Sanyo CDF-R800 User manual

OPERATING
INSTRUCTIONS S* o
CDF-R800
Multi Control CD Receiver
(CD Changer Controller, FM/AM Tuner,
CD Deck Amplifier)
M3iE
DIGITAL AUDIO

Introduction
Thank you for purchasing the CDF-R800. This unit has many features, including:
18 cm /12 cm CD Compatible ■Auto Travel Preset (ATP)
■Scan Play, Repeat play, Shuffle Play ■Built in CD Changer controller
■PLL Synthesizer AM/FM/FM Stereo ■Full Logic Control Mechanism
Radio with Clock ■Electronic Audio Control
■12-FM plus 6-AM Preset ■High power Output (3oW x4)
In order to enjoy the features to their fullest and keep the unit in good working order
for along time, read this manual thoroughly and keep it for future reference.
Accessories
Mounting bracket Trim panel Removing levers
xl xl x2

Contents
Before use
Forsafe and efficient operation ................................... 3-4
Handling the CDs ................................................4
Location and function ofcontrol. .....................................5
Digital display ...................................................6
General operation
PowerOn/Off ...................................................7
Audio control ....................................................8
Selecting aprior display ...........................................9
Clock operation .................................................10
Cooperation
Howtoload, play, remove aCD.. ..................................11
CD modeselectbutton, Pause, selectinga track, Skipping ...............12
Scan, Repeat, Shuffle ............................................13
Radio operation
Howtoturn on the radioand select aband, Tuning .....................14
LO/DXbutton,Radiomodeselect button, Presetting stations . . . . . ...15-16
Changer operation .
Before operation ................................................16
How to play CDs, Pause, Selecting adisc/track .......................17
Skipping, Scan, Repeat, Shuffle.. ..................................18
Disc Scan, Disc Repeat, Disc Shuffle ................................19
Errorand Status indications.. ......................................20
Before Wiring and lnstaHation. ..................................20-21
Wiring .......................................................22-23
Installation .......................................................24
Unit removal .....................................................24
Troubleshooting ..............................................25-26

For safe and efficient operation
m
●This unit is designed to operate on +12 volt DC negative ground electrical systems
only.
g●Accordingtothismanual,installandoperate the unit. If you are not confident in
your ability to install the unit correctly, have it installed by aproffesional mobile
3electronics installation technician.
?
:●Do not try to open the unit nor to repair it yourself. If servicing is required, return
CD the unit to an authorized SANYO mobile audio dealer.
.When clean out the car, be sure not to get any water on the unit because it can be
damaged.
.Never put any other object in the Disc slot. The inside of the unit is precision equip-
ment that could be damaged by any foreign objects.
.For safe driving;
Keep the sound low enough to enable you to hear outside sound when driving.
Do not exchange the CDs, adjust the volume, nor any other operation which dis-
turbs your safe drive, when driving.
.When not using the unit, do not forget to remove the CD. Do not leave the ejected
CD sitting on the edge of the unit for along time. This can expose the CD to direct
sunlight and other causes of warping. Keep the disc away from direct sunlight.
.This unit plays an 8 cm CD just like a 12 cm CD without an adapter. Do not use an
8cm CD Adapter. Using a8cm CD Adapter will result in amal function.
.Temperature
The unit may not operate correctly in extremely hot or cold temperature. If this
should happen, stop using the unit untill the temperature becomes normal.
The unit is equipped with abuilt in self protection circuit. When the temperature
inside the unit goes above the reference temperature, the protection circuit auto-
matically stops the play and ejects the CD. In this case, open the window to cool
off the car, then start up the unit again.
.Condensation
Moisture can condense on the optical lens of the unit during rainy and humid days,
or right after the heater is turned on in the car. If this should happen, the unit can-
not read the CD and therefore cannot function properly.To remedy the situation,
remove the CD from the unit and wait untill the condensation evaporates (approxi-
mately one hour).
3

