Sanyo VCC-9684VA - 1/4" Color CCD Indoor Mini Dome... User manual

FILE NO.
REFERENCE No.SM5310726
L5CJ2/XE, XE-C1F, US, US-C1F (R)
NOTE: 1. Parts order must contain model number, part number, and description.
2. Substitute parts may be supplied as the service parts.
3. N.S.P. : Not available as service parts.
Design and specifications are subject to change without notice.
SERVICE MANUAL
Color CCD Camera
VCC-9684VA
(Product Code : 117 168 01)
(Product Code : 117 238 01)
(U.S.A., Canada, Brazil, Taiwan)
The components designated by a symbol ( ! ) in this schematic diagram designates components whose value are of
special significance to product safety. Should any component designated by a symbol need to be replaced, use only the
part designated in the Parts List. Do not deviate from the resistance, wattage, and voltage ratings shown.
PRODUCT SAFETY NOTICE
VCC-9685VP
(Product Code : 117 168 00)
(Product Code : 117 238 00)
(Europe, U.K., Southeast Asia)
CONTENTS
1. DISASSEMBLY ...............................3
2. ADJUSTMENT ................................6
3. PARTS LIST .................................10
CIRCUIT DIAGRAMS &
PRINTED WIRING BOARDS .......... C1
Scanning system : PAL standard 625 lines, 50 fields/sec. (VCC-9685VP)
Scanning system : NTSC standard 525 lines, 60 fields/sec. (VCC-9684VA)
Image sensor : 1/4" interline transfer method CCD
Number of effective pixels : 752 (Horizontal) x 582 (Vertical) (VCC-9685VP)
Number of effective pixels : 768 (Horizontal) x 494 (Vertical) (VCC-9684VA)
Horizontal resolution : 540 TV lines, typical
Minimum illumination (approx.) : 0.5 lx ( F0.95)
Video output : 1.0 V (p-p)/75 ohms, composite, BNC
Video output : UTP support (VA-10T: option board)
Video S/N ratio : More than 48 dB (AGC off: More than 50 dB)
Vari-focal lens : f = 2.8 - 8 mm (F = 0.95 - 1.7)
Rotation range : (On the ceiling) Pan: ± 100 degrees, Tilt: 0 - 90 degrees
Rotation range : (On the wall) Pan: ± 90 degrees, Tilt: 0 - 90 degrees
Backlight compensation : OFF, Multi-spot metering (High/Normal), Center zone
metering
White balance : ATW/Manual
Electronic shutter : 1/50, 1/120, 1/1000, 1/2000 sec. (VCC-9685VP)
Electronic shutter : 1/60, 1/100, 1/1000, 1/2000 sec. (VCC-9684VA)
Aperture compensation : Sharp/Normal
Sync system : Internal sync/Line-lock
Operating environment : Temperature -10°C - +50°C (14°F - 122°F)
Operating environment : Humidity less than 90% RH (no condensation)
Power supply : 24 VAC ± 10% (50 Hz for VCC-9685VP, 60 Hz for VCC-9684VA),
12 - 15 VDC
Power consumption (approx.) : 2.4 W
Weight (approx.) : 500 g (16 oz.)
SPECIFICATIONS
RoHS
This product does not contain any hazardous substances prohibited by the RoHS Directive.
WARNING
You are requested to use RoHS compliant parts for maintenance or repair.
You are requested to use lead-free solder.
(This product has been manufactured using lead-free solder. Be sure to follow the warning given on page 2 when carrying
out repair work.)

-2 -
WARNING
Do not use solder containing lead.
This product has been manufactured using lead-free
solder in order to help preserve the environment.
Because of this, be sure to use lead-free solder when
carrying out repair work, and never use solder
containing lead.
Lead-free solder has a melting point that is 30 - 40°C (86 -
104°F) higher than solder containing lead, and moreover it
does not contain lead which attaches easily to other metals.
As a result, it does not melt as easily as solder containing
lead, and soldering will be more difficult even if the
temperature of the soldering iron is increased.
The extra difficulty in soldering means that soldering time
will increase and damage to the components or the circuit
board may easily occur.
Because of this, you should use a soldering iron and
solder that satisfy the following conditions when carrying out
repair work.
Soldering iron
Use a soldering iron which is 70 W or equivalent, and
which lets you adjust the tip temperature up to 450°C
(842°F). It should also have as good temperature recovery
characteristics as possible.
Set the temperature to 350°C (662°F) or less for chip
components, to 380°C (716°F) for lead wires and similar,
and to 420°C (788°F) when installing and removing shield
plates.
The tip of the soldering iron should have a C-cut shape or
a driver shape so that it can contact the circuit board as flat
or in a line as much as possible.
Solder
Use solder with the metal content and composition ratio by
weight given in the table below. Do not use solders which
do not meet these conditions.
Lead-free solder is available for purchase as a service tool.
Use the following part number when ordering:
Part name: Lead-free solder with resin (0.5 mm dia., 500 g)
Part number: VJ8-0270
Metal content Tin (Sn) Silver (Ag) Copper (Cu)
Composition
ratio by weight 96.5% 3.0% 0.5%
Note:
If replacing existing solder containing lead with lead-free
solder in the soldered parts of products that have been
manufactured up until now, remove all of the existing solder
at those parts before applying the lead-free solder.

-3 -
1. DISASSEMBLY
1-1. REMOVAL OF COVER, CABINET AND BOARD LOCATION
1. Pushing the cabinet top
2. Dec cover
3. Screw 3 x 6
4. Spacer sheet inner
Start affixing the sheet from
the center of the mark on
the cover inner.
5. Cover inner
6. Cabinet top
7. Pushing the button slide
8. Screw 3 x 6
9. Screw 3 x 6
10. Screw 3 x 6
11. Special washer
12. Pipe
13. Two screws 3 x 6
14. Two special washers
15. Two pipes
16. Arm. tilt
CA-1 board
VA-10T
(OPTION)
CA-3 board
CA-2 board
CA-4 board
4
1
5
2
3
h
su
P
6
7
9
10
11
15
13
13
16
12
14
14
15
8

-4 -
20
24
22
23
25
5
1
2
3
4
6
8
9
10
7
11
13
12
14
16
17 18
15
19
21
19
1. Screw 3 x 6
2. Stopper wheel
3. Spring wheel
4. Bearing support wheel
5. Arm pan
6. Four screws 2 x 4
7. CA-4 board
8. Screw 3 x 12
9. Washer Z
10. Pipe
11. Three screws 4 x 6
12. Screw 3 x 4
13. Fixer
14. Shassis base
15. Screw 3 x 6
16. Holder safety
17. Earth
18. Cabinet bottom
19. Three screws 2 x 4
or 2 x 6 (With option board)
20. VA-10T (Option board)
21. Screw 2 x 4
22. Cover button
23. Button slide
24. Spring
25. Holder base
1-2. REMOVAL OF CA-4 BOARD, CABINET BOTTOM AND HOLDER BASE

-5 -
1
2
3
4
7
6
5
8
10
9
11
12
13
13
16
18
17
14
15
1. Wssy wire (W4003) CN304
2. Two screws 2 x 4
3. CA-3 board
4. Connector CN302-CN203
5. Two screws 2 x 4
6. CA-2 board
7. Connector CN201-CN102
8. Two screws 2 x 6
9. CCD
10. Spacer CCD
11. Optical filter
12. Lens (assy)
13. Four screws 2 x 4
14. Shassis PWB
15. Screw 2 x 4
16. CA-1 board
17. Spacer insulator
18. Mounting CCD
1-3. REMOVAL OF CA-3 BOARD, CA-2 BOARD AND CA-1 BOARD

