SanaLoma Laser UFO Dice Tower User manual

dtwenty
UFO Dice Tower Assembly Instructions - Page 1
Section 1 - Bottom Tray Section 4 - UFO saucer - center section
Cutting and Engrving at LightSpeed
www.SanaLomaLaser.com
SanaLoma
Laser LLC
This kit is made from 3mm (1/8") Baltic Birch Plywood
and has been designed for persons over the age of 12.
THIS PRODUCT IS NOT A TOY!
To assemble the UFO Dice Tower, follow each section using the parts indicated. You will need glue for some parts and some pieces may fit tightly, so keep
the glue and sandpaper handy and have fun! This kit was designed by Sanaloma Laser, LLC The areas indicate where to glue.yellow
beam up
alien cows
dungeon
dice tray
dragons
ufo tower
spaceship
Start by collecting the Base piece
and the eight Side pieces. Glue the
slots on the Base piece and the
BACK side ends of each Side
piece. Place the Side pieces onto
the edge of the Base piece with the
alien text facing out. Set aside to
dry.
Section 2 - UFO Legs
Section 3 - Cow
l
e
g
l
e
g
l
e
g
l
e
g
l
e
g
l
e
g
Long tab
Short tab
Alien Text
on outside.
Glue the three Legs together
by matching the leg pieces.
The text should show on both
sides when glued back to
back. Be sure to match the
tab sizes and align them
evenly. Set aside to dry.
c
c
Glue the Cow together next. The piece with the tail is the center. The
two outside pieces have alien text that goes to the outside. Be sure
the legs are flat on the bottom to allow it to stand. Set aside to dry.
x16
Short side to
outside edge
of ring.
Add the Side Panel supports to the
Center Disks. Glue them in place with
the short side to the outside edge of
the Center Disk. Each disk has 16
supports. See picture.
Add the 8 Side Panels by gluing them to the top of the supports.
The short side of the these panels go to the inside of the Center
Disk. See picture. COMPLETE TOP AND BOTTOM DISKS.
x8

Section 5 - Dice Tower
UFO Dice Tower Assembly Instructions - Page 2
Section 6 - UFO Assembly
www.SanaLomaLaser.com
Cutting and Engraving at LightSpeed
SanaLoma
Laser LLC
This kit is made from 3mm (1/8") Baltic Birch Plywood
and has been designed for persons over the age of 12.
THIS PRODUCT IS NOT A TOY!
xz
look out
Start the Dice Tower by
finding the side panel with the
widest tabs at top. Lay it on a
flat surface with the alien text
down. Glue the 3 tumble slats
tabs to the panel.
Next glue the
second side panel
with slots to the top
of the tabs from the
tumble slats.
x3
Holding the two sides together pickup the piece and
glue the two additional sides to the dice tower. The
extra wide tabs should be at the top and all the alien
text should be facing out. Make sure the sides are
seated fully to allow the dice tower to fit into the
UFO saucer assembled in the next section.
below
Use the two Alignment pieces the help assemble the UFO. Glue the disks in the
slots and on the overlapping flat pieces. The design on the Alignment pieces
should be facing OUT and the bottom half pieces (above) should have the best
side facing down. Be sure the leg holes are aligned correctly.
Be sure leg holes
are aligned correctly.
First piece goes all
the way to the slot
stopper.
It is best to finish this entire section before the glue dries completely to allow for
minor adjustments during the final assembly.
The top half pieces slide on the Alignment pieces with their best side facing UP.
Be careful with the last two disks, make sure the tabs are matched correctly.
Make sure the tab slots on the last
two pieces are matching before glueing
them in place.
Add the dice
tower to the UFO
by inserting it
bottom first into
the top of the
UFO. Be sure
the tabs match
the slots on the
UFO. You do not
have to glue it.
Add the cap piece
to the top of the
UFO.
Assembly is now complete. If
you would like you can glue
the legs to the UFO or leave
them unglued for easier
storage.

UFO Dice Tower Assembled
www.SanaLomaLaser.com
Cutting and Engraving at LightSpeed
SanaLoma
Laser LLC
This kit is made from 3mm (1/8") Baltic Birch Plywood
and has been designed for persons over the age of 12.
THIS PRODUCT IS NOT A TOY!