●sound skip
When you are driving on a rough road, sound may sometimes be skipped. It is
inevitable and will not cause any damage, disc scratch, e.t.c.
●Cleaning n
Do not attempt to clean the unit with chemical solvents as this might damage the ~
finish. Use aclean, dry cloth. CD
~
CD
c
(n
CD
Handling the CDs
Dirt, dust, scratches and warpage cause sound skips during playback and a deterio-
ration of sound quality. How to take care of your discs:
■Use compact discs that have the mark shown on the right.
dr!~
DIGITAL AUDID
■Fingerprints and dust should be carefully wiped off the disc’s signal surface (glossy
side) with asoft cloth. Unlike conventional records, the compact disc has no
grooves to collect dust and microscopic debris, so gently wiping with asoft cloth
should remove most particles. Wipe in astraight motion from the inside to the out-
side of the disc. Small dust particles or light stains will have absolutely no effect on
reproduction quality.
■Never use such chemicals as record sprays, antistatic sprays or fluids, benzine or
thinner to clean compact discs. Such chemicals would irreparably damage the
disc’s plastic surface.
■Disc should be put back in their cases after use to avoid serious scratches that
could cause the sound skip.
■Do not expose discs to direct sunlight, high humidity, or high temperatures for
extended periods of time. Long exposure to high temperatures can warp the disc.
■Do not stick paper or write anything with aball-point pen on the disc surface.

Location and function of control
(General operation)
@Audio control mode select button @Audio control button
@Display select button Clock adjust button
@Loudness button @On/Off button
@Display
@@Eiim
@Disc slot
@Track/ Skip button
@l Eject button
@CD mode select button
Play/Pause button
Radio operation
@Auto travel preset button
@LO /DX button
@Tuning button
Changer operation_)
@Changer select button
@Track /Skip button
@Changer mode select button
Play IPause button
@-@Disc select buttons
@Shuffle button
@Scan button
@Repeat button
@JRadio mode select button
Band select button
@-@preset buttons
@Shuffle button
@Scan button
@Repeat button
5

Digital display
@Changer No. indicator (Changer)
@Auto travel preset indicator (Radio)
ODisc set indicator (CD)
@Loudness indicator (Radio)
@This indicator appears during Disc
Scan /Disc Repeat/ Disc Shuffle
operation. (Changer)
@Scan indicator (CD/ Changer)
@Repeat indicator (CD/ Changer)
@Shuffle indicator (CD/ Changer)
@DX indicator (Radio)
@Stereo indicator (Radio)
0Playing indicator (CD/ Changer)
@●Audio level (Audio control)
.Disc No. (CD /Changer)
●Preset No. (Radio)
GAM band indicator (Radio)
(@FM band I /II indicator (Radio)
@.Audio mode
[VOL/BAS/lRE/BAL/FAD]
(Audio control)
sClock
.Track No. (CD /Changer)
.Frequency (Radio)
@.This indicator flashes on every I
second. (Clock)
.This indicator stands for “50 kHz”.
(FM band of Radio)

Power On/ Off
CD mode select button -1
~On /Off button Changer mode select button ~
Radio mode select button ~
To turn on the unit m,!_vJq).
Press one of the following mode select buttons (HI
n
●To play aCD ;Press CD mode select button (R). QSee page 12.
(A CD must be inserted in the unit.)
I_.--J
●To listen to the radio ;Press Radio mode select button (2). 0See page 14.
●To operate CD Changer; Press Changer mode select button (~). QSee
page 17.
(An optional SANYO CD Changer, FXD-C300 (1O-disc), FXD-C600 (6-disc) or
FXD-C100 (6-disc) must be connected.)
Notes:
●You can turn on the unit by pressing the On /Off button (B), too. In this
case, the mode (CD /Radio /Changer) is the selected one before you turned it off.
●When you insert aCD into the Disc slot, CD play will start automatically.
●Press the mode select button of your desired mode to switch immediately to the
mode.
To turn off the unit
Press the On /Off button (@@).

Audio Control
rAudio control mode select button
_Loudness button
—Audio control button
●VOL (Volume) control
Press the (~\) side of the Audio control button to increase, or the (~) side to
decrease the volume level. During adjustment, [VOL] appears on the display.
●BAS (Bass) /TRE (Treble) /BAL (Balance) /FAD (Fader) control
@Pressing the Audio control mode select button (~), select the desired mode.
With each press the mode shifts to the next setting. See below.
@Pressing the (~\ )or (~)side of the Audio control button, adjust the level.
Note:
.Adjust the Bass, Treble, Balance or Fader within 5seconds after selecting
the Audio control mode (the selected mode indicator appears on the display),
If no mode indicator appears on the display, pressing the (~\) or (~)
side of the Audio control button will adjust the volume.
Hint:
●Press and hold the audio control button to change the level quickly.
Mode shift ‘ress u“Press ~\. Display
7To decrease
B~S (Bass) To increase -7-7
T~E (Treble) To decrease To increase –7-7
BAL (Balance) To the left speaker To the right speakers o-9
F~D (Fader) To the rear speaker To the front speakers o-9
IV+OL (Volume) I I
To decrease To increase 0-19
Note:
●With each press, the level changes. But the Audio level shown on the display
does not change with every press. Use it to know the rough level.
●Loudness (LOUD) a
Press the Loudness button (,.,O, )to emphasize the Bass and Treble range at low
listening level. [LOUD] appears on the display. To cancel the mode, press the but-
ton again.
8

