SARK 200 User manual

SARK 200 Mini PBX
Sangoma Vega Gateways
Quick start configuration guide for SARK and Sangoma Vega 0 FXO Gateway
Before You Begin:
•The SARK PBX and Vega 50 appliance is connected to the network and all IP
addresses are configured as needed If not then please consult links below for
SARK and Vega 50
SARK PBX Quick Start Guide
Vega 50 Quick Start Guide
•You are able to connect to the Web interface of both SARK PBX and Vega 50
SARK PBX Configuration
Open a browser and enter IP address of Sark PBX On prompt enter the following details
SARK 200 / SARK 00
User Name : admin (lower case)
Password : sarkadmin (lower case)
SARK 8 0/1000/1200
User Name : admin (lower case)
Password : Aster2sk!

Step 1 :
Create a sip trunk between Sark and Vega 50 box To do that go to :
End Points >> Trunks and click on New Object icon as shown below
Choose GeneralSIP from Trunk Type drop down menu Some extra fields will appear on
the screen
Set a name for the trunk (Without Space) and insert the IP address of the Vega gateway
Leave everything else as default and press save and then the commit button
Step 2 :
Next step is to create an inbound route for calls coming from Vega gateway to Sark This is
where you define the numbers assigned to you by Fixed line provider generally BT/Virgin
Media for UK
The default route in Sark (_XXXX ) match any DID number coming in to Sark and forward
it to the system operator It is good practice to specify the line number which gives more
control on inbound call routing

To add a DID click on new object icon and select DID from Carrier drop down menu Now
enter a name for the incoming line Enter the DID(geographic) number associated with
PSTN line and press save and then the commit button
Finally add any extra DID`s for additional lines and press commit button to save and apply
settings See example of DID`s below
Step 3:
The next step is to create outbound route, for this go to Routing >> Route(outbound) this
will take you to the following page
You can either change the default route below or create a new outbound route by clicking
New

You can change the route name to anything you like For Path1 you will need to select the
name of your Trunk discussed in step 1, in this case it is “Vega50”, then leave the rest of
the settings as default
Vega 0 4-8 Port FXO Configuration
Open a browser and enter IP address of Vega 50 On prompt enter the details as below to
log in
User Name : admin
Password : admin
Step 4:
On main login page click on Quick Config and press Continue on prompt
Step :
Basic config
Under General menu Select the country where Vega is to be commissioned Then select a
valid static IP address for the Vega box Also remember to change the login password

Step 6:
VoIP
Next go to VoIP section and enter the IP address of SARK as SIP domain and SIP server
IP/Name Make sure registration mode is turn off and change codec 1 priory to
G711Alaw64k or as shown below
Step 7:
FXO
Next go to FXO section Enable the check box for Tone Based Discount, Handle
Emergency calls and Call ID Detection.
Enabling emergency calls feature will automatically create a dial plan on Vega 50 to pass

all emergency calls over FXO line where as Call ID detection feature is only needed when
the service is activated from the service provider side
Next change Telephone numbers(s) to route field to ( *) for all FXO ports or as shown
below Add the DID numbers provided by fixed line provider under DID to Forward to SIP
and make sure the numbers under DID to Forward section matches the inbound numbers
created on Sark in step 2
Finally select the New Install ? Check box and press the Submit button Wait couple of
seconds and press the Reboot system button when it appears
Now you should be able to make/receive calls from and to Vega/SARK PBX