-6 -
2. ADJUSTMENT
2-1. ADJUSTMENT CONDITION
1. Use the 5,100K viewer for the subject.
2. Set the trigger signal of oscilloscope to VIDEO OUT, and
apply H sync unless specified.
3. Set each of the S1001 (CA-1) switches to the all OFF
position.
4. In adjustments without direction to display charts, shield
light with a lens cap to provide dark condition.
5. Connect the video output to a video monitor with an input
impedance of 75 ohms.
6. The video monitor should be an under-scan TV.
2-2. TABLE FOR SERVICING TOOLS
2-3. PREPARATION
1. Install the adjustment software (VHJ-0189) in a computer
running the Windows operating system.
2. Use the adjustment tool (VHJ-0127) to connect the
camera to be adjusted to the serial port (COM1) of the
computer with RS-232C cross cable (
Inter link cross cable,
VHJ-0149), and then turn on the power for the computer .
3. Double-click the adjustment software which has been
installed into the computer.The main window will be
displayed.
4. Click “Adjustment” in the main window menu and click
“L5BG/CJ”. The main dialog window will be displayed.
5. In the main dialog window, click “SET UP”. The setup
window will be displayed.
6. In the setup window, change all other values to the
standard settings (setup window illustration).
7. Click “OK” to accept the settings. The main dialog
window will be displayed.
8. In the main dialog window, click “ADJUSTMENT”. The
adjustment window will be displayed.
9. In the adjustment window, click “START”.
2-3-1. Adjustment parts position
2-3-2. Computer screen during adjustment
Ref. No. Name Part code
J-1
J-2
J-3
J-4
J-5
J-6
J-7
VJ8-0007
VJ8-0009
VJ8-0010
VHJ-0126
VHJ-0127
VHJ-0149
VHJ-0188
Color viewer
Color bar chart
Gray scale chart
Commander cable (spare)
Adjustment jig
Inter link cross cable
Calibration software
VR103 VR102
VR101 VR104
TP101 GND
S1001
TP211CT221 TP232
CT231 CN205
CA-1 board Side A
CA-2 board Side A CA-2 board Side B
R V X Z H W AF AG AX AY BC BG BH BU I Co
dspcctv - DSP Camera Control for Windows95/98/Me/2000 Ver.
Exit Adjustment Set View Help
DSP
CAM
Ready
NUM
L53R
L53V
L53X
L53Z
L53H
L54W
L5BG/CJ
R V X Z H W AF AG AX AY BC BG BH BU I Co
dspcctv - DSP Camera Control for Windows95/98/Me/2000 Ver.
Exit Adjustment Set View Help
DSP
CAM
Ready
NUM
L5BG
MODEL
ADJUSTMENT ADD
SETUP COPY
DEL
CLOSE
Main window
Main dialog window

-7 -
SET L5BG
ADJ/CHK INIT DATA
MODEL
ADJUSTMENT
ROM CLEAR
SYNC
BURST
A.IRIS
M/WB
127
127
127
127
AGC OFF
WDD THRESHOLD 100
NORMAL
Day/Night Mode
B/W
COLOR
OK CANCEL
Y GAIN
CROMA
Set Exposure
8
80
WDD GAIN
SCROLL TIMER mS
50
127
127
127
SET VERSION(BACK)
SET VERSION(FRONT)
65
LENS DATA
10
ROMCLEAR TIMER Sec
L5CJ
*****
********
ADJ L5BG
START END
CLOSE
MODEL
STATUS
TACT
Version(BACK)
R GAIN
R HUE
B HUE
0
0
0
SYNC
BURST
0
0
A.IRIS
M/WB
0
B GAIN
AUTO
WDD
AGC OFF
Version(FRONT)
Y GAIN 0
2-4. Sub Carrier Frequency Adjustment
Adjustment location: CT221 (CA-2)
Measuring location: TP211 (CA-2)
Measuring equipment: Frequency counter
Subject: No designation
Adjusting method:
1. Adjust with CT221 to 4433619 Hz ± 10 Hz (VCC-9685VP)
or 3579545 Hz ± 10 Hz (VCC-9684VA).
2-5. 28 MHz VCO Voltage Adjustment
Adjustment location: CT231 (CA-2), S1001 (CA-1)
Measuring location: TP232 (CA-2)
Measuring equipment: Digital voltmeter
Subject: No designation
Adjusting method:
1. Set S1001-7 switch to the “INT” (OFF) position.
2. Adjust with CT231 to 5.0 ± 0.2 V.
2-6. SYNC and BURST Level Adjustment
Adjustment location:
Measuring location: VIDEO OUT
Measuring equipment: Oscilloscope
Subject:
Adjusting method:
1. Shield light with a lens cap to provide dark condition.
2. Click the adjustment software installed from the personal
computer, and the adjustment window will be displayed.
3. Click the START.
4. Use the computer’s mouse to adjust the SYNC in the
adjustment window so that the video out terminal is 300 ± 5
mVp-p (VCC-9685VP) or 286 ± 5 mVp-p (VCC-9684VA).
5. Use the “ ” button to be BURST in the adjustment window.
6. Use the computer’s mouse to adjust the BURST in the
adjustment window so that the video out terminal is 300 ±
5 mVp-p (VCC-9685VP) or 286 ± 5 mVp-p (VCC-9684VA).
VIDEO OUT
300 mV ± 5 mV
or
286 mV ± 5 mV
sync
burst
300 mV ± 5 mV
or
286 mV ± 5 mV
Set up window
Adjustment window

-8 -
2-8. Hue and Chroma Adjustment
Adjustment location: Computer screen
Measuring location: VIDEO OUT
Measuring equipment: Oscilloscope, vectorscope
Subject: Color bar chart
1. Use the “ ” button to be R GAIN in the adjustment window.
2. Shield light with a lens cap to provide dark condition.
3. Select the R GAIN and B GAIN by using the “ ” and “ ”
button in the adjustment window.Adjust by operating level
scroll bar so that the red and yellow luminescent spots are
the size and position which are designated in the vectorscope.
4. Select the R HUE and B HUE by using the “ ” and “ ”
button in the adjustment window. Adjust by operating level
scroll bar so that the red and yellow luminescent spots are
the size and position which are designated in the vectorscope.
2-7. White Balance Adjustment
Adjustment location: VR102, VR104 (CA-1)
Measuring location: VIDEO OUT
Measuring equipment: Oscilloscope, Vectorscope
Subject: Color bar chart
Adjusting method:
1. Use the “ ” button to be A. IRIS in the adjustment window.
2. Auto iris adjustment will be started automatically.
3. Use the “ ” button to be MANUAL WB in the adjustment
window.
4. Display the color bar chart at designated picture angle.
5. Adjust VR102 and VR104 so that the luminescent spot rep-
resenting white is overlapping with the crosshair mark in
the center of the vectorscope.
45 µsec
R
Y
L
M G
C Y
G
B
Q
100%
75% W
R
YL
MG
Cy
G
B
75%
100%
cy
g
yl
mg
b
U
v
W
VCC-9685VP
VCC-9684VA
45 µsec
R
Y
L
M G
C Y
G
B
Q
100%
75%
YL R
R
YL
MG
Cy
G
B
75%
100%
cy
g
yl
mg
b
U
v
YL R
W
VCC-9685VP
Adjustment value
R :614mV 107°
YL:476mV 160°
VCC-9684VA
Adjustment value
R :575mV 107°
YL:440mV 160°