Selecting aprior display
You can choose Clock display or Mode display as prior display.
When you choose Clock display, time is shown on the display at all times.
When you choose Mode display, the display corresponds to the current mode
Radio /Changer).
~Display select button
(CD I
~. preset button 3
How to select o
While holding down the Display select button (DISP ), press the Preset button 3
(=). With each press, the prior display shifts
Notes:
●While adjusting the audio, the audio level is shown.
.When the volume level is “O’; [0 VOL] is shown.
To show the other display for amoment
Press the Display select button (~, ). The other display will be shown for about 5
seconds.

Clock operation
The
play following operations are effective while the power is on. Though the Clock dis- is shown when the power is off, you can not adjust nor set the time.
r— Display select button
I~Audio Control mode select button
‘Clock adjust button
To adjust the time
1. See that the Clock display is shown.
Hint: o
●If the Clock display is not shown, press the Display select button (~l~P)to
show the Clock display for amoment (about 5seconds).
2. While holding down the Display select button (9P ), press the (~\) or(~)
side of the Clock adjust button.
To set hour digits :Press (~\) side.
TO set minute digits :Press (~) side.
Hint:
.Press and hold the button to advance the time quickly.
Notes:
.This is a12-hour clock.
●The clock setting is retained when the power is turned off.
To set the time to the nearest half-ho~r
While holding down the Display select button (~P ), press the Audio control mode
select button (@).
The time is set as follows:
EX.lO:OO -10:29 O10:00
10:30-11:00 d11:00
10

How to load, play, remove aCD
Disc slot ~Eject button ~
e’abe’side
How to load and play aCD
1.Insert aCD into the Disc slot with the label side facing up.
The Disc set indicator [DISC IN] will appear and CD play will begin.
Notes:
.When you insert adisc, make sure that the label side is up. If the CD is placed
upsidedown, [E: 07] will appear and the unit will eject the CD automatically.
●Do not insert another CD when the Disc set indicator [DISC IN] is shown.
Because the Disc slot can accommodate only one CD.
.You can not insert aCD when the ACC is off.
.Do not use an 8 cm CD Adapter. The unit plays 8cm CD just like a 12 cm CD
without an adapter.
2. Adjust the volume and tone quality. (See page 8 “Audio control”.)
Hint:
●After the whole CD has been played, play will start again from the beginning of
the first track.
How to remove aCD
Press the Eject button (~ ).
Hints:
●When you insert the CD into the Disc slot again, play starts from the beginning of
the first track.
●When you turn on ACC after having turned it off during CD play, the unit starts CD
play from the point at which you stopped the play by turning ACC off.
11

CD mode select button, Pause, Selecting atrack, Skipping
CD mode select button
Play /Pause button 1
Track /Skip button J
CD mode select button
n
Press the CD mode select button (~)to switch immediately to CD mode from
other mode (Radio, Changer, Power off mode).
Note:
.This button is not effective when aCD has not been inserted in the unit.
Pause
II
Press the Play/Pause button (fi )during CD play to stop CD play temporarily.
To resume play from the point at which play was stopped, press the button again.
Note:
●If the unit is left in the Pause mode for more than 5minutes, the power will switch
off automatically.
Selecting atrack o
Pressing the (+)or (m)side of the Track/ Skip button (‘*’C’*), select atrack.
Skipp
Desired Track Press this side.
Next Track m
Current Track
(from the beginning) +4
Preceding Track +(twice successively)
lng o
Press and hold the (44 )or (w)side of the Track/ Skip button (‘SEEK*)for 1.5
seconds or more to advance quickly in the forward or backward direction. When the
button is released, this function stops
Note:
When it reaches to the end or the beginning of the disc, the unit enters Pause mode.
12

