reduce
the power consumption.
The Standby mode can be useful when you wish to interrupt
viewing temporarily (during a meal, for example).
1Press the POWER ()button on the remote control to turn the
screen off.
Result:The STAND BY/TEMP indicator on the front of the
television turns on.
2To turn the screen back on, simply press the POWER ()button
again.
➢You can also switch on by pressing the P/,TV or any
numeric button on the remote control.
☛Do not leave your television in Standby mode for long
periods of time (when you are away on holiday, for
example). Turn your television off by pressing the power
switch on the back of the set. It is best to unplug the set
from the mains and aerial.
Plug the mains lead to the rear of your television.
1Plug the mains lead into an appropriate socket.
➢The main voltage is indicated on the rear of the television
and the frequency is 50 or 60Hz.
2Press the power switch on the side of the television toward
“ON” (I).
3Press the POWER ()button on the remote control (or the
“PICTURE ON/OFF” button on the front of the television).
Result:The programme that you were watching last is re-
selected automatically. However, if a SCART signal
input is present, the SCART signal has priority.
➢If you have not yet stored any channels, No clear picture
appears. Refer to “Storing Channels Automatically” on
page 18 or “Storing Channels Manually” on page 19.
4To switch your television off, press the power switch toward
“OFF” (O).
Depending on the model
Depending on the model
SP56K3HX / SP61K3HX
SP42L6HX / SP46L6HX / SP50L6HX / SP61L6HX / SP67L6HX
T
T
th
BP68-00613A-00Eng 5/17/06 1:25 PM Page 14

English - 15
Becoming Familiar with the Remote Control
Button Viewing Function Menu Function
Used to display the next
stored channel.
Used to display the
previous stored channel.
Used to display the
on-screen menu system.
Used to return to the previous
menu or normal viewing.
-
-
-
-
Used to:
◆Display a sub-menu
containing selections for
the current menu option.
◆Increase/decrease a
menu option value.
Used to confirm your choice.
Used to display the corresponding channels.
➢ For double digit channels, the second digit must be
pushed immediately after the first. Failure to do this
will result in a single digit channel being displayed.
Used to increase the volume.
Used to decrease the volume.
Used to switch the sound off temporarily.
➢ To turn the sound back on, press this button
again, or press the or button.
Press the PRE-CH button. The TV will switch to the last
channel viewed. To quickly switch between two channels
that are far apart, select the first channel, then use the
numeric buttons to select the second channel. Then, use the
PRE-CH button to quickly alternate between them.
to
Used to exit from the menu
system and return to normal
viewing directly.
Used to select a channel numbered ten or over.
Press this button, and the “
-- ” symbol is displayed.
Enter the two-digit channel number.
- / --
The remote control is used mainly to:
◆Change channels and adjust the volume.
◆Set up the television using the on-screen menu system.
The following table presents the most frequently used buttons and
their functions.
MUTE
()
P
MENU
()
EXIT
()
PRE-CH
BP68-00613A-00Eng 5/17/06 1:25 PM Page 15

W
s
i
If
English - 16
Plug & Play Feature
Plug & Play
Start Plug & Play.
OK
Check antenna input.
OK
Plug & Play
Enjoy your watching.
Plug & Play
Enter Exit
Enter Skip
Auto Store
P 1 C
--
40 MHz
0 %
Start
Enter Skip
OK
Plug & Play
Language
English
Move Enter Skip
Plug & Play
Area
Asia/W.Europe
CIS/E.Europe
China
Hong Kong/UK
Move Enter Skip
Plug & Play
Clock Set
--
:
--
am
Enter Skip
Plug & Play
Clock Set 12 : 00 am
Move Adjust Enter Skip
When the television is initially powered on, several basic customer
settings proceed automatically and subsequently.
The following settings are available.
1If the television is in standby mode, press the POWER ()button
on the remote control.
Result:The message to start Plug & Play is displayed.
2To start Plug & Play, press the ENTER ()button.
Result:The Language menu is displayed.
➢The Language menu will automatically appear after several
seconds, even if the ENTER ()button is not pressed.
3Select the appropriate language by pressing the …or †button.
Press the ENTER ()button.
Result:The message to check the connected status of the
antenna is displayed.
4Make sure that the antenna is connected to the TV.
Press the ENTER ()button.
Result:The Area menu is displayed.
5Select your country or area by pressing the …or †button.
Press the ENTER ()button.
Result:The menu to select channels is displayed.
6To start channel store, press the ENTER ()button.
Result:The search will end automatically. Channels are sorted
and stored in the order which reflects their position in
the frequency range (with lowest first and highest last).
When this has finished, the menu to set the time will be
displayed.
➢To stop the search before it has finished or return to normal
viewing, press the MENU ()or the ENTER ()button.
➢Press the ENTER ()button to set the clock.
7Press the œor √button to select the hour, minute, or am/pm.
Set these by pressing the …or †button.
➢You can enter the hours or minutes by using the numeric
buttons on the remote control.
8The settings are complete, and the stored channel will be
activated.
continued...
BP68-00613A-00Eng 5/17/06 1:25 PM Page 16