-9 -
2-9. Y-Gain Adjustment
Adjustment location: Computer screen
Measuring location: VIDEO OUT
Measuring equipment: Oscilloscope
Subject: Gray scale chart
Adjusting method:
1. Display the gray scale chart at designated picture angle.
2. Use the “ ” button to be “ “GAIN in the adjustment window.
3. Shield light with a lens cap to provide dark condition.
4. Use the computer’s mouse to adjust the Y GAIN in the ad-
justment window so that the video out terminal is 700 ± 10
mVp-p.
2-10. Iris Level Adjustment
Adjustment location: S1001, VR103 (CA-1)
Measuring location: VIDEO OUT
Measuring equipment: Oscilloscope
Subject: Gray scale chart
Adjusting method:
1. Set S1001-4 and 5 switches to the OFF position.
2. Use the “ ” button to be AGC OFF in the adjustment window.
3. Display the gray scale chart at designated picture angle.
4. Turn the VR103 to the right so that the white level is maximum.
5. Turn the VR103 to the left so that the output level is 700 ±
10 mVp-p.
VIDEO OUTPUT
700 mV ± 10 mV
35 µsec
2-11. CCD White Point Defect Detect Adjustment
Measuring location: VIDEO OUT
Measuring equipment: Monitor display
Adjustment method:
1. Shield light with a lens cap to provide dark condition.
2. Use the “ ” button to be WDD in the adjustment window.
3. Click the AUTO button.
4. After completing the CCD White Defect Detect adjustment,
it comfirms that white point can not be seen on the monitor
display.
5. Click the END button.
2-12. Line Phase Adjustment
Adjustment location: S1001, VR101 (CA-1)
Measuring location: VIDEO OUT, 24 V AC/GND terminals
Measuring equipment: Oscilloscope
Adjusting method:
1. Connect the camera to a 24 V AC /50 Hz (VCC-9685VP) or
(VCC-9684VA) 60Hz power source.
2. Set S1001-7 switch to the “LL” (ON) position.
3. The HOT (signal) side and the COLD (GND) side of the
oscilloscope probe connect to the right side and the left side
of the 24 VAC terminals respectively. (rear view)
4. Turn VR101 (LINE PHASE) to adjust the leading edge of
the vertical sync signal and zero-cross shift of the AC 24 V
power supply to 0 ± 0.2 msec.
5. Set S1001-7 to the “INT” (OFF) position before shipment.
VIDEO OUTPUT
700 mV ± 10 mV
35 µsec
0 ± 0.2 msec.
VIDEO OUT
24 V AC zero cross point

10
3. PARTS LIST (R)
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
ACCESSORIES & PACKING MATERIALS
9110 613 215 1597 INST MANUAL A5,English,VCC-9684VA ONLY
9110 613 215 1627 INST MANUAL A5,English,French,
VCC-9685VP ONLY
9111 613 215 1610 INST MANUAL,German A5,Chinese (Simplified),
VCC-9685VP ONLY
9111 613 215 1603 INST MANUAL A5, French,Spanish,
VCC-9684VA ONLY
9303 411 098 1303 SCR S-TPG BIN 3X6A
9001 613 211 5865 CARTON CASE INNER
9002 613 209 3316 CUSHION,TOP
9003 613 209 3323 CUSHION,BOTTOM
9004 613 209 4719 CUSHION,BOTTOM-UPPER
9005 613 209 4726 REINFORCEMENT,PAD
9006 613 209 8267 REINFORCEMENT,PAD-BOTTOM
CABINET & CHASSIS PARTS
5001 613 208 7513 CABINET TOP
5002 613 208 7605 DEC COVER
5003 613 208 7599 COVER INNER
5004 613 210 1790 SPACER SHEET INNER
5009 613 210 6047 HOLDER BASE
5010 613 208 7582 COVER BUTTON
5011 613 208 7568 BUTTON SLIDE
5012 613 208 7629 SPRING
6002 613 201 0016 PIPE
6321 613 210 6245 SPACER,INDICATOR-L5BL
6410 613 214 9013 ARM, TILT-L5CJ2
NJ500 411 192 1308 S-TPG BIN 3X61
NJ515 411 214 8308 SCR S-TPG BIN 2X4
NJ620 411 197 2607 SCR BIN 3X6
NJ621 411 031 8604 SCR BIN 3X6
NJ645 312 057 3805 SPECIAL WASHER 43X0.2
Note : #2 is written on page 12.
#1
6001 613 214 8993 CHASSIS,PWB-L5CJ2
6007 613 214 9020 MOUNTING,CCD-L5CJ2
6008 613 214 9044 SPACER,CCD-L5CJ2
6009 613 214 9037 SPACER,INSULATOR-L5CJ2
6010 613 215 8671 COVER,PWB-L5CJ2
8000 645 095 3804 LENS(ASSY)
8001 645 095 3699 OPTICAL FILTER
IC101 309 514 9302 IC ICX228AK-A,VCC-9684VA ONLY
IC101 309 514 9401 IC ICX229AK-A,VCC-9685VP ONLY
CA1 613 214 7309 COMPL PWB,CA-1
CA2 613 214 8146 COMPL PWB,CA-2 F/W,VCC-9685VP ONLY
CA2 613 215 1368 COMPL PWB,CA-2 F/W,VCC-9684VA ONLY
CA3 613 214 7361 COMPL PWB,CA-3
NJ601 411 030 5406 SCR BIN 2X4
NJ610 411 191 1804 SCR S-TPG BIN 2X6

11
5004
5003
5002
NJ500 NJ620
NJ621
6002
NJ621
NJ621
6410
6002
NJ645
NJ645
NJ645
6002
L5CJ2-1
NJ620
5012
5010
5011
5009
NJ515
NJ515
#2
#1
5001
6321
NJ601
CA3 CA2
NJ601
NJ610
6008
8001
8000
IC101
NJ601
CA1
6007
6009
6001
NJ601
6010
#1
CABINET & CHASSIS PARTS

12
LOCATION PARTS NO. DESCRIPTION
#2
5005 613 208 7520 CABINET BOTTOM
5006 613 208 7643 EARTH
5007 613 211 9948 HOLDER SAFETY
5016 613 215 1672 LABEL CABLE-L5CJ2
5018 613 184 2717 LABEL,CAUTION(US),VCC-9684VA ONLY
5019 613 215 1689 LABEL SWICH-L5CJ2
6003 613 215 7070 PIPE,H6
6005 645 070 9760 FIXER CLAMP
6006 645 093 1147 FIXER,L45(NON-PVC)
6040 613 214 8986 CHASSIS,BASE-L5CJ2
6050 645 041 0314 FIXER,14.2X19.6
6420 613 214 9006 ARM, PAN-L5CJ2
6470 613 209 3248 STOPPER,WHEEL
6480 613 209 3200 SPRING,WHEEL
6490 613 209 3187 BEARING,SUPPORT WHEEL
CA4 613 214 7392 COMPL PWB,CA-4
NJ500 411 192 1308 S-TPG BIN 3X61
NJ600 411 192 0004 SCR S-TPG BIN 2X4
NJ621 411 031 8604 SCR BIN 3X6
NJ630 411 206 0303 SCR S-TPG BIN 4X6
NJ650 411 182 1905 SCR S-TPG BIN 3X4
NJ651 411 140 2500 SCR S-TPG BIN 3X12
NJ652 411 105 9704 WASHER Z 3X10X1