Scan, Repeat, Shuffle
d]
Shuffle button ~
Scan bution
Repeat button
Scan
Press the Scan button ( - ) to play the first 10 seconds of each track.
To cancel the mode, press the button again, or the unit continues Scan play endlessly.
Repeat
Press the Repeat button (/-1) to repeat the track currently playing.
To cancel the mode, press the button again, or the unit continues Repeat play end-
lessly.
Shuffle
Press the Shuffle button (H)to play the tracks on the disc in random order.
When all the tracks have been played, they will be played again in adifferent order.
To cancel the mode, press the button again, or the unit continues Shuffle play end-
lessly.
13

How to turn on the radio and select aband, Tuning
Radio mode select button
Band select button —
Tuning button J
How to turn on the radio and select aband
D
1. Press the Radio mode select button (1~ )to turn on the radio.
2. Adjust the volume and tone quality. (See page 8 “Audio conrol”.)
3. Pressing the Band select button (H), select the desired band.
With each press, the band shifts as follows.
FM1 +FM2 +AM
Tuning ............... There are 2types as follows.
1
2
Auto (Seek) tuning ......The unit will tune Up or down in frequency and stop on
the next strong station. (The tuning normally operates in
the auto mode.) o
Pressthe(+)
or (~)side of the Tuning button (‘S””* ).
To tune up Press the (~)side for less than 0.7 seconds.
To tune down Press the (<)side for less than 0.7 seconds.
Manual tuning .. With each press, the frequency will shift up or down by
50 kHz (FM) or 9kHz (AM). o
Press and hold the (~)or (~)side of the Tuning button (‘s’’’” )for 0.7 sec-
onds or more to switch to the manual tuning mode. The frequency indicator will
flash on and off.
Note:
It returns to Auto (Seek) tuning mode if the Tuning button is not pressed within 5
seconds after it becomes Manual tuning mode. o
pressthe(+)
or (~)side of the Tuning button (“’’’” )when the frequency
indicator flashes on and off.
~
Hint:
.Press and hold the button to chanae the freouencv auicklv.
,,, .
14

LO/ DXbutton,Radiomodeselectbutton, Presettingstations
LO I
Auto travel preset button Radio mode select button————
DX button (Selecting seek sensitivity of Auto tuning)
Press the LO/ DX button (=)for 1.5 seconds or more to select the desired seek
sensitivity.
With each press, [DX] indicator appears and disappears.
To receive local stations with strong signals, make the [DX] indicator disappear.
To receive distant stations with weaker signals, make the [DX] indicator appear.
Radio mode select button
D
Press the Radio mode select button (4)to switch immediately to Radio mode
from other mode (CD, Changer, Power off mode).
presetting StZItiOI’IS ...... . ... There are 2types as follows.
Manual preset ............. 6Staticms can be preset cm each band (FMI, FM2, AM).
How to preset
1. Select the desired band (FMI, FM2, AM) and tune to the station to be memo-
rized.
2. Press the desired preset button for 1.5 seconds or more.
3. To preset additional stations, repeat procedure 1 and 2.
How to recall
Select the desired band and press the desired preset button.
Auto travel preset .........The unit will scan the selected band (FM or AM) and
memorize the 6strongest stations.
How to preset
1. Select the desired band (FM or AM).
2. Press the Auto travel preset button (~)untill the [– –– ]indicator appears
(for about 1.5 seconds). The indicator [ATP] will flash on and off. The unit will
scan the band for the strongest 6stations and automatically memorize them.
Scanning will stop and the first memorized station will be heard.
Notes:
●/f ail stations are weak, none maybe memorized. If this should occur, [000] will
appear on the display. The station received last will be selected.
. If there are fewer than 6receivable stations, the unit will memorize all the receiv-
able stations, then the first memorized station will be selected.
15