When you start using your television for the first time, you must
select the language which will be used for displaying menus and
indications.
1Press the MENU ()button.
Result:The main menu is displayed.
2Press the …or †button to select Setup.
Result:The Setup menu is displayed.
3Press the ENTER ()button.
4Press the …or †button to select Language.
Press the ENTER ()button.
Result:The available languages are listed.
5Select the appropriate language by pressing the …or †button.
Press the ENTER ()button.
6Press the EXIT button to exit.
If you want to reset this feature...
1Press the MENU ()button.
Result:The main menu is displayed.
2Press the …or †button to select Setup.
Result:The Setup menu is displayed.
3Press the ENTER ()button.
4Press the ENTER ()button again to select Plug & Play.
Result:The message to start Plug & Play is displayed.
➢For further details on settings, refer to the previous page.
Choosing Your Language
English - 17
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : On
Panel Lock : Off
PC
Setup
TV
Move Enter Return
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : On
Panel Lock : Off
PC
Setup
TV
Move Enter Return
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : On
Panel Lock : Off
PC
Setup
TV
Move Enter Return
English
Start Plug & Play.
OK
Plug & Play
Enter Return
r
d
.
e
l
n.
BP68-00613A-00Eng 5/17/06 1:25 PM Page 17

Y
ne
W
English - 18
Storing Channels Automatically
Area : Asia/W.Europe
Auto Store
Manual Store
Add/Delete
Sort
Name
Fine Tune
LNA : Off
Channel
TV
Area : Asia/W.Europe
Auto Store
Manual Store
Add/Delete
Sort
Name
Fine Tune
LNA : Off
Channel
TV
Move Enter Return
Move Enter Return
Auto Store
P 1 C
--
40 MHz
0 %
Start
Area : Asia/W.Europe
Auto Store
Manual Store
Add/Delete
Sort
Name
Fine Tune
LNA : Off
Channel
TV
Move Enter Return
Asia/W.Europe
CIS/E.Europe
China
Hong kong/UK
Australia
Enter Return
You can scan for the frequency ranges available to you (availability
depends on your country). Automatically allocated programme numbers
may not correspond to actual or desired programme numbers. However
you can sort numbers manually and clear any channels you do not wish
to watch.
1Press the MENU ()button.
Result:The main menu is displayed.
2Press the …or †button to select Channel.
Result:The Channel menu is displayed.
3Press the ENTER ()button.
Result:The Area is selected.
4Press the ENTER ()button again.
Result:The available areas are listed.
5Select your Area by pressing the …or †button.
6Press the ENTER ()button.
7Press the …or †button to select Auto Store.
Press the ENTER ()button.
Result:The Auto Store menu is displayed.
8Press the ENTER ()button again to start the search.
Result:The search will end automatically. Channels are sorted
and stored in the order which reflects their position in
the frequency range (with lowest first and highest last).
The programme originally selected is then displayed.
➢To stop the search before it has finished, press the MENU
()or the ENTER ()button.
9When the channels have been stored, you can:
◆Sort them in the order required (“Sorting the Stored
Channels” on page 22).
◆Clear a channel (“Skipping Unwanted Channels” on page 21).
◆Fine-tune channel reception if necessary (“Fine Tuning
Channel Reception” on page 26).
◆Assign a name to the stored channels (“Assigning Names to
Channels” on page 23).
◆Activate/deactivate the Digital NR (Noise Reduction) feature
(“Using the Digital NR (Noise Reduction) Feature” on page 40).
◆Activate/deactivate the LNA (Low Noise Amplifier) feature
(“Using the LNA (Low Noise Amplifier) Feature” on page 25).
BP68-00613A-00Eng 5/17/06 1:25 PM Page 18

