Sanyo VDC-DP7585P User manual

INSTALLATION MANUAL
Color CCD Camera
THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED
SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL
CODES.
Please read this manual before installing and using this unit, and always follow the instructions
in it for proper use. Please also read the separate INSTRUCTION MANUAL before using the unit
for proper use.
This unit can be installed on the ceiling or wall.
When installing, first remove the built-in camera
from the unit.
bWhen routing the cables on ceiling or wall
surfaces:
Loosen the conduit hole cover fixing screw (A)
on the back of the camera unit base with the
hexagonal wrench (small), open the cover (B),
and pass the connection cables through the
conduit hole.
Since the conduit hole cover is not
waterproof-finished, always be sure to
seal the cover entirely by puttying, for
example, upon completion of installation.
Ceiling Installed (see page 1)
Wall Installed (see page 3)
(In-ceiling routing)
(Surface routing)
(In-wall routing) (Surface routing)
Important
• Be careful when opening holes for installing
the unit. Work with the power and video
cables pulled out for easy installation.
• Make sure to properly perform waterproofing
for the ceiling or wall where you are installing
the unit.
• Make sure that the surface in the installation
location has no unevenness and is strong
enough to bear the total weight of the unit.
• Install this unit in an environment where the
temperature range stays between -10°C
and +50°C (no condensation allowed).
• As a precaution against static electricity
damage, touch a nearby metal object (door
knob, etc.) to dissipate static electricity in
your body before touching this unit.
A
B
VDC-DP7585P
EnglishFrançaisDeutsch中文简体
L5BH2_XE(INSTALLATION).book 0 ページ ２００６年６月３０日 金曜日 午後６時３４分

1
Installing on the Ceiling
1Loosen the four screws (A) using the
hexagonal wrench (large) and open the
dome cover.
2Unplug all the pin connector cables from
the circuit board.
3Lift and turn the camera unit in the
arrowed directions so that the two
screws (B) become visible.
4Pull out the sliding plate (D) in the
arrowed direction while pushing the
spring (C) indicated with a blue sticker
in the arrowed direction.
The camera unit is released.
1Attach the cushioning sheet (E) to the
back of the camera unit base (F), open a
cable hole in the cushioning sheet, and
pass the cables through the cable hole.
2Position the arrow (2) on the inner side
of the camera unit base (F) in the
direction of the lens.
The arrow is located roughly in the center of
the panning range.
3Set the camera unit base (F) on the
ceiling and secure it by tightening
suitable screws and washers (G)
through the screw holes (4 places).
•Length: 35 mm or more
•Diameter: 3.5 to 5.0 mm
•Height of screw head: 5 mm or less
(washer included)
1. Remove the camera unit
1
2
3
4
C
D
A
A
B
A
A
2. Install the camera unit base
Make sure to tighten the screws properly.
Using screws of sizes other than
specified may cause the unit to fall.
E
F
GG
3
2
1
L5BH2_XE(INSTALLATION).book 1 ページ ２００６年６月３０日 金曜日 午後６時３４分

2
1Connect the cables from the ceiling.
Push the excess of connected cables into
the ceiling.
For details on the connections, see page 5.
2Check that the spring (H) on the base
chassis looks as shown in the figure
below.
3Mount the camera unit using the two
base screws (J).
4Push the sliding plate (K) in the arrowed
direction until it clicks, then connect the
pin connector cables from the camera
unit base to the circuit board.
bSet up the camera remotely (see page 7).
bCheck the settings screen or camera
angle on a portable monitor (see page 7).
1Adjust the angle of view by moving the
lens unit manually.
Make the arrow (AA) beside the lens point
upwards (the video image will be upside
down if pointing downwards).
2Shape the flat cable on the back of the
lens unit.
1Hook the cable on the back of the clamp
as shown in the figure.
2Pull the cable in the arrowed direction
until the sag is gone.
3 Fold over the excess cable until there is no
more sag and insert it into the holder slits.
3. Mount the camera unit
H
J
H
K
2
4
4. Adjust/Check the video image
from the camera
Adjusting the lens position
and shaping the flat cable
Vertical or horizontal smear (streak
noise) may appear if the camera faces
an extremely bright light source. If so,
change the lighting angle while checking
the quality of the image on the monitor.
180°
330°
90°
AA
2
1
3
L5BH2_XE(INSTALLATION).book 2 ページ ２００６年６月３０日 金曜日 午後６時３４分

3
Installing on the Ceiling
1Align the logo on the dome cover with
the mark (L) on either side of the camera
unit base so that the lens is close to the
camera window (M).
2Loosen the screws (N) in the inner side
of the dome cover and shift the dome
liner (P) until the lens is completely
visible from the camera window.
3Secure the dome cover by tightening the
screws (R) (4 places) firmly using the
hexagonal wrench (large).
5. Install the dome cover
N
P
L
RR
M
Installing on the Wall
See “Installing on the Ceiling” (see page 1).
1Attach the cushioning sheet (A) to the
back of the camera unit base (B), open a
cable hole in the cushioning sheet, and
pass the cables through the cable hole.
2Set the camera unit base (B) on the wall
so that its tightening screws (C) are
perfectly horizontal, then tighten them
securely with washers (4 places).
•Length: 35 mm or more
•Diameter: 3.5 to 5.0 mm
•Height of screw head: 5 mm or less
(washer included)
1. Remove the camera unit
2. Install the camera unit base
C
C
B
A
L5BH2_XE(INSTALLATION).book 3 ページ ２００６年６月３０日 金曜日 午後６時３４分

