Sanlien pALERT S303 User manual
pALERT S303
Quick Start Guide
http://www.sanlien.com
1
Sensor Quick Start Guide
Table of Contents
1
Hardware Requirement ...............................................................................3
1.1
Sensor and Accessories........................................................................................................3
1.2
Delay Time Functions from Button ...................................................................................5
The IP Showing ...............................................................................................................6
The Power Off .................................................................................................................6
1.3
LCD Showing Description ..................................................................................................7
Main Status Description .................................................................................................7
Booting Sequence ............................................................................................................7
2
Installation.....................................................................................................8
2.1
Installation Sequence...........................................................................................................8
2.2
Mount Direction Description............................................................................................10
Components Definition.................................................................................................10
Mount Mode ..................................................................................................................10
3
Software Description ..................................................................................11
3.1
Computer IP setting..........................................................................................................11
3.2
Web Service........................................................................................................................13
Web Login......................................................................................................................13
Parameter settings.........................................................................................................14
Waveform & Recording................................................................................................14
Waveform Report..........................................................................................................15
Password........................................................................................................................16
NTP (Network Time Protocal) Setting........................................................................16
Self-IP Setting................................................................................................................17
DNS Setting....................................................................................................................17
Record Download & SOH ............................................................................................18
3.3
WinSCP Operation (Engineer Use) .................................................................................20
WinSCP Login...............................................................................................................20
WinSCP Interface .........................................................................................................20
2
Sensor Quick Start Guide
WinSCP Retrieves Parameter File ..............................................................................21
Earthquake Event Checking........................................................................................23
3.4
PuTTY Operation (Engineer Use) ...................................................................................24
PuTTY Login.................................................................................................................24
PuTTY Login Window .................................................................................................24
Modify Sensor IP...........................................................................................................25
Modify NTP ...................................................................................................................27
3
Sensor Quick Start Guide
1Hardware Requirement
1.1 Sensor and Accessories
Sensor Power Cable &
GPS Antenna
Sets
Ethernet Cable
& Connector Server &Hub
4
Sensor Quick Start Guide
Sensor Outlook
1. LCD Monitor：Live status presentation.
2. Button Function：Delay time in seconds for function.
3. Ethernet Port：Connecting Ethernet.
4. Power Port：DC Power connector.
5. A X Port：Auxiliary port for digital output and GPS antenna.
6. Sensor Port：Additional port for external velocity sensor.
7. GPS Antenna Port：Connector for GPS antenna.
2
3
4
5
6
1
7
5
Sensor Quick Start Guide
1.2 Delay Time Functions from Button
1 Second IP Showing
2 Seconds NTP restart
3 Seconds Exercise cancel function
4 Seconds Hardware part reloading parameters
5 Seconds Firmware version showing
6 Seconds Reloading parameters without IP check (for saving time)
7 Seconds Firmware upgrading via internet
8 Seconds 1. Global recoding mode
2. Confirm this mode by following 2 seconds pressing
3. Stop this mode by following 3 seconds pressing
9 Seconds Test mode
Following 4 seconds：EEW Exercise in 30 seconds
Following 3 seconds：Warning cancel
Following 9 seconds：Back to normal mode
Following 10seconds：Relay self-test
12 Seconds Power off
Factory Reset：Time delay in seconds from sensor button following the
sequence 15162612
Default IP
Address：192.168.255.1
Netmask：255.255.255.0
Gateway：192.168.255.254
Note：See the figures below
6
Sensor Quick Start Guide
The IP Showing
Press 1 second from button, LCD shows sensor IP.
The Power Off
Press 12 seconds from button, LCD shows sensor “Power off” - >”System is
off”. After that removing power connector, LCD will disappear message.
7
Sensor Quick Start Guide
1.3 LCD Showing Description
Main Status Description
Booting Sequence
After the powering is on, the LCD will show “Booting” and “Offsetting”, if it
keeps showing “Offsetting”, please put sensor to the more stable platform(ground)
to avoid the background noise.
Current Date Current Time
Sensor Type Firmware version
8
Sensor Quick Start Guide
2Installation
2.1 Installation Sequence
Step 1：Drilling a hole with sleeve anchor diameter and depth on the wall or
platform(ground), diameter and depth around 0.5 and 1.58 inches.
Step 2：Taps the sleeve in hole with hammer.
Step 3：Drive the anchor into sleeve part and keep a sufficient distance (around
0.31 inch).
Step 4：Hook sensor on anchor.
Anchor Hole
Sleeve
Anchor
Anchor hole Sleeve
Anchor
9
Sensor Quick Start Guide
Step 5：Tight these 3 hex screws on the wall or platform(ground). Level the
bubble on the center (horizontal requirement).