You can store television channels, including those received via cable
networks.
When storing channels manually, you can choose:
◆Whether or not to store each of the channels found.
◆The programme number of each stored channel which you
wish to identify.
1Press the MENU ()button.
Result:The main menu is displayed.
2Press the …or †button to select Channel.
Result:The Channel menu is displayed.
3Press the ENTER ()button.
4Press the …or †button to select Manual Store.
Press the ENTER ()button.
5If necessary, select the broadcasting standard required.
Press the …or †button to select Colour System.
Press the ENTER ()button.
6Select the required colour standard by pressing the …or †
button. Press the ENTER ()button.
Result:The following options are available.
(depending on the model)
AUTO - PAL - SECAM - NTSC4.43 - NTSC3.58
7Press the …or †button to select Sound System.
Press the ENTER ()button.
8Select the required sound standard by pressing the …or †
button. Press the ENTER ()button.
Result:The following options are available.
BG - DK - I- M
Storing Channels Manually
English - 19
Area : Asia/W.Europe
Auto Store
Manual Store
Add/Delete
Sort
Name
Fine Tune
LNA : Off
Channel
TV
Move Enter Return
Programme : P 1
Colour System : AUTO
Sound System : BG
Channel : C 5
Search : 175 MHz
Store : ?
Manual Store
TV
Move Enter Return
Programme : P 1
Colour System : AUTO
Sound System : BG
Channel : C 2
Search : 48 MHz
Store : ?
Manual Store
TV
Move Enter Return
AUTO
PAL
SECAM
NTSC4.43
NTSC3.58
Programme : P 1
Colour System : AUTO
Sound System : BG
Channel : C 2
Search : 48 MHz
Store : ?
Manual Store
TV
Move Enter Return
BG
DK
I
M
continued...
d
.
).
).
.
BP68-00613A-00Eng 5/17/06 1:25 PM Page 19

Y
op
ha
A
d
\
English - 20
Programme : P 1
Colour System : AUTO
Sound System : BG
Channel :C05
Search : 175 MHz
Store : ?
Manual Store
TV
Adjust Enter Return
Programme : P 1
Colour System : AUTO
Sound System : BG
Channel : C 5
Search : 175 MHz
Store : ?
Manual Store
TV
Adjust Enter Return
Programme : P 1
Colour System : AUTO
Sound System : BG
Channel : C 5
Search : 175 MHz
Store : OK
Manual Store
TV
Move Enter Return
9If you know the number of the channel to be stored, see the
following steps.
◆ Press the …or †button to select Channel.
Press the ENTER ()button.
◆ Press the …or †button to select C(Air channel) or
S(Cable channel).
◆ Press the √button.
◆ Press the …or †button to select the required number.
Press the ENTER ()button.
➢You can select the channel directly by pressing
the numeric buttons on the remote control.
➢If there is abnormal sound or no sound, re-select the
sound standard required.
10 If you do not know the channel numbers, select Search by
pressing the …or †button. Press the ENTER ()button.
Press the …or †button to start the search.
Press the ENTER ()button.
Result:The tuner scans the frequency range until the first
channel or the channel that you selected is received on
your screen.
11 To assign a programme number to a channel, select Programme
by pressing the …or †button. Press the ENTER ()button.
12 Press the …or †button until you find the correct number.
Press the ENTER ()button.
➢You can select the programme directly by pressing
the numeric buttons on the remote control.
13 To store the channel and associated programme number, select
Store by pressing the …or †button. Set to OK by pressing the
ENTER ()button.
14 Repeat steps 9to 13 for each channel to be stored.
15 Press the EXIT button to exit.
☛Channel mode
◆P (Programme mode): When completing tuning, the
broadcasting stations in your area have been assigned to
position numbers from P00 to P99. You can select a
channel by entering the position number in this mode.
◆C(Air channel mode): You can select a channel by entering
the assigned number to each air broadcasting station in this
mode.
◆S(Cable channel mode): You can select a channel by entering
the assigned number for each cable channel in this mode.
BP68-00613A-00Eng 5/17/06 1:25 PM Page 20