13
6420
NJ621
6470
6480
6490
NJ600
NJ651
NJ652
6003
CA4
6006
NJ650
NJ630
6040
5007
5006 5005
NJ500
L5CJ2-2
5019
6005
6050
5016
5018
#2

14
ELECTRICAL PARTS
Note:
1. Materials of Capacitors and Resistors are abbreviated as follows ;
Resistors Capacitors
MT-FILM Metallized Film Resistor MT-POLYEST Metallized Polyester Capacitor
MT-GLAZE Metallized Glaze Resistor MT-COMPO Metallized Composite Capacitor
OXIDE-MT Oxide Metallized Film Resistor TA-SOLID Tantalum Solid Capacitor
AL-SOLID Aluminum Solid Capacitor
NP-ELECT Non-Polarized Electrolytic Capacitor
OS-SOLID Aluminum Solid Capacitors with Organic
Semiconductive Electrolytic Capacitor
DL-ELECT Double Layered Electrolytic Capacitor
POS-SOLID Polymerized Organic Semiconductor Capacitor
2. Tolerance of Capacitor (10pF over) and Resistor are noted with follow symboles.
F ............1% G ............2% J ............5% K ............10%
M ..........20% N ..........30% Z ..........+80% ~ -20%
3. Capacitors
U : µF P : pF
4. Inductors
UH : µH MH : mH
5. N.S.P. : Not available as service parts.
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
COMPL PWB,CA-1
613 214 7309
(SEMICONDUCTORS)
Q1101 305 153 6702 TR 2SC3931-D
Q1201 305 168 4502 TR 2SA2029-R
OR 305 168 4601 TR 2SA2029-S
Q1202 305 172 8800 TR 2SC5658-R
OR 305 172 8909 TR 2SC5658-S
Q1203 305 172 8800 TR 2SC5658-R
OR 305 172 8909 TR 2SC5658-S
Q1204 305 014 4502 TR 2SC2412K-R
Q1205 305 168 4502 TR 2SA2029-R
OR 305 168 4601 TR 2SA2029-S
(INTEGRATED CIRCUIT)
IC102 409 678 8309 IC UPC358GR-9LG-A
(DIODES)
D1001 307 248 2408 ZENER DIODE EDZ7.5B
D1002 307 248 2408 ZENER DIODE EDZ7.5B
(VARIABLE RESISTORS)
VR101 945 005 5806 VR,SEMI,10K S
VR102 945 005 5806 VR,SEMI,10K S
VR103 945 061 9527 VR,SEMI,22K S
VR104 945 005 5806 VR,SEMI,10K S
(INDUCTORS)
L1201 645 018 3553 INDUCTOR,1000 OHM
L1202 645 018 3553 INDUCTOR,1000 OHM
L1203 645 018 3553 INDUCTOR,1000 OHM
L1204 645 018 3553 INDUCTOR,1000 OHM
(CAPACITORS)
C1002 303 338 0309 CERAMIC 0.1U K 10V
C1003 303 338 0309 CERAMIC 0.1U K 10V
C1004 303 338 0309 CERAMIC 0.1U K 10V
C1101 303 323 6309 CERAMIC 0.1U K 16V
C1102 303 420 7209 CERAMIC 10U K 10V
C1103 303 420 7209 CERAMIC 10U K 10V
C1104 403 455 1606 CERAMIC 10U K 16V
C1105 303 155 1800 CERAMIC 0.01U K 25V
C1106 403 455 1606 CERAMIC 10U K 16V
C1107 303 283 5701 CERAMIC 2200P K 50V
C1108 303 155 1800 CERAMIC 0.01U K 25V
C1109 303 323 6309 CERAMIC 0.1U K 16V
C1110 303 342 3303 CERAMIC 0.1U K 25V
C1111 303 338 0309 CERAMIC 0.1U K 10V
C1201 303 338 0309 CERAMIC 0.1U K 10V
C1202 303 338 0309 CERAMIC 0.1U K 10V
C1203 303 376 8404 CERAMIC 4.7U K 6.3V
C1204 303 387 3009 CERAMIC 4.7U K 10V
C1205 303 336 3500 CERAMIC 0.47U K 16V
C1206 303 342 3303 CERAMIC 0.1U K 25V
C1209 303 381 4705 ELECT 22U M 16V
C1210 303 336 3500 CERAMIC 0.47U K 16V
C1211 303 382 1901 ELECT 47U M 16V
C1212 303 323 6309 CERAMIC 0.1U K 16V
(RESISTOR PACKS)
RB101 645 063 0781 R-NETWORK 6.8KX4 1/32W
RB102 645 063 0781 R-NETWORK 6.8KX4 1/32W
RB103 645 063 0781 R-NETWORK 6.8KX4 1/32W
RB104 645 063 0781 R-NETWORK 6.8KX4 1/32W
(RESISTORS)
R1001 301 262 1904 MT-GLAZE 6.8K DC 1/16W
R1002 301 262 1904 MT-GLAZE 6.8K DC 1/16W
R1003 301 262 1904 MT-GLAZE 6.8K DC 1/16W
R1004 301 234 9907 MT-GLAZE 6.8K JA 1/16W
R1101 301 105 7902 MT-GLAZE 0.000 ZA 1/16W
R1102 301 038 2104 MT-GLAZE 2.7K JA 1/10W
R1103 301 224 9405 MT-GLAZE 1.0M JA 1/16W
R1104 301 225 0906 MT-GLAZE 82K JA 1/16W
R1201 301 226 1506 MT-GLAZE 0.000 ZA 1/16W
R1202 301 224 9207 MT-GLAZE 15K JA 1/16W
R1203 301 225 0203 MT-GLAZE 3.3K JA 1/16W
R1204 301 227 5602 MT-GLAZE 8.2K JA 1/16W
R1205 301 224 9306 MT-GLAZE 1K JA 1/16W
R1207 301 225 1200 MT-GLAZE 4.7K JA 1/16W
R1208 301 224 8903 MT-GLAZE 100K JA 1/16W
R1209 301 225 0708 MT-GLAZE 56K JA 1/16W
R1210 301 224 9306 MT-GLAZE 1K JA 1/16W
R1211 301 225 1200 MT-GLAZE 4.7K JA 1/16W
R1212 301 225 1200 MT-GLAZE 4.7K JA 1/16W
R1213 301 224 9306 MT-GLAZE 1K JA 1/16W
R1214 301 225 1200 MT-GLAZE 4.7K JA 1/16W
R1215 301 225 1200 MT-GLAZE 4.7K JA 1/16W
R1216 301 105 0507 MT-GLAZE 1K JA 1/16W
R1217 301 225 0609 MT-GLAZE 5.6K JA 1/16W
R1218 301 225 0104 MT-GLAZE 27K JA 1/16W
R1219 301 226 1506 MT-GLAZE 0.000 ZA 1/16W
R1220 301 226 1506 MT-GLAZE 0.000 ZA 1/16W
R1221 301 226 1506 MT-GLAZE 0.000 ZA 1/16W
R1222 301 224 9405 MT-GLAZE 1.0M JA 1/16W
R1223 301 037 5007 MT-GLAZE 0.000 ZA 1/10W
R1224 301 037 5007 MT-GLAZE 0.000 ZA 1/10W
R1226 301 224 9900 MT-GLAZE 22K JA 1/16W
(SWITCH)
S1001 645 067 6826 SWITCH,SLIDE 1P-1TX7
(MISCELLANEOUS)
W1001 613 201 2119 ASSY,WIRE (N.S.P)
(CONNECTORS)
CN101 945 074 0207 PLUG,2P (N.S.P)
CN102 645 051 0717 PLUG,PWB-PWB 30P (N.S.P)