4
1Connect the cables from the wall.
Push the excess of connected cables into the wall.
For details on the connections, see page 5.
2Check that the spring (D) on the base
chassis looks as shown in the figure
below.
3Mount the camera unit using the two
base screws (E).
4Push the sliding plate (F) in the arrowed
direction until it clicks, then connect the
pin connector cables from the camera
unit base to the circuit board.
bSet up the camera remotely (see page 7).
bCheck the settings screen or camera
angle on a portable monitor (see page 7).
If the image is upside down, correct the
orientation by turning down the lens unit,
rotating it 180 degrees, and then turning it up
in the arrowed directions.
See “Adjusting the lens position and
shaping the flat cable” on page 2.
See “Installing on the Ceiling” (see page 3).
3. Mount the camera unit
D
E
E
F
4
4. Adjust/Check the video image
from the camera
• The video image will be upside down
if the arrow (AA) beside the lens
points downwards.
• Be careful not to damage the flat
cable when rotating the lens unit.
5. Install the dome cover
AA
L5BH2_XE(INSTALLATION).book 4 ページ ２００６年６月３０日 金曜日 午後６時３４分

5
~
~
GND
+
–
RED
BLACK
WHITE
YELLOW
PURPLE
ORANGE
BLUE
GRAY
GND
DAY/NIGHT
ALARM IN
TELE
WIDE
COMMON
DC12 AC24
+
–
~
~
Connections
BNC type
RG-6U, 300 m max.
For the connection, use a RG-6U coaxial
cable.
Monitor Connection
bWith AC 24 V
Power Supply Connection
• Using different cables from those
specified here may attenuate the
video and/or sync signals and
interfere with correct transmission.
• RG-59U coaxial cables can be
used when distance between
devices is short, but not in duct or
aerial routing.
Cable type Length
RG-59U (3C-2V) 150 m max.
RG-6U (5C-2V) 300 m max.
RG-11U (7C-2V) 350 m max.
bWith DC 12 V
Check that +/- polarity is correct.
(RED)
(BLACK)
(WHITE)
For the connections, use cables thicker than
18 AWG.
(RED)
(BLACK)
To prevent electromagnetic
interference
• On the cable for power supply
Be sure to attach the supplied clamping
core to the cables as illustrated.
For the connections, use cables thicker than
18 AWG.
Do not connect the power cord until all other connections have been completed.
L5BH2_XE(INSTALLATION).book 5 ページ ２００６年６月３０日 金曜日 午後６時３４分

6
SYNC
BLC
IRIS
WHITE BALANCE
AGC GAIN
GAMMA
SHUTTER
APERTURE
·DAY/NIGHT
OPTION
PRESET
MENU
INT
OFF
SET y
ATW
NORM
0.45
50
HIGH
COLORy
SET y
OFF
END
T
N
N
2
4
AB
OPTION
TITLE
PRIVACY MASK
PASSWORD
·ALARM
LANGUAGE
OFF
SET y
SET y
SET y
SET y
SYNC
BLC
IRIS
WHITE BALANCE
AGC GAIN
GAMMA
SHUTTER
APERTURE
DAY/NIGHT
·OPTION
PRESET
MENU
INT
OFF
SET y
ATW
NORM
0.45
50
HIGH
AUTO y
SET y
OFF
END
For details, see “Specifying Alarm Input” in
the INSTRUCTION MANUAL.
The video image can be fixed to be color or
black-and-white using an external switch.
For details, see “Adjusting DAY/NIGHT
Function” in the INSTRUCTION MANUAL.
Color or Black-and-White Setting
(GRAY)
(PURPLE) Alarm
input signal
Alarm Signal Input
(GRAY)
(BLUE)
Open: Color
Closed: Black-and-White
(GRAY)
(YELLOW)
• Make sure that COLOR is selected.
All connection cables should be 24 AWG or higher with a maximum length of no
more than 600 m.
(ORANGE)
For customers using the option board
(heater: VA-50H)
For this unit, the main board (A) is
sufficient to raise the temperature. Always
be sure to remove the sub board (B).
It is used to make wide angle/telescoping
adjustments.
Connection for Zoom Input
Zoom Input Signal
TELE WIDE
L5BH2_XE(INSTALLATION).book 6 ページ ２００６年６月３０日 金曜日 午後６時３４分

7
Adjusting the Camera
bSetting up the camera remotely
Use of the separately ordered Camera Control Unit (VAC-70) is recommended for setting and adjustment of
this camera. Advanced settings are possible from the main menu. For details, see the instruction manual for
the Camera Control Unit
.
bInstallation accessories
Do not forget to disconnect the Camera Control Unit once you have finished setting/adjustment.
Checking the settings screen or camera angle on a portable monitor
(These checks are unnecessary when using the separately
ordered Camera Control Unit (VAC-70).)
Connect the MONITOR OUT pin and the GND pin on the circuit
board to a monitor using an alligator clip cable. Do not forget to
remove the cable after you have finished checking.
A dedicated MONITOR OUT connector is provided for portable
monitors.
bTo check the settings screen and make changes
1) Hold down the SET button (1) for over a second.
The main menu appears.
2) Select a menu by pressing the Select button (2) up and
down.
3) Select the setting item and value by pressing the Select
button left and right.
bTo check the zoom position and make changes
Press the Select button left and right during live mode
(with no menu displayed).
You can set the zoom (wide: d, tele: c).
VIDEO OUT CAMERA DC IN 3V
Ð+
VAC-70
Video in
BNC type
RG-6U coaxial cable
300 m max.
UP
DOWN
LEFT
RIGHT
SET
GND
MONITOR
OUT
1
2
1Hexagonal wrench
(large, small)
2Cushioning sheet 3Clamping core
L5BH2_XE(INSTALLATION).book 7 ページ ２００６年６月３０日 金曜日 午後６時３４分