sanus accents FPA405 User manual

FPA405
INSTRUCTION MANUAL
If you have any questions along the way, just give us a call:
1-888-333-9952 (UK: 0800-056-2853) we’re ready to help!
We’ll Make It Stress-Free

2
Please check the following items:
Your TV and any accessories you plan to use do not exceed the
specified weight limit of your TV mount.
You read and understand these directions.
You refer to the documentation that came with your TV for
additional guidance.
You have the tools needed for installation.
If your TV bracket has built-in or integrated spacers (see
Figure 1), or mounting holes or slots that are wider than
11mm [.43 in.] (see Figure 2), you cannot use this product.
Call Customer Service for assistance.
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE
Before You Begin
<11mm
[.43 in.]
Figure 1
Figure 2

3
WARNING:
• This product is only designed to be used
with Sanus VuePoint television mounts
and mounted BELOW the television.
• This soundbar mount was designed to be
installed and utilized ONLY as specified
in this manual. The manufacturer is not
responsible for improper assembly, use,
or handling of this product.
• The wall must be capable of supporting five times the weight of the TV, mount,
and soundbar combined.
• Failure to follow these instructions could result in an unstable situation that may
result in property damage or personal injury.
Please contact Customer Service with any questions.

4
SANUS VUEPOINT TELEVISION MOUNT
Weight Limit for the FPA405 Items Needed
15 lb (6.8 kg)
DO NOT EXCEED!
CAUTION: Avoid potential personal injuries
and property damage!
You must verify that the weight of the TV plus the
soundbar mount, soundbar, and any accessories
is lower than the maximum weight rating of the
TV mount.
Phillips Screwdriver
Level

5
05 05
05
Arm Position
NOTE: TV/bracket
arms 05 should
be positioned as
vertically as possible.

6
NOTE: Not all hardware included will be used.
Supplied Parts and Hardware
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged,
do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts!
Parts and Hardware for STEP 1 (and 3)
01 x 2 x 2
02
x 2
03
x 4
04
Soundbar Bracket Arm “C” Washer
Keyhole Screw
Knob

7
05 x 2
x 2
06
TV Bracket Arm
Mount Spacer
Parts and Hardware for STEP 3 Hardware for TV Bracket
M4/M5
07 x 4
Large M4/M5
09 x 4
M6/M8
08 x 4
Large M6/M8
10 x 4
TV Screw Washers

8
Hardware for TV Bracket
M8 x 20mm
15 x 4
M6 x 25mm
14 x 4
M6 x 16mm
13 x 4
M5 x 16mm
12 x 4
M4 x 16mm
11 x 4
Screws for TVs with a Flat/Unobstructed Back

9
Hardware for TV Bracket
M8 x 40mm
20 x 4
M6 x 50mm
19 x 4
M6 x 40mm
18 x 4
M5 x 40mm
17 x 4
M4 x 40mm
16 x 4
Screws for TVs with Irregular/Obstructed Backs
21 x 4
Spacer for TVs
with Irregular/
Obstructed Backs

10
Check the compatibility of the soundbar bracket with your soundbar.
Assemble knobs 04 and screws 03 .
Attach the soundbar arms 01 to soundbar. Do not fully tighten the knobs 04 .
04
03
NOTE: When planning on the position of
the soundbar, make sure you will be able
to access the control buttons.
Mount Bracket Arms to Soundbar - Option 1
STEP 1

11
01
01
04
03

12
Mount Bracket Arms to Soundbar - Option 2
STEP 1
Check the compatibility of the soundbar bracket with your soundbar.
Assemble knobs 04 and screws 03 .
Some connections to the soundbar may require a “C” washer 02 to ensure that the
soundbar arms 01 lay flat on the soundbar. If required, slip a “C” washer 02 onto the
knob screws 03 and under the arms 01 and loosely tighten the knobs 04 .
04
03

13
01
01
04
04
02
02
02 03
04

14
Some soundbars will come with a manufacturer supplied hanger.
Attach the soundbar arms 01 to the soundbar hanger with knobs 04 and screws 03 .
Do not fully tighten the knobs 04 .
Mount Bracket Arms to Hanger - Option 3
STEP 1

15
01 01
04
03
SOUNDBAR
MANUFACTURER
SUPPLIED HANGER

16
STEP 2 Prepare TV
A
If yourTV is already mounted:
A. Remove any cables attached to theTV.
B. Remove theTV/bracket assembly from the wall
plate, arm assembly, or pillar. Please see your
TV wall mount installation manual for guidance.
HEAVY! You may need assistance with this step!
C. Remove theTV bracket from theTV.
IMPORTANT!
!Please see yourTV wall mount manual
for instructions on how to remove theTV
interface bracket.
!Save theTV hardware in case you want to use
theTV without the soundbar in the future.
!You must use the hardware provided with
this product instead of the hardware that
came with your mount.

17
B
C

18
STEP 3
Install TV Bracket with the TV/Bracket Arms
Determine the bolt diameter for your monitor
and your TV type - M4, M5, M6, or M8.
• ForTVs with a flat/unobstructed back, see
Step 3-1
• ForTVs with an irregular/obstructed back,
see Step 3-2
If you need extra space to accommodate
cables, recesses, or protrusions, see Step 3-2
that uses spacers.
Standard configurations are shown. For
special applications, contact Customer Service.
CAUTION: Use the shortest screw and
spacer combination needed to accommodate
cables, recesses, or protrusions. Using hardware
that is too long may damage your monitor’s internal
components!
Step 3-1 Step 3-2

19
STEP 3-1
NOTE: Soundbar must be mounted
below theTV as shown.
WARNING: You
must use the larger
washers 09 or 10
unless they do
not fit your tv
bracket.
11 12 13 14 15
07 08 09 10
06
06
05

20
STEP 3-2
16 17 18 19 20
21
06
06
05
07 08 09 10
NOTE: Soundbar must be mounted
below theTV as shown.
WARNING: You
must use the larger
washers 09 or 10
unless they do not fit
your tv bracket.