15
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
COMPL PWB,CA-2 F/W
613 214 8146 VCC-9685VP ONLY
613 215 1368 VCC-9684VA ONLY
(SEMICONDUCTORS)
Q2001 305 168 4502 TR 2SA2029-R
OR 305 168 4601 TR 2SA2029-S
Q2002 305 168 4502 TR 2SA2029-R
OR 305 168 4601 TR 2SA2029-S
Q2003 305 172 8800 TR 2SC5658-R
OR 305 172 8909 TR 2SC5658-S
Q2004 305 172 8800 TR 2SC5658-R
OR 305 172 8909 TR 2SC5658-S
Q2301 305 115 5705 TR DTA144EE
Q2302 305 115 5705 TR DTA144EE
(INTEGRATED CIRCUITS)
IC201 309 478 2203 IC NJM2274R
IC211 310 550 1304 IC SCC0021A
IC221 309 320 9107 IC TC7SU04FU
IC222 309 323 9005 IC TC7S04FU
IC232 309 320 9107 IC TC7SU04FU
IC233 409 678 8309 IC UPC358GR-9LG-A
IC234 309 323 9005 IC TC7S04FU
IC235 309 320 9107 IC TC7SU04FU
IC236 309 323 9005 IC TC7S04FU
IC241 309 446 8701 IC CXD3400N
IC251 309 541 4806 IC BD4829G
IC252 410 649 3803 IC UPD70F3210HYGK-9EU-A (N.S.P)
IC253 409 682 0900 IC LE24C042M-TLM-E
IC261 309 534 2703 IC XC6201P332M
IC262 310 607 4302 IC AD9948AKCPZW
(DIODES)
D2301 307 151 0409 VARACTOR DI HVU200A
D2303 307 155 5509 VARACTOR DI HVU316
D2304 307 155 5509 VARACTOR DI HVU316
D2401 307 210 1903 DIODE 1SS400
OR 307 226 4806 DIODE BAS516
D2501 307 210 1903 DIODE 1SS400
OR 307 226 4806 DIODE BAS516
(OSCILLATORS)
X2201 645 049 0590 OSC,CRYSTAL 14.31818MHZ,
VCC-9684VA ONLY
X2201 645 055 5282 OSC,CRYSTAL 17.734475MHZ,
VCC-9685VP ONLY
X2301 645 057 4566 OSC,CRYSTAL 28.375MHZ,
VCC-9685VP ONLY
X2301 645 057 4573 OSC,CRYSTAL 28.63636MHZ,
VCC-9684VA ONLY
X2501 645 053 8483 OSC,CERAMIC 10.000MHZ
(TRIMMERS)
CT221 645 069 5131 TRIMMER,30PF
CT231 645 069 5131 TRIMMER,30PF
(INDUCTORS)
L2001 945 055 3135 INDUCTOR,68U J
L2002 945 043 7381 INDUCTOR,33U J
L2004 945 043 5882 INDUCTOR,10U J
L2301 945 004 2615 INDUCTOR,2.2U J
L2302 945 043 5882 INDUCTOR,10U J
L2303 945 043 5899 INDUCTOR,47U J
L2501 945 043 5882 INDUCTOR,10U J
L2601 945 066 4725 IMPEDANCE,600 OHM P
(CAPACITORS)
CB261 303 392 5500 CERAMIC 1U K 6.3V
C2002 303 276 2809 CERAMIC 18P J 50V,VCC-9685VP ONLY
C2002 303 309 2509 CERAMIC 27P J 50V,VCC-9684VA ONLY
C2003 303 305 8505 CERAMIC 15P J 50V
C2005 303 305 8505 CERAMIC 15P J 50V
C2006 303 276 1000 CERAMIC 0.01U K 16V
C2007 303 387 3009 CERAMIC 4.7U K 10V
C2008 303 338 0309 CERAMIC 0.1U K 10V
C2009 303 338 0309 CERAMIC 0.1U K 10V
C2010 303 378 3605 POS-SOLID 33U M 10V
C2011 303 338 0309 CERAMIC 0.1U K 10V
C2012 303 378 5302 CERAMIC 1U K 10V
C2013 303 393 2607 CERAMIC 22U M 6.3V
C2014 303 381 4804 ELECT 100U M 6.3V
C2015 303 381 4804 ELECT 100U M 6.3V
C2101 303 384 6508 CERAMIC 10U K 6.3V
C2102 303 384 6508 CERAMIC 10U K 6.3V
C2103 303 338 0309 CERAMIC 0.1U K 10V
C2104 303 338 0309 CERAMIC 0.1U K 10V
C2105 303 338 0309 CERAMIC 0.1U K 10V
C2106 303 338 0309 CERAMIC 0.1U K 10V
C2107 303 376 8404 CERAMIC 4.7U K 6.3V
C2108 303 338 0309 CERAMIC 0.1U K 10V
C2109 303 338 0309 CERAMIC 0.1U K 10V
C2110 303 338 0309 CERAMIC 0.1U K 10V
C2111 303 338 0309 CERAMIC 0.1U K 10V
C2112 303 376 8404 CERAMIC 4.7U K 6.3V
C2113 303 338 0309 CERAMIC 0.1U K 10V
C2114 303 338 0309 CERAMIC 0.1U K 10V
C2115 303 338 0309 CERAMIC 0.1U K 10V
C2116 303 376 8404 CERAMIC 4.7U K 6.3V
C2201 303 276 1901 CERAMIC 22P J 50V,VCC-9685VP ONLY
C2201 303 276 2809 CERAMIC 18P J 50V,VCC-9684VA ONLY
C2202 303 338 0309 CERAMIC 0.1U K 10V
C2301 303 276 1000 CERAMIC 0.01U K 16V
C2302 303 378 6002 CERAMIC 4.7U K 16V
C2304 303 378 6002 CERAMIC 4.7U K 16V
C2305 303 276 1307 CERAMIC 1000P K 50V
C2307 303 286 1403 CERAMIC 10P D 50V,VCC-9684VA ONLY
C2307 303 305 8505 CERAMIC 15P J 50V,VCC-9685VP ONLY
C2308 303 276 1000 CERAMIC 0.01U K 16V
C2309 303 305 8505 CERAMIC 15P J 50V
C2310 303 397 7608 CERAMIC 1U K 25V
C2311 303 338 0309 CERAMIC 0.1U K 10V
C2312 303 323 6309 CERAMIC 0.1U K 16V
C2314 303 207 0300 CERAMIC 1U Z 16V
C2316 303 276 1307 CERAMIC 1000P K 50V
C2317 303 276 1000 CERAMIC 0.01U K 16V
C2318 303 276 1000 CERAMIC 0.01U K 16V
C2321 303 276 1307 CERAMIC 1000P K 50V
C2322 303 376 8404 CERAMIC 4.7U K 6.3V
C2324 303 338 0309 CERAMIC 0.1U K 10V
C2325 303 338 0309 CERAMIC 0.1U K 10V
C2326 303 338 0309 CERAMIC 0.1U K 10V
C2327 303 276 1307 CERAMIC 1000P K 50V
C2328 303 376 8404 CERAMIC 4.7U K 6.3V
C2402 303 338 0309 CERAMIC 0.1U K 10V
C2405 403 455 1606 CERAMIC 10U K 16V
C2406 403 455 1606 CERAMIC 10U K 16V
C2408 303 397 7608 CERAMIC 1U K 25V
C2410 303 342 3303 CERAMIC 0.1U K 25V
C2411 303 420 7209 CERAMIC 10U K 10V
C2412 303 338 0309 CERAMIC 0.1U K 10V
C2501 303 338 0309 CERAMIC 0.1U K 10V
C2503 303 384 6508 CERAMIC 10U K 6.3V
C2504 303 338 0309 CERAMIC 0.1U K 10V
C2505 303 338 0309 CERAMIC 0.1U K 10V
C2506 303 338 0309 CERAMIC 0.1U K 10V
C2507 303 338 0309 CERAMIC 0.1U K 10V
C2509 303 384 6508 CERAMIC 10U K 6.3V
C2510 303 338 0309 CERAMIC 0.1U K 10V
C2511 303 393 2607 CERAMIC 22U M 6.3V
C2513 303 323 6309 CERAMIC 0.1U K 16V
C2514 303 323 6309 CERAMIC 0.1U K 16V
C2601 303 378 5302 CERAMIC 1U K 10V
C2603 303 378 5302 CERAMIC 1U K 10V
C2604 303 338 0309 CERAMIC 0.1U K 10V
C2606 303 322 1008 CERAMIC 0.1U Z 16V
C2607 303 338 0309 CERAMIC 0.1U K 10V
C2608 303 384 6508 CERAMIC 10U K 6.3V
C2609 303 338 0309 CERAMIC 0.1U K 10V
C2611 303 384 6508 CERAMIC 10U K 6.3V
C2613 303 338 0309 CERAMIC 0.1U K 10V
C2615 303 384 6508 CERAMIC 10U K 6.3V
C2618 303 338 0309 CERAMIC 0.1U K 10V
(RESISTOR PACKS)
RB251 945 028 0710 R-NETWORK 10KX4 1/16W
RB261 945 049 0690 R-NETWORK 33X4 1/16W
RB262 945 049 0690 R-NETWORK 33X4 1/16W
RB263 945 049 0690 R-NETWORK 33X4 1/16W
(RESISTORS)
R2001 301 224 9306 MT-GLAZE 1K JA 1/16W
R2002 301 224 9306 MT-GLAZE 1K JA 1/16W

