ROSE DISPLAYS CABLE CLIP User manual

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
Step 1
Insert single ball of ball chain into inner
channel of Cable Clip. The cable should
snap into place. Fig. 1
Align one round end of cable clip with top
channel of the rail and insert. Once in
place, insert end of ball chain into channel.
Then press down on the other round end of
the cable clip and slide into rail by pushing
on the clip. Fig. 2
Note: Be sure to push on the cable clip in
order to slide the ball chain into place. Do
not pull on, or push against, the ball chain
as this will cause it to bind in the channel.
Note: Position CableClip about halfway
down each SuperSnap. Fig. 3
Step 2
Insert AnoConnector into rail of one
SuperSnap. Make sure tabs face upward. The
side with one tab must go in first. Fig. 4
Step 3
Insert threaded rod halfway into clip rail of
the same SuperSnap. Fig. 5
Step 4
Push the second piece of SuperSnap onto
both AnoConnector and the threaded rod.
Push together until
both holders meet. Fig. 6 Repeat steps 2-4
for additional SuperSnaps.
Instructions for assembly
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapAnoConnectorCCBC
Figure 6
Figure 3
SuperSnap™ with AnoConnector Instruction Sheet
Figure 1 Figure 2
Figure 4
Figure 5
Page 1 of 2
AnoConnector
06-2930
SuperSnap
12S300
6” Rod
97-0304-06
CableClip
06-5050
End Caps
06-5475
Ball Chains
96-0302P

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
(continued)
Step 5
Snap all sections of the SuperSnap
open. Fig. 7
Note: It is easier to open and close
the SuperSnap by starting at one
end and working your way down
the holder.
Step 6
Insert graphic into one section of
SuperSnap (top and bottom). Fig. 8
Step 7
To close, snap the SuperSnap shut.
Fig. 9
Step 8
You should now have one graphic in
place. Repeat steps 5-7 for hanging
additional graphics.
Step 9
Push end caps into place. Fig 10
Step 10
Suspend holders. Finished Look
Important note:
Please save and reuse the
SuperSnap, End Caps and
CableClips for future projects.
Instructions for assembly
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapAnoConnectorCCBC
SuperSnap™ with AnoConnector Instruction Sheet
Page 2 of 2
Finished Look
Open all holders Figure 8Figure 7
Figure 10Figure 9Insert posters
AnoConnector
06-2930
SuperSnap
12S300
6” Rod
97-0304-06
CableClip
06-5050
End Caps
06-5475
Ball Chains
96-0302P

Parts
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapAnoConnectorCCBC
Figure 6
Figure 3
SuperSnap™ with AnoConnector Instruction Sheet
Figure 4
Figure 5
Page 1 of 2
AnoConnector
06-2930
SuperSnap
12S300
6” Rod
97-0304-06
CableClip
06-5050
End Caps
06-5475
Ball Chains
96-0302P
Step 1
Insert single ball of ball chain into inner
channel of Cable Clip. The cable should
snap into place. Fig. 1
Align one round end of cable clip with top
channel of the rail and insert. Once in
place, insert end of ball chain into channel.
Then press down on the other round end of
the cable clip and slide into rail by pushing
on the clip. Fig. 2
Note: Be sure to push on the cable clip in
order to slide the ball chain into place. Do
not pull on, or push against, the ball chain
as this will cause it to bind in the channel.
Note: Position CableClip about halfway
down each SuperSnap. Fig. 3
Step 2
Insert AnoConnector into rail of one
SuperSnap. Make sure tabs face upward. The
side with one tab must go in first. Fig. 4
Step 3
Insert threaded rod halfway into clip rail of
the same SuperSnap. Fig. 5
Step 4
Push the second piece of SuperSnap onto
both AnoConnector and the threaded rod.
Push together until
both holders meet. Fig. 6 Repeat steps 2-4
for additional SuperSnaps.
Instructions for assembly
Figure 1 Figure 2

Parts
(continued)
Step 5
Snap all sections of the SuperSnap
open. Fig. 7
Note: It is easier to open and close
the SuperSnap by starting at one
end and working your way down
the holder.
Step 6
Insert graphic into one section of
SuperSnap (top and bottom). Fig. 8
Step 7
To close, snap the SuperSnap shut.
Fig. 9
Step 8
You should now have one graphic in
place. Repeat steps 5-7 for hanging
additional graphics.
Step 9
Push end caps into place. Fig 10
Step 10
Suspend holders. Finished Look
Important note:
Please save and reuse the
SuperSnap, End Caps and
CableClips for future projects.
Instructions for assembly
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapAnoConnectorCCBC
AnoConnector
06-2930
SuperSnap
12S300
SuperSnap™ with AnoConnector Instruction Sheet
Page 2 of 2
Finished Look
Open all holders
6” Rod
97-0304-06
Figure 8Figure 7
Figure 10Figure 9Insert posters
CableClip
06-5050
End Caps
06-5475
Ball Chains
96-0302P