How to recall
Select the desired band and press the Auto travel preset button (@)for less
than 0.5 seconds. Each time the button is pressed, the remaining ATP station will
be selected in the order they were memorized.
Before operation
Preparation
1. According to this manual, connect acompatible SANYO CD Changer (FXD-C300,
FXD-C600, FXD-CIOO) to this unit.
2. According to the manual of CD changer, load discs into magazine and install the
magazine to the CD changer.
Hint:
●You can connect asecond CD Changer. (See below. “Changer select button’~
Changer select button
Using aseparately available SANYO Divider unit
Changer select button
e
(FTP-CH1 S), asecond CD Changer can be connect-
ed. When you connect two CD Changers, select the
[
desired CD Changer with this button. With each
+‘“1 **
E
press, the Changer No. indicator [@I ,@~]
&???Q’ changes.
r-mm —
Notes:
.According to the manuals of CD changers and Divider unit, set the ID switches of
CD changers beforehand.
.This button is not effective when only one CD changer is connected.
CD Changer 1(@I)
CDF-R800
CD Changer 2(@rI)
16

How to play CDs, Pause, Selecting adisc /track
Acompatible SANYO CD Changer must be connected.
Changer mode select button
Play /Pause button
‘L’
\
+“3 a
$;Qp[~j’””eg
\2 ~+lm mu SCN ~
i,1
.
Disc select button Track ISkip button
How to play CDs @
1. Press the Changer mode select button (.1, )to switch immediately to Changer
mode from other mode (Radio, CD, Power off mode ).
2. Adjust the volume and tone quality. (See page 8 “Audio control”.)
Hint:
.When the CD Changer is used for the first time, or when the CD magazine has
been changed, p/ay will begin from the first track of the first disc.
Pause m
Press the Play /Pause button (.ll )during play to stop the play temporarily.
To resume play from the point at which play was stopped, press the button again.
Note:
. If the unit is left in the Pause mode for more than 5minutes, the power will switch
off automatically.
Selecting adisc
Press one of the Disc select buttons (~\, ~~ )to select adisc.
=
Selecting atrack o
Pressing the (~)or (>)side of the Track/Skip button (““K* ), select atrack.
Desired Track Press this side.
Next Track w
Current Track
(from the beginning) +4
Preceding Track *(twice successively)–
17

Skipping, Scan, Repeat, Shuffle
Acompatible SANYO CD Changer must be connected.
Track /Skip button -1
p-=\rT-T\r\ /4.5HF//5.5CN//6Sf
.+
d]
Shuffle button ~
Scan button
Skipping Repeat button oB
Press and hold the (+)or (~)side of the Track/Skip button (““K*) for 1.5 sec-
onds or more to advance quickly in the forward or backward direction. When the but- ~
ton is released, this function stops.
=i.
Note: o
When it reaches to the end or the beginning of the disc, the unit enters Pause mode. o
Scan
Press the Scan button (m) to play the first 10 seconds of each track on the cur-
rently selected disc. To cancel the mode, press the button again, or the unit contin-
ues Scan play endlessly.
Note:
Be sure to press the bution for less than 1.5 seconds when you cancel the mode, or
Disc Scan will begin.
Repeat
Press the Repeat button (~) to repeat the track currently playing. To cancel the
mode, press the button again, or the unit continues Repeat play endlessly.
Note:
Be sure to press the button for less than 1.5 seconds when you cancel the mode, or
Disc Repeat will begin.
Shuffle
Press the Shuffle button (~) to play the tracks on the currently selected disc in
random order. When all the tracks have been played, they will be played again in a
different order. To cancel the mode, press the”bu~on again, or the u~t continues
Shuffle play endlessly
Note:
Be sure to press the button for less than 1.5 seconds when you cancel the mode,
Disc Shuffle will begin. or
18

Disc Scan, Disc Repeat, Disc Shuffle
Acompatible SANYO CD Changer must be connected.
[
F=irrrr\m-\ .-
Shuffle button -J I I
Scan button ~I
nDisc Scan
Repeat button ~
!3 Press the Scan button (/-) for 1.5 seconds or more to play the first 10 seconds
$of the first track on each disc.
:To cancel the mode, press the button again, or the unit continues Disc Scan play
~endlessly.
~-
0
=Disc Repeat
Press and hold the Repeat button (/={) for 1.5 seconds or more to repeat the disc
currently playing.
To cancel the mode, press the button again, or the unit continues Disc Repeat play
endlessly.
Disc Shuffle
Press the Shuffle button (-) for 1.5 seconds or more to select adisc at random
and play all the tracks on the disc in random order. When all the tracks have been
played, the next disc is selected at random and all the tracks on that disc are played
in random order. The unit repeats this procedure endlessly.
To cancel the mode, press the button again.
19