16
R2003 301 224 9306 MT-GLAZE 1K JA 1/16W
R2004 301 224 9306 MT-GLAZE 1K JA 1/16W
R2005 301 224 9504 MT-GLAZE 2.2K JA 1/16W
R2006 301 224 9306 MT-GLAZE 1K JA 1/16W
R2007 301 224 9306 MT-GLAZE 1K JA 1/16W
R2008 301 225 1408 MT-GLAZE 47K JA 1/16W
R2009 301 225 1408 MT-GLAZE 47K JA 1/16W
R2010 301 224 9306 MT-GLAZE 1K JA 1/16W
R2011 301 166 5305 MT-FILM 68 DC 1/16W
R2014 301 166 5305 MT-FILM 68 DC 1/16W
R2101 301 237 2509 MT-GLAZE 4.7 JA 1/16W
R2102 301 225 8100 MT-GLAZE 10 JA 1/16W
R2103 301 225 8100 MT-GLAZE 10 JA 1/16W
R2104 301 237 2509 MT-GLAZE 4.7 JA 1/16W
R2201 301 224 9405 MT-GLAZE 1.0M JA 1/16W
R2301 301 225 0500 MT-GLAZE 33K JA 1/16W
R2302 301 225 1705 MT-GLAZE 39K JA 1/16W
R2303 301 224 9405 MT-GLAZE 1.0M JA 1/16W
R2304 301 225 1705 MT-GLAZE 39K JA 1/16W
R2305 301 224 8903 MT-GLAZE 100K JA 1/16W
R2307 301 224 9009 MT-GLAZE 10K JA 1/16W
R2308 301 225 8704 MT-GLAZE 120K JA 1/16W
R2309 301 224 8903 MT-GLAZE 100K JA 1/16W
R2310 301 226 1506 MT-GLAZE 0.000 ZA 1/16W
R2311 301 224 9405 MT-GLAZE 1.0M JA 1/16W
R2312 301 225 8704 MT-GLAZE 120K JA 1/16W
R2313 301 224 9801 MT-GLAZE 220K JA 1/16W
R2314 301 225 1200 MT-GLAZE 4.7K JA 1/16W
R2315 301 225 1200 MT-GLAZE 4.7K JA 1/16W
R2316 301 226 1506 MT-GLAZE 0.000 ZA 1/16W
R2317 301 225 1408 MT-GLAZE 47K JA 1/16W
R2318 301 225 1200 MT-GLAZE 4.7K JA 1/16W
R2319 301 224 9009 MT-GLAZE 10K JA 1/16W
R2320 301 224 9009 MT-GLAZE 10K JA 1/16W
R2322 301 224 9009 MT-GLAZE 10K JA 1/16W
R2323 301 224 8903 MT-GLAZE 100K JA 1/16W
R2324 301 224 8903 MT-GLAZE 100K JA 1/16W
R2325 301 234 4803 MT-GLAZE 3.3 JA 1/16W
R2326 301 224 9009 MT-GLAZE 10K JA 1/16W
R2327 301 224 9405 MT-GLAZE 1.0M JA 1/16W
R2401 301 105 7902 MT-GLAZE 0.000 ZA 1/16W
R2402 301 105 7902 MT-GLAZE 0.000 ZA 1/16W
R2403 301 105 7902 MT-GLAZE 0.000 ZA 1/16W
R2404 301 224 8903 MT-GLAZE 100K JA 1/16W
R2501 301 224 9009 MT-GLAZE 10K JA 1/16W
R2502 301 225 1200 MT-GLAZE 4.7K JA 1/16W
R2503 301 224 9009 MT-GLAZE 10K JA 1/16W,
VCC-9684VA ONLY
R2504 301 224 9009 MT-GLAZE 10K JA 1/16W,
VCC-9685VP ONLY
R2505 301 224 9306 MT-GLAZE 1K JA 1/16W
R2506 301 225 0500 MT-GLAZE 33K JA 1/16W
R2507 301 224 9900 MT-GLAZE 22K JA 1/16W
R2510 301 224 9009 MT-GLAZE 10K JA 1/16W
R2601 301 148 6009 MT-GLAZE 2.2 JA 1/16W
R2603 301 105 7902 MT-GLAZE 0.000 ZA 1/16W
R2604 301 225 8100 MT-GLAZE 10 JA 1/16W
R2605 301 225 8100 MT-GLAZE 10 JA 1/16W
R2606 301 225 8100 MT-GLAZE 10 JA 1/16W
R2702 301 226 1506 MT-GLAZE 0.000 ZA 1/16W
(CONNECTORS)
CN201 645 054 1339 SOCKET,PWB-PWB 30(N.S.P)
CN203 645 054 1315 SOCKET,PWB-PWB 20(N.S.P)
CN205 645 077 0319 PLUG,PWB 7P (N.S.P)
COMPL PWB,CA-3
613 214 7361
(SEMICONDUCTORS)
Q3001 305 137 2003 TR 2SA1576A-R
Q3002 305 092 4104 TR 2SC4081-R
Q3101 305 131 0203 TR DTC144EUA
Q3102 305 133 8900 TR DTC114EUA
Q3103 305 092 4104 TR 2SC4081-R
Q3104 305 188 0409 TR 2SK3617-TL-E
Q3201 305 115 5101 TR 2SA1774 R
Q3202 305 115 5200 TR 2SC4617 R
OR 305 158 2501 TR 2SC4617-S
(INTEGRATED CIRCUITS)
IC301 309 167 7205 IC NJM2406F
IC311 309 506 8900 IC FA7700V
IC321 309 673 2206 IC TLV431
IC322 309 531 0900 IC TA76432
IC323 309 544 6609 IC SI-3012KS-TL
(DIODES)
D3101 307 206 6301 ZENER DIODE UDZS5.1B-TE17
D3102 307 222 1007 ZENER DIODE UDZS4.3B
D3103 307 218 7402 ZENER DIODE UDZS15B
D3105 307 238 3705 PHOTO COUPLE PS2701-AL
D3106 307 239 5005 DIODE RF071M2S PMDU
OR 307 251 2204 DIODE RF001M2S
D3201 307 239 5005 DIODE RF071M2S PMDU
OR 307 251 2204 DIODE RF001M2S
D3202 307 229 6807 DIODE RSX101M-30
D3203 307 239 5005 DIODE RF071M2S PMDU
OR 307 251 2204 DIODE RF001M2S
D3204 307 239 5005 DIODE RF071M2S PMDU
OR 307 251 2204 DIODE RF001M2S
D3205 307 208 9706 ZENER DIODE UDZS5.6B
(INDUCTORS)
L3201 945 049 2779 INDUCTOR,0.47U M
L3202 945 020 1913 INDUCTOR,240 OHM
(TRANSFORMER)
T3101 645 068 3756 TRANS,POWER,PULSE
(CAPACITORS)
C3002 303 384 6300 CERAMIC 2.2U K 6.3V
C3003 303 325 6307 CERAMIC 0.22U K 10V
C3004 303 215 2204 CERAMIC 0.01U K 50V
C3005 303 325 6307 CERAMIC 0.22U K 10V
C3006 303 323 6309 CERAMIC 0.1U K 16V
C3007 303 376 8404 CERAMIC 4.7U K 6.3V
C3008 303 113 3808 CERAMIC 1000P K 50V
C3102 303 356 6208 CERAMIC 2.2U K 10V
C3103 303 357 3305 CERAMIC 0.01U K 630V
C3104 303 232 5400 CERAMIC 0.1U Z 50V
C3105 303 323 6309 CERAMIC 0.1U K 16V
C3106 303 387 3108 CERAMIC 2.2U K 16V
C3107 303 364 5309 CERAMIC 2.2U K 6.3V
C3110 303 336 8109 CERAMIC 1U K 50V
C3111 303 452 7901 CERAMIC 2.2U K 100V
C3112 303 378 6309 CERAMIC 470P J 100V
C3113 303 376 9302 CERAMIC 0.047U K 250V
C3114 303 452 7901 CERAMIC 2.2U K 100V
C3115 303 452 7901 CERAMIC 2.2U K 100V
C3117 303 304 9305 ELECT 47U M 50V
C3201 303 379 3000 CERAMIC 10U K 16V
C3202 303 379 0207 POS-SOLID 68U M 6.3V
C3203 303 378 3605 POS-SOLID 33U M 10V
C3204 303 420 0606 CERAMIC 10U K 25V
C3205 303 379 0207 POS-SOLID 68U M 6.3V
C3206 303 420 0606 CERAMIC 10U K 25V
C3208 303 420 0606 CERAMIC 10U K 25V
C3210 303 323 6309 CERAMIC 0.1U K 16V
C3211 303 323 6309 CERAMIC 0.1U K 16V
C3213 303 358 5506 CERAMIC 0.1U K 25V
C3217 303 323 6309 CERAMIC 0.1U K 16V
C3219 303 379 0207 POS-SOLID 68U M 6.3V
C3221 303 378 3605 POS-SOLID 33U M 10V
C3222 303 323 6309 CERAMIC 0.1U K 16V
C3225 303 397 7608 CERAMIC 1U K 25V
(RESISTORS)
R3004 301 105 0606 MT-GLAZE 10K JA 1/16W
R3005 301 105 1603 MT-GLAZE 15K JA 1/16W
R3006 301 105 4208 MT-GLAZE 33K JA 1/16W
R3007 301 105 6004 MT-GLAZE 5.6K JA 1/16W
R3008 301 105 0705 MT-GLAZE 100K JA 1/16W
R3009 301 105 0705 MT-GLAZE 100K JA 1/16W
R3010 301 105 7902 MT-GLAZE 0.000 ZA 1/16W
R3011 301 105 6004 MT-GLAZE 5.6K JA 1/16W
R3012 301 105 0507 MT-GLAZE 1K JA 1/16W
R3013 301 105 0309 MT-GLAZE 10 JA 1/16W
R3014 301 105 7902 MT-GLAZE 0.000 ZA 1/16W
R3101 301 105 3409 MT-GLAZE 27K JA 1/16W
R3102 301 105 7605 MT-GLAZE 820K JA 1/16W
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION

