Sase Bull 240 User guide

SASE
BULL 240C
Dust Collection System
Manual
www.SASECompany.com 800.522.2606 [e-mail]

www.SASECompany.com
1
Contents
2|
Symbols
3|
Safety Instructions
3|
Intended Use
4|
Design of the Bull 240
5|
Product Description
6|
Technical Data
7|
Warnings
8|
Maintenance and Service
9|
Replacement of the Dust Bag
10|
Replacement of the Polyester Filter
11|
Replacement of the HEPA Filters
12|
Manual Cleaning of the Polyester Filter (Back flush)
13|
Trouble-Shooting
14|
EC Declaration of Conformity
15
Elongated Bag Holder

www.SASECompany.com
2
Symbols
Warning!
Be cautious when you see this sign and pay attention to the
warning relevant to the situation.
Safety precautions accompanied by this symbol indicate a
danger of injury.
Important!
When you see this symbol, pay attention as some important and
relevant information is mentioned.
Safety precautions accompanied by this symbol indicate a
danger of damage to the machine.
Read carefully
Take the time to read this manual before using the machine for
the first time. It contains useful information about its
installation, its functions and its maintenance.
Maintenance
When this symbol is displayed, instructions relevant to the
maintenance of the machine will be given.
Unplug the machine
When this symbol is displayed, the machine must be turned off
and its power supply removed from the electricity outlet.
Visual check
When this symbol appears, make sure to look attentively at the
part of the machine mentioned in the instructions.

www.SASECompany.com
3
Safety Instructions
The following documents should be read attentively and in their whole. They need to be understood by
all involved staff before proceeding with the installation and the start up as well as under use,
maintenance and service:
The user’s manual (this document)
Elongated bag manual (if applicable)
These instructions must be followed closely and kept where the machine is used.
Installation and use are to be performed only by trained and authorized staff.
All instructions in this manual are to be followed for the warranty to be valid. Performing an
action against recommended instructions will invalidate the warranty and can, in some case,
cause damage to the machine and/or injuries to the user.
Intended Use
The Bull 240 is intended for general cleaning in both commercial and industrial environments.
The Bull 240 in its standard version is NOT intended for the suction of
water or wet, explosive or inflammable material.

www.SASECompany.com
4
Design of the Bull 240C
Top of the cyclone
Cyclone (filter housing)
with polyester filter
Lever for manual filter cleaning
Strap to secure the dust bag
Dust bag
Top of the HEPA filter housing
(
Bull 240C
has two HEPA filters)

www.SASECompany.com
5
Product Description
Product designation Bull 240C
Description Bull 240Cconsisting of electrical motor, separator with one polyester filter
and two HEPA filters according to the model.
The Bull 240C
is principally made of iron and painted with powder coating.
Environment The choice of material and production method has been very important
during the design of the mobile vacuum cleaner. The Bull 240Cis recyclable
to 98 %. Exceptions are some electrical components. No solvents are used
during the coating, neither for cleaning nor coat mixing.
Material
Stand Iron, quality SIS 1312
Cyclone Iron, quality SIS 1312
Filter End plates of metal or plastic.
Filter material of cellulose or polyester.
Motor Aluminium, iron and copper.
Plastic details Polyethylene and Bakelite.
Paint Polyester powder, TGIC-free.
Sealing Natural rubber.
Manufacturer SASE Company
2475 Stock Creek Blvd.
Rockford, TN 37853
Tel: [phone]
Fax: [phone]
www.SASECompany.com

www.SASECompany.com
6
Technical Data
Size (LxWxH) [cm] 56x80x112
Weight (approx.) [kg] 42
Voltage [V] 230/120
Current [A] 16 / 17,7
Power consumption [kW] 2,8
Air volume [m3/h] 420
Vacuum [mbar] 265
Sound level [dB] 65
Polyester lter [m2] 3,0
Filtration [%DOP] 98,89
HEPA lter H13
[m2]
[%DOP]
2x0,5
99,95
Dust bag [l] 35
Hose Ø [mm] 50
Consumables
Dust bags (10 pcs) SAS.0009510
HEPA filter, 0,5 m2
SAS.90052
Front swivel wheel
SAS.90049
Rear solid wheel SAS.90050
Star lock for rear wheel SAS.90052
Hose connection inlet SAS.90053

www.SASECompany.com
7
Warnings
1. Before any kind of maintenance or service is carried out, turn off the
machine and remove the power supply from its socket.
This does not apply for the manual cleaning of the filter.
2. The vacuum cleaner is not to be used for vacuuming wet or damp
material/dust. If water or any wet/damp material enters the vacuum
cleaner, the machine must be stopped immediately, taken apart and
dried up before it can be used again.
3. The Bull 240 should, under no circumstances, be used for the suction
of burning, glowing, explosive or inflammable fluids or materials.
4. If the filter shows any sign of damage, it must be replaced before the
vacuum cleaner is used in order to avoid damages to the vacuum
pump/motor.
5. Always treat used filters and used dust bags with care since they might
contain hazardous dust. Put the used filter in a large plastic bag and
seal it tightly. You should always seal used dust bags too.
6. The Bull 240 must never be used without filter, dust bag or vacuum
filter.
7. All service, repair and trouble-shooting of the Bull 240 and the vacuum
pump are to only be performed by authorized staff.
8. Some dust may be harmful to the health and/or the environment.
Check with the regulation at your work place and in your country.
Disposal of used filters and dust bags must be made in accordance
with governmental regulations.

www.SASECompany.com
8
Maintenance and Service
1. Before any kind of maintenance or service is carried out, turn off the
machine and remove the power supply from its socket.
This does not apply for the manual cleaning of the filter.
2. Check the filter regularly, at least once a week or other suitable
interval depending on use. If necessary, clean the filter.
3. Change the filter at least once a year or more frequently depending
on use.
4. Change the filter if it shows any sign of damage or has a hole.
5. Change the dust bag before it becomes too full.
6. Please note that service and repair of the electrical system and the
vacuum pump are only to be performed by authorized staff.

www.SASECompany.com
9
Replacement of the Dust Bag
1. Turn the central vacuum off and unplug the
power supply.
2. Loosen the strap securing the bag holder in
place.
3. Close the dust bag with the sealing strip,
which is found at the upper edge of the
plastic bag.
4. Remove the dust bag carefully to keep it
from being damaged.
5. Fit a new dust bag in the dust container and
place its upper edge under the strap.
6. Tighten the strap to secure the bag in place.
The dust bag might contain hazardous and poisonous dust and should therefore be disposed of
according to governmental regulations. Used dust bags should always be closed completely and be
treated carefully. Use only original dust bags.
Dust
bag
Strap
Sealing
strip
Strap
Dust
bag