Step 6：GPS Antenna should be encapsulated with glue as below.
#. Put the GPS connector cover.
#. Inject the glue.
#. Cover the cap after injected.
Hex screws
Bubble on the center
10
Sensor Quick Start Guide
2.2 Mount Direction Description
Components Definition
Mount Mode
“WA ” and “EASTWARD” mount: Output positive value is in upward,
northward and westward direction (negative is on the contrary).
“NORTHWARD” mount: Output positive is in upward, northward and
eastward direction (negative is on the contrary). The 3 modes can be set in
software.
NOTICE: The definition of wave polarization is reverse between WA &
NORTHWORD mounting mode from EAST/WEST directions, please
contact manufactory when having the wall mounting requirement.
E(-)
N(+)
U(+)
EASTWARD
E(+)
N(+)
U(+) NORTHWARD
(Default Mode)
E(-)
N(+)
U(+)
WALL
Mount
East / West(c/Y)
North / South (b/X)
p / Down (a/Z)
11
Sensor Quick Start Guide
3Software Description
3.1 Computer IP setting
To connected with sensor, computer(laptop) should be the same IP domain with
it, here under is the description.
Step 1:
Right click WIFI (Fan symbol) and select “Network and Internet”.
Step 2:
Select change adaptor settings
1
2
Network and Internet
Change adaptor settings
12
Sensor Quick Start Guide
Step 3:
Right click and select properties.
Step 4:
Click IP-V4 and set the same IP with sensor IP domain, for example,
default sensor IP is 192.168.255.1, you can only change the 4
th
number
with 192.168.255.xxx (the number below 254) in it.
properties
Ethernet
Internet Protocal Version 4
13
Sensor Quick Start Guide
3.2 Web Service
Web Login
After changing computert IP, open web browzer(DO NOT use IE) with
sensor IP at address bar(If there’s no connection with any ethernt cable, the
defaut IP will be “192.168.255.1”). Before clicking “SEND”, insert “admin”
as username, “p@ssw0rd” as password, clicking “SEND” to enter the main
page.
Main properties list on the left side window of main page.
admin
1111
14
Sensor Quick Start Guide
Parameter settings
Click “Parameter Settings”, and it appears configuration parameters on the
right-side window, click “SAVE” and” Reload” after setting changed.
Wa eform & Recording
Web service provides real time waveform, when click “Waveform &
Recording” on the main property, a new streaming wabpage will pop up, clicking
“Start streaming” can see real time waveform, It also provides a simulation, an
square plus with 100 gal generates during 0.8 second after clicking “Calibration”.
The “Offset” button serves the manully offsetting in anytime.
15
Sensor Quick Start Guide
Wa eform Report
Click ”Waveform Report” to check the recorded event file, then click the
file name to see the event waveform report as below.
16
Sensor Quick Start Guide
Password
Password can be changed by “admin” user, clicking “Password” . Click
“CHANGE” after double comfirmed the password.
NTP (Network Time Protocal) Setting
Sensor provides the NTP time synchronization service, please enable port 123
to open this function. NTP can be inserted domain name or IP addresss. Click
“NTP Setting” at left main poroperty page and then clicking “NETWORK
RESTART” after modifing “UPDATE” and “ADD ON”.
17
Sensor Quick Start Guide
Self-IP Setting
If there is no any internet(intranet) connected with sensor its default IP
will be as “192.168.255.1” even in DHCP (Dynamic Host Configuration
Protocal) mode. DHCP mode means that if sensor connected with hub or
switch, it automatically gets an IP address. sensor can be in the static IP
mode as well. The setting sequence description as below.
0. Click “Networking Setting”
1. Click to “DHCP OFF”
2. Insert IP-V4
3. Insert subnet mask
4. Insert gateway
5. Click “UPDATE” and “NETWORK RESTART”
6. Power cycle sensor physically
DNS Setting
18
Sensor Quick Start Guide
If sensor connects via internet, the DNS (Domain Name System) needs to be enabled The
DNS can be enabled as google public IP by 8 8 8 8(or 8 8 4 4) Besides that, it can be defined
as privacy DNS in individual area as well Click “DNS Setting” then Click “UPDATE” after
setting up at right side window
Record Download & SOH
Click “Record” then all the files can be downloaded from “Download” word
19
Sensor Quick Start Guide
Click “SOH Information”, status of health shows the basic health condition, the items see
below. If GNSS connected stable, the GNSS shows “sync.”, LCD always appea s a hea t -beat
cycling dot on the ight top of location between the numbe of fi mwa e ve sion.
Notice: If senso epeat showing “no heartbeat” on LCD, sho t pin1 & pin9 with a dupont
line f om senso po t afte powe off it, and then powe on again, the status becomes
no mal.
Table of contents