17
R3103 301 105 0606 MT-GLAZE 10K JA 1/16W
R3104 301 167 1405 MT-FILM 33K DU 1/16W
R3106 301 105 0309 MT-GLAZE 10 JA 1/16W
R3107 301 105 6400 MT-GLAZE 68 JA 1/16W
R3108 301 105 1405 MT-GLAZE 150 JA 1/16W
R3110 301 105 4109 MT-GLAZE 3.3K JA 1/16W
R3112 301 105 6400 MT-GLAZE 68 JA 1/16W
R3113 301 105 6400 MT-GLAZE 68 JA 1/16W
R3114 301 105 6400 MT-GLAZE 68 JA 1/16W
R3115 301 105 6400 MT-GLAZE 68 JA 1/16W
R3116 301 105 6400 MT-GLAZE 68 JA 1/16W
R3202 301 105 5908 MT-GLAZE 560 JA 1/16W
R3204 301 105 3201 MT-GLAZE 270 JA 1/16W
R3205 301 105 5908 MT-GLAZE 560 JA 1/16W
R3206 301 105 7902 MT-GLAZE 0.000 ZA 1/16W
R3208 301 105 4109 MT-GLAZE 3.3K JA 1/16W
R3209 301 105 6004 MT-GLAZE 5.6K JA 1/16W
R3210 301 167 0101 MT-FILM 8.2K DU 1/16W
R3211 301 166 8108 MT-FILM 1K DU 1/16W
R3212 301 166 7408 MT-FILM 510 DU 1/16W
R3213 301 166 8306 MT-FILM 1.2K DU 1/16W
R3214 301 166 8108 MT-FILM 1K DU 1/16W
R3215 301 166 7101 MT-FILM 390 DU 1/16W
R3220 301 166 8801 MT-FILM 2.2K DU 1/16W
R3221 301 105 8206 MT-GLAZE 68K JA 1/16W
R3222 301 167 1108 MT-FILM 24K DU 1/16W
R3223 301 105 7902 MT-GLAZE 0.000 ZA 1/16W
(CONNECTORS)
CN302 645 050 2446 PLUG,PWB-PWB 20P (N.S.P)
CN304 645 002 3033 PLUG,5P (N.S.P)
COMPL PWB,CA-4
613 214 7392
(VARISTOR)
VA401 308 050 2006 VARISTOR AVR-M1608C270MT
(DIODES)
D4001 307 100 1204 DIODE S1ZB20
D4002 307 199 4902 DIODE 1SS376
OR 307 226 3908 DIODE RSD376
D4003 307 238 3705 PHOTO COUPLE PS2701-AL
(CAPACITORS)
C4001 303 379 7107 CERAMIC 1000P K 630V
C4002 303 379 7107 CERAMIC 1000P K 630V
C4003 303 379 7107 CERAMIC 1000P K 630V
C4004 303 316 6903 ELECT 220U M 50V
C4005 303 316 6903 ELECT 220U M 50V
C4006 303 215 2204 CERAMIC 0.01U K 50V
(RESISTORS)
R4001 301 038 7703 MT-GLAZE 5.6K JA 1/10W
R4002 301 038 7703 MT-GLAZE 5.6K JA 1/10W
R4003 301 038 7703 MT-GLAZE 5.6K JA 1/10W
R4004 301 038 7703 MT-GLAZE 5.6K JA 1/10W
R4101 301 105 7902 MT-GLAZE 0.000 ZA 1/16W
(FUSE)
F4001 323 031 5203 FUSE 125V 2A
(CONNECTORS)
CN401 945 074 0207 PLUG,2P (N.S.P)
CN402 645 002 3019 PLUG,3P (N.S.P)
CN403 645 002 3033 PLUG,5P (N.S.P)
CABLE
W3004 613 215 1559 ASSY,WIRE ,CA3-CA4 (N.S.P)
W4001 613 209 0698 ASSY,WIRE ,CN401-CA4,VIDEO OUT (N.S.P)
W4002 613 206 5511 ASSY,WIRE ,CN402-CA4,POWER IN (N.S.P)
LOCATION PARTS NO. DESCRIPTION

