SANKI S-CON MINI Series Service manual

1
S-CONⓇMINI-PLAMO
SPM
OPERATING AND SERVICE MANUAL

2
Thank you very much for purchasing our S-CON®MINI series. This manual is
specialized for the belt handling of S-CON®MINI-PLAMO. Before machine use,
please carefully read this as well as S-CON®MINI series operating and service
manual. Keep the manual where the machine is installed,
so that it may be referred to when needed.
TABLE OF CONTENTS
1．Belt removal in maintenance ― Rod removal ……………
2．Sprocket alignment on driving shaft ………………………
3．Caution when joining belt ………………………………………
4．Pivot rod insertion …………………………………………………
5．Belt slackness (Catenary sag) …………………………………
3
4
4
5
6

3
1
BELT REMOVAL IN MAINTENANCE ― ROD REMOVAL
1. Remove rod with hammer and
punch as follows.
2. Rod removal can be easier by
supporting opposite belt edge
with fixing tool, such as shown
in picture below.
3. To remove rod, use punch on opposite
side of rod head.
Hammer opposite side of
rod head through punch.
4. If you do not have a fixing tool (such
as shown in picture of step 2), hold
opposite belt edge as shown in picture
below.
5. Pull out rod with side cutter (optional).
Hold rear of rod
head with side
cutter and pull
out rod.

4
When attaching sprockets on driving shaft, it is very important to align teeth of all the sprockets correctly.
For this purpose, sprockets usually have alignment marks as shown in picture below.
2
SPROCKET ALIGNMENT ON DRIVING SHAFT
3
CAUTION WHEN JOINING BELT
Align sprocket teeth.
Alignment mark
Correct joining position
(not having same patterns)
Line B
Line A
Rod side
Non rod
side
Non rod
side
Non rod
side
Example of incorrect joining position
(having same patterns)
Example of incorrect joining position
(having same patterns)
×
×
B
A
B
A
*BELT SLACKNESS ADJUSTMENT AFTER TEST RUN
If it is necessary to adjust belt length after test run, be sure to make
adjustment by increasing or decreasing set of A and B lines (2 links) as
shown in picture, left.
This method is very important to maintain “brick pattern structure” and to
keep belt strength.
Line B
Line B
Line A
Line A

5
ネットの
進行方向
4
PIVOT ROD INSERTION
●Function of snap rod system
1. Insert rod.
2. Hammer rod until in fixing position.
3. Cut off extra rod length, slightly
inside belt edge.
Once belt length is determined, carry out belt endless processing by inserting pivot rod.
Rod head
Module link
Snap rod
●Rod end chamfering

6
5
BELT SLACKNESS (CATENARY SAG)
Modular belt length remarkably changes depending on load and ambient temperature. Extra belt length
to adapt to condition changes is managed on return side by sagging where belt is not supported.
For specifications of belt slackness, refer to figures.
If necessary, adjust belt length to make belt tension (or slackness) appropriate. In this case, make
adjustment by increasing/decreasing belt lines or by adjusting take-up system if equipped.
U
M
U
900-1200mm
35”-48”
R1
25-100mm
1”-4”
SR
U
M
ST
2-4m 6-12ft
TU
M
2m
25-100mm
4m 12ft
R1
250-500mm
10”-20”
25-100mm
1”-4”
900-1200mm
35”-48”
900-1200mm
35”-48”

7
MEMO

8
LOGISTIC TECHNOLOGY DEPT., MACHINERY SYSTEMS ADMINISTRATION DIV.
Customer Center
TEL [phone] FAX [phone]
URL https://www.hansou.jp
E-mail [email protected]
Manual Code SPM-004 ‘23/01
●Particular attention is given to the manufacture and transportation of SANKI
conveyors. However, if you need any information about the use or failure of the
machine or any other matters, please contact our customer service. Also do not
hesitate to ask us for information about conveyors in general.
●The specification given in this manual are subject to change without notice.
hansou.jp
Contact us