C1
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS
TABLE OF CONTENTS
OVERALL WIRING, BLOCK DIAGRAMS & CIRCUIT DIAGRAMS Page
OVERALL WIRING C3
OVERALL CIRCUIT BLOCK DIAGRAM C4
IC101, IC241 & IC262 BLOCK DIAGRAMS
CA-1 CIRCUIT C5
IC201, IC262 CIRCUIT WAVEFORMS C6
IC211 BLOCK DIAGRAM
IC211 CIRCUIT WAVEFORMS
CA-2 CIRCUIT (VCC-9685VP) C7
CA-2 CIRCUIT (VCC-9684VA) C12
CA-3 CIRCUIT C17
CA-4 CIRCUIT C18
PRINTED WIRING BOARDS (P.W.B.)
CA-1 BOARD (SIDE A & B) C19
CA-2 BOARD (SIDE A & B) C20
CA-3 BOARD (SIDE A & B)
CA-4 BOARD (SIDE A & B) C21

C2
NOTES:
1. All resistance values in "OHMS" unless otherwise noted.
(K=1,000 ; M=1,000,000)
2. All capacitance values in "µF" unless otherwise noted.
p=pico farad ; µ,u or U=micro farad
3. All inductance values in "µH" unless otherwise noted.
µ,u or U=micro henry ; m=milli henry
PRODUCT SAFETY NOTICE
THE COMPONENTS DESIGNATED BY A SYMBOL ( ) IN THIS
SCHEMATIC DIAGRAM DESIGNATES COMPONENTS WHOSE
VALUE ARE OF SPECIAL SIGNIFICANCE TO PRODUCT SAFETY.
SHOULD ANY COMPONENT DESIGNATED BY A SYMBOL NEED TO
BE REPLACED, USE ONLY THE PART DESIGNATED IN THE PARTS
LIST.
DO NOT DEVIATE FROM THE RESISTANCE, WATTAGE AND VOLT-
AGE RATINGS SHOWN.
EXPLANATORY NOTES (EXAMPLES)
Resistor 10K:1/16J means 10kilo ohm ±5%, 1/16watt max.
1M:1/10K means 1mega ohm ±10%, 1/10watt max.
Capacitor 0.047:F means 0.047micro farad, Ftype.
Electrolytic capacitor
10:16 means 10micro farad, 16volt max.
Inductor 330:J means 330micro henry ±5%
470:K means 470micro henry ±10%
No description J or K means ±5%
Figure of printed wiring boards
Multilayer board:
"Side A" means the view from A side of the board.
"Side B" means the view from B side of the board.
Singlelayer board:
View from the copper-foil side of the board, otherwise noted.
PAL-F-EX
The number of "H=##" written in slant character, shows the voltage.
The number of "H=##" written in upright character, shows the height of the parts.

A
B
C
D
E
F
G
H
I
J
K
12345678910 11 12 13 14 15 16 17 18 19
A
B
C
D
E
F
G
H
I
J
K
C3
OVERALL WIRING, BLOCK DIAGRAMS & CIRCUIT DIAGRAMS
OVERALL WIRING
CN102
10
V1
4
H2
11
-5V(CCD)
5
GND
12
WB-B
6
RG
13
CCD_LEVEL
7
SW1
14
6V(LENS)
8
MONITOR
15
IRIS_REF_IN
9
V3
16
IRIS_REF_OUT
17
6V(LENS)
18
3.3V
19
WB-R
20
12V(CCD)
1
GND
2
GND
3
GND
21
V2
22
V4
23
SUB
24
LL-VR
25
SW2
26
SW3
27
H1
28
GND
29
CCDOUT
30
GND
CN201
10
V1
4
H2
11
-5V(CCD)
5
GND
12
WB-B
6
RG
13
CCD LEVEL
7
SW1
14
6V(LENS)
8
MONITOR
15
IRIS REF IN
9
V3
16
IRIS REF OUT
17
6V(LENS)
18
3.3V
19
WB-R
20
12V(CCD)
1
GND
2
GND
3
GND
21
V2
22
V4
23
SUB
24
LL-VR
25
SW2
26
SW3
27
H1
28
GND
29
CCDOUT
30
GND
CN203
10
GND
4
GND
11
GND
5
6V(LENS)
12
VIDEO OUT
6
5V
13
GND
7
LL-PULSE
14
LL-VR
8
GND
15
5V
9
GND
16
6V(LENS)
17
3.3V
18
3.3V
19
-5V(CCD)
20
12V(CCD)
1
12V(CCD)
2
-5V(CCD)
3
3.3V
CN101
1
MONITOROUT
2
GND
CN302
10
GND
4
GND
11
GND
5
6V(LENS)
12
VIDEO OUT
6
5V
13
GND
7
LL-PULSE
14
LL-VR
8
GND
15
5V
9
GND
16
6V(LENS)
17
3.3V
18
3.3V
19
-5V(CCD)
20
12V(CCD)
1
12V(CCD)
2
-5V(CCD)
3
3.3V
CN304
4
GND
5
VIDEO OUT
1
PHASE
2
DC36V
3
GND(DC36V)
CN403
W1-16800/L5CJ2-XE
4
GND
5
VIDEO OUT
1
PHASE
2
DC36V
3
GND(DC36V)
CN401
1
VIDEO OUT
VIDEO OUT
POWER IN
2
GND
CN402
1
AC24V/+
2
AC24V/-
3
F.GND
W1001
4
DRIVE-
1
BRAKE-
2
BRAKE+
3
DRIVE+
S1001
1 2 3 4 5 6 7 8
9
10 11 12 13 14
VR101 VR102
VR103 VR104
CN205
4
FLMD0
5
RS232OUT
6
RESET
1
+3.3V
TEST POINT
2
GND
3
RS232IN
7
FLMD1
ON
OFF
VARI
W3004
LL
WB-R
WB-BIRIS
_FOCAL
LENS
CA-1 CA-2 CA-3 CA-4
